Advertisement
Quick Links
Wilson Ottoman Bed
Double Size
IMPORTANT OTTOMAN SAFETY WARNINGS
IMPORTANT – READ CAREFULLY – RETAIN FOR FUTURE REFERENCE
You must ensure that the mattress is on the bed frame before operating the
lift mechanism – Failure to do so could result in injury.
Keep hands clear of the mechanism when opening or closing the ottoman.
Beware of entrapment – Never reach in through the mechanism to access
the storage area.
Always ensure that the ottoman is FULLY opened before accessing the
storage area.
Do not exceed the maximum weight as specified in the table below:
Bed
Wilson
1.5 hour approx
Two person
assembly time
assembly
MK3 230413
with
Bed Size
Min Weight (kg) Max Weight (kg)
Single
Small Double
Double
King
O.S.B.
20
45
30
50
30
60
30
60
Advertisement
Related Manuals for DREAMS Wilson
Summary of Contents for DREAMS Wilson
- Page 1 O.S.B. Wilson Ottoman Bed with Double Size IMPORTANT OTTOMAN SAFETY WARNINGS IMPORTANT – READ CAREFULLY – RETAIN FOR FUTURE REFERENCE You must ensure that the mattress is on the bed frame before operating the lift mechanism – Failure to do so could result in injury.
- Page 2 LOWER THE BED FRAME TO TO ACCESS THE STORAGE AREA THE OTTOMAN FRAME MUST BE FULLY OPENED AND THEN FULLY CLOSED AFTERWARDS AVOID TRAPPING FINGERS! WARNING! HAZARD - DO NOT REACH INTO THE SPACE BELOW! Wilson Ottoman Bed - Assembly guide - Page 2...
- Page 3 Do not sit on the mattress whilst the platform is in motion or is in the raised position. o Users should only get in and out of bed when platform is in the flat (horizontal) position. Wilson Ottoman Bed - Assembly guide - Page 3...
- Page 4 Thank you Hello, thanks for choosing to purchase your bed from Dreams - you're now on your way to your best ever night's sleep. Before you begin building your bed, please take a moment to read through the instructions and make sure that you've got all the relevant parts listed on the following pages.
- Page 5 Ottoman support bar Metal lift up slat frame Fixed retaining bracket - footboard Angle Brackets Mattress Stoppers Parking bracket - slat-frame Tools required Tape measure Cross head screwdriver 0 10 1 Wilson Ottoman Bed - Assembly guide - Page 5...
- Page 6 Bolts (M8x25mm) for fitting ottoman support bar Ottoman support bar Flat washer for M8 bolts Spring washers for M8 bolts Q x1 P x1 Fixed retaining bracket Parking bracket - slat frame - footboard Wilson Ottoman Bed - Assembly guide - Page 6...
- Page 7 The mechanisms are labeled m(a) & m(b) please carefully follow the diagram below. Bolts should be in the centre of the long holes. m (b) m (a) blue blue Align with blue labels Wilson Ottoman Bed - Assembly guide - Page 7...
- Page 8 Bolt into the holes marked (L) with red labels. The mechanisms are labeled m(a) & m(b) please carefully follow the diagram below. Bolts should be in the centre of the long holes m(a) m(b) Align with red labels Wilson Ottoman Bed - Assembly guide - Page 8...
- Page 9 (k). Once all four corners are located tighten Note the screws drive straight into the side rail all the bolts using the Allen key (d). itself, there are no pilot holes. Wilson Ottoman Bed - Assembly guide - Page 9...
- Page 10 Turn the bed on its side and attach the fabric base cover (G) to bottom of the headboard, footboard & side rails using the velcro tape. Make sure the fabric is fixed evenly all round. Wilson Ottoman Bed - Assembly guide - Page 10...
- Page 11 Carefully lay frame down. Make sure there is an even gap on each side of about 8mm, as in the sketch. Holding the frame, tighten all six bolt sets 100% using spanner (h) & Allen key (d). Wilson Ottoman Bed - Assembly guide - Page 11...
- Page 12 Push x2 mattress stoppers (F) into metal frame, they should go all the way through the upper & lower metal sections. Wilson Ottoman Bed - Assembly guide - Page 12...
- Page 13 O.S.B. stem just touches the surface - better to do this AFTER the mattress is fitted. Wilson Ottoman Bed - Assembly guide - Page 13...
- Page 14 Set the inner stem to the correct length so the end just touches the retaining bracket - it needs to touch to hold it in position. 100% Adjust the retaining bracket (P) so the stem end scrapes the surface. Wilson Ottoman Bed - Assembly guide - Page 14...
- Page 15 Double: 750n Slat Dimensions (LWH cm) Double: 67 x 5.3 x 0.9 Distance between slats (cm) Double: 27.5 Floor to top of slat Top of side rail to top of slat Wilson Ottoman Bed - Assembly guide - Page 15...
- Page 16 Metal tends to be more resilient to everyday wear and tear. We recommend to gently dust your metal furniture and keep it dry to maintain its look. Thank you for shopping with us - we hope you have a great night's sleep Care and maintenance guide Wilson Ottoman Bed - - Page 16...
- Page 17 Little dreamers Keep the little ones entertained while you assemble your new purchase.
Need help?
Do you have a question about the Wilson and is the answer not in the manual?
Questions and answers