Advertisement
Quick Links
IMPORTANT: BEFORE STARTING TO ASSEMBLE THE BED - PLEASE READ THESE INSTRUCTIONS CAREFULLY.
Parts Identification
1
HEADBOARD END
4
Parts Checklist
Ref.
Description
1
Headboard
2
Footboard
3
Side Panel - Left
4
Side Panel - Right
5
Metal Slat Frame
6
Angle Brackets
160510
10
3
11
Qty
1
1
1
1
1
2
Page 1 of 8
SANA STORAGE BED
PLEASE READ this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the pack supplied and check the contents against the
parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in
a safe environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be
e k
t p
a
w
a
f y
o r
m
o y
u
n
g
h c
the danger of choking.
FOOTBOARD END
2
7
Ref.
Description
7
Cross Bar
8
Mattress Stoppers
9
Slat Frame Support Rail (wood)
10
Base Boards
11
Base Board Support Rails (wood)
d l i
e r
n
d
r u
n i
g
s a
e s
m
b
, y l
o t
5
FABRIC
HANDLE
8
9
6
Qty
1
2
1
2
4
a
o v
d i
Advertisement
Related Manuals for DREAMS SANA
Summary of Contents for DREAMS SANA
- Page 1 SANA STORAGE BED PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction. Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
-
Page 2: Additional Tools Required
Fittings Checklist HARDWARE NEEDED FOR BED ASSEMBLY (PACK A) Code Description Code Description Bolts (M8x30mm) for Allen Key (for M8 bolt) fitting side panels (3&4) and to headboard & footboard (1&2) Screws (5x50mm) for Spring Washers (for M8 bolts) fitting wooden support rail (9) to footboard (2) Flat Washers (for M8 bolts) HARDWARE FOR FITTING METAL SLAT FRA ME (PACK B) - Page 3 Bed Assembly - Use Pack 'A' Stage Fit two sets of bolts (A), spring washers (B) , and flat washers (C) to the holes in the headboard (1) as shown. Note: Do not tighten fully but leave 10mm protruding as in the diagram. Fit the side panels (3 &...
- Page 4 Bed Assembly - Use Pack 'A' Stage Square up the bed to 90 degrees - then using sets of bolts (A), spring washers (B) & flat washers (C) fit angle brackets (6) into threaded inserts in the corners of footboard (2) & the side panels (3&4). &...
- Page 5 Fit base boards - Use Pack 'A' Stage On the marked line in the centre of the Carefully fit Base Boards (10). footboard (2), fix slat frame support rail (9) using screws (E). Note that the screws drive straight into the footboard, there are no pilot holes.
- Page 6 Fitting Slat Frame - Use Pack ‘B’ Stage UN-TIE THE TWO MECHANISMS HOLD THEM FORWARD Slat Frame Support Bar iii) With help from your assistant, lift slat frame (5) onto slat frame support bars aligning labeled holes on slat frame with first set of holes in support bars (nearest to headboard).
- Page 7 Fitting Cross Bar - Use Pack 'B' Stage HEADBOARD END LABEL CROSS BAR FITS HERE Carefully hold cross bar (7) in position under the first set of holes in the support bars. The holes to use for cross bar are clearly labeled - look carefully at the drawing.
- Page 8 Fitting Slat Frame - Use Pack 'B' Stage Note: Be very careful what you store under the bed - the top of an item, like a suitcase or a box, must not touch the slats or they shall be damaged. Maximum storage height is 185 mm.
Need help?
Do you have a question about the SANA and is the answer not in the manual?
Questions and answers