Hide thumbs Also See for DW0165S:

Advertisement

DW0165S
User Manual
www.D
WALT.com
E
Please read these instructions before operating the product.
E
ES
F
PT
E
PT
NL
DK
SE
FIN
NO
PL
GR
CZ
RU
HU
SK
SI
BG
RO
EE
LV
LT
TR
HR

Advertisement

Table of Contents
loading

Summary of Contents for DeWalt DW0165S

  • Page 1 DW0165S User Manual www.D WALT.com Please read these instructions before operating the product.
  • Page 2 Figures DW0165S DW0165 4.5V DC FCC ID: 2ANWF-DW0165 IC: 23237-DW0165 4.5V DC...
  • Page 3 ≤ 45° ≤ 45°...
  • Page 4: User Safety

    IC: 23237-DW0165 4.5V DC 4.5V DC 4.5V DC The DW0165S tools emit a visible laser beam, as shown in Figure . The laser beam emitted is Laser Class 2 per IEC 60825-1 and complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.
  • Page 5: Battery Safety

    Battery Safety By default, distances are measured from the bottom of the tool to a wall or object (Figure WARNING: Batteries can explode or leak and To measure distances from the top or middle of the cause serious injury or fire. To reduce the risk: tool, or from the tool's endpiece (when it is flipped ALWAYS follow all instructions and warnings on open to measure from a corner), click...
  • Page 6: Measuring Area

    Measuring Area By default, distances are measured from the bottom of the tool to a wall or object (Figure You can measure the area of a wall, floor, or object. To measure distances from the top or middle of the Point the tool's laser (Figure ) toward a wall or tool, or from the tool's endpiece (when it is flipped...
  • Page 7 • If the tool can be positioned opposite the bottom On the bottom line of the display window, view the of the tall object (to create an angle ≤ 45°), use height of the building or object. the distances to 2 points to calculate the height (Figure Adding Measurements •...
  • Page 8: Changing The Unit Of Measure

    DW0165S. View the difference between the two measurements Use the DW0165S to measure each wall in the room at the bottom of the display window (Figure or space captured in the floor plan, and sync the measurements to the floor plan.
  • Page 9: Three Year Limited Warranty

    Three Year Limited Warranty WALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www.D WALT.com or call 1–800–4-D WALT (1–800–433–9258).
  • Page 10: Specifications

    Specifications Range 6in to 165ft (.15m to 50m) Measuring Accuracy* ± 1/16in (± 1.5mm)* Resolution** 1/16in (1mm)** Laser Class Class 2 (IEC/EN60825-1: 2007/2014) Laser Type ≤ 1.0mW @ 620-690nm Laser/Backlight Automatic Switch-off After 30s Unit Automatic Switch-off After 90s Continuous Measuring Area Volume Pythagoras 2-Point...
  • Page 11 Caution—use of controls or adjustments or performance —Reorient or relocate the receiving antenna. of procedures other than those specified herein may —Increase the separation between the equipment and result in hazardous radiation exposure. receiver. —Connect the equipment into an outlet on a circuit Caution: different from that to which the receiver is connected.
  • Page 12 Notes:...
  • Page 13 © 2017 D WALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286 Made in China 021474 December 2017...

Table of Contents