Operation - DeWalt DCT410 Instruction Manual

T h e screen c a n be t u r n e d o n a n d v i e w e d w h e n it is not a t t a c h e d t o t h e
handle set, allowing easier maneuverability of t h e c a m e r a .
Camera Cable (Fig. 5)
Align t h e c a m e r a cable w i t h t h e c a m e r a c o n n e c t o r (D). P u s h in a n d
t u r n t h e c o n n e c t o r c o u n t e r c l o c k w i s e (camera screen facing you) t o
firmly a t t a c h .
To r e m o v e t h e c a m e r a cable, t u r n t h e c o n n e c t o r c l o c k w i s e (direction
of arrow).
Additional c a m e r a c a b l e a n d extensions are available at additional
c o s t . Please c o n t a c t D E W A L T Industrial Tool C o . , 7 0 1 East J o p p a
R o a d , Baltimore, M D 2 1 2 8 6 , call 1 - 8 0 0 - 4 - D E W A L T ( 1 - 8 0 0 - 4 3 3 - 9 2 5 8 )
or visit our w e b s i t e w w w . d e w a l t . c o m .
Hook and Magnet DCT410 (Fig. 6)
T h e h o o k is beneficial for retrieving c a b l e or wire located in tight
s p a c e s . T h e m a g n e t is beneficial for retrieving metal objects in tight
s p a c e s .
To a t t a c h t h e h o o k or m a g n e t , t u r n t h e knurled part of t h e c a m e r a
c o u n t e r c l o c k w i s e until it s t o p s . .
Align t h e h o o k or m a g n e t w i t h t h e gray groove (T) t h e n slide it d o w n
until t h e t a b s (U) at t h e t o p of t h e h o o k / m a g n e t are securely In t h e
n o t c h e s (V) located in t h e c a m e r a lens.
Turn t h e knurled part c l o c k w i s e t o lock t h e b a s e of t h e h o o k a n d
m a g n e t .
Hook, Magnet and Mirror DCT411
(Fig. 7, 8)
Follow t h e p r o c e s s b e l o w t o a s s e m b l e t h e h o o k , m a g n e t or mirror
o n t o t h e DGT411 9 m m c a m e r a .
I . W i t h t h e sleeve (W) o n t h e accessory, insert t h e b o t t o m of
a c c e s s o r y (bent wire) into t h e hole (X) in t h e 9 m m c a m e r a cable.
2. M a k e sure t h e a c c e s s o r y Is in t h e groove (Y) o n t h e sleeve
a n d slide t h e sleeve o n t o t h e c a m e r a until t h e sleeve covers
t h e hole (X).
10
FIG. 8
ACAUTION: Cut Hazard. Use care when handling hook.
Belt Hook (Fig. 9)
(Optional Accessory)
AWARNING: To reduce the risk of serious personal Injury, DO
NOT suspend tool overhead or suspend objects from the belt hook.
ONLY hang tool's belt hook from a work belt.
AWARNING: To reduce the risk of serious personal injury,
ensure the screw (Z) holding the belt hook is secure.
I M P O R T A N T : W h e n attaching or FIG. 9
removing t h e belt h o o k , use only
t h e s c r e w (Z) that is p r o v i d e d .
T h e belt h o o k (AA) c a n b e b e
a t t a c h e d t o either side of t h e tool
using only t h e s c r e w (Z) provided,
t o a c c o m m o d a t e left- or right-
h a n d e d users. If t h e h o o k is not
desired at all, it c a n b e r e m o v e d f r o m t h e tool.
To m o v e belt h o o k , remove t h e s c r e w (Z) that holds t h e belt h o o k In
place then reassemble o n t h e o p p o s i t e side.
OPERATION
Installing and Removing the Battery Pack
(Fig. 10)
N O T E : M a k e sure your battery p a c k is fully c h a r g e d .
To install t h e battery p a c k (A) into t h e tool handle, align t h e battery w i t h
t h e rails Inside t h e tool's handle a n d slide it firmly Into t h e handle until
y o u hear t h e lock s n a p into place.
FIG. 10
A
To remove t h e battery p a c k f r o m t h e tool, press t h e release b u t t o n (BB)
a n d firmly pull t h e battery p a c k o u t of t h e tool handle. Insert it into t h e
charger as d e s c r i b e d in t h e charger section of this manual.
Getting Started
I N I T I A L S E T U P
Language Setup
1 . Press t h e f o r w a r d or b a c k arrow t o select English, French or
Spanish.
E n g i l s h I
F r e n c h
S p a n i s h
11