Vermeer SC30TX Operator's Manual
  1. Manuals
  2. Brands
  3. Vermeer Manuals
  4. Cutter
  5. SC30TX
  6. Operator's manual

Vermeer SC30TX Operator's Manual

Stump cutter
Hide thumbs
Table of Contents

Advertisement

Quick Links

SC30
TX
Operator's
Manual
SC30TX_o1_04
Serial No. 101 -
Order No. 105400CG4
Cabled Assembly No.163710180
Stump Cutter

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SC30TX and is the answer not in the manual?

Questions and answers

Related Manuals for Vermeer SC30TX

Summary of Contents for Vermeer SC30TX

  • Page 1 SC30 Stump Cutter Operator’s Manual SC30TX_o1_04 Serial No. 101 - Order No. 105400CG4 Cabled Assembly No.163710180...
  • Page 2 This manual explains the proper operation of your machine. Study and understand these instructions thoroughly before operating or maintaining the machine. Failure to do so could result in personal injury or equipment damage. Consult your Vermeer dealer if you do not understand the instructions in this manual, or need additional information.
  • Page 3 Orientation. Forward travel of this machine is toward the cutter wheel. Right and left sides are determined when facing in  the direction of forward travel. RADEMARKS VERMEER, VERMEER Logo, and SMARTSWEEP are trademarks of Vermeer Manufacturing Company. KOHLER and COMMAND PRO are trademarks of Kohler Co. SC30TX Stump Cutter...
  • Page 4 Vermeer’s option without charge by any authorized independent Vermeer dealer. The warranty repair or replacement must be made by a Vermeer independent authorized dealer at the dealer’s location. Vermeer will pay for replacement parts and such authorized dealer’s labor in accordance with Vermeer’s labor reimbursement policy. Vermeer reserves the right to supply remanufactured replacement parts as it deems appropriate.
  • Page 5 (7) Transportation costs, if any, of transporting to the Vermeer dealer. Freight costs, if any, of transporting replacement parts to the Vermeer dealer. (8) The travel time of the Vermeer dealer’s service personnel to make a repair on the retail purchaser’s site or other location (9) In no event shall Vermeer’s liability exceed the purchase price of the product, (10) Vermeer shall not be liable to any person under any circumstances for any incidental or consequential damages (including but not limited to, loss of profits, out of service time) occurring for any reason at any time.
  • Page 6 (12) Depreciation damage caused by normal wear, lack of reasonable and proper maintenance, failure to follow operating instructions, misuse, lack of proper protection during storage. (13) Accessory systems and electronics not of Vermeer’s manufacture are warranted only to the extent of such manufacturer’s respective Limited Warranty if any.
  • Page 7 NO DEALER WARRANTY. The selling dealer makes no warranty of its own and the dealer has no authority to make any representation or promise on behalf of Vermeer or to modify the terms or limitations of this warranty in any way.
  • Page 8 This page intentionally left blank.

  • Page 9: Engine

    General ___ Check all shields for installation and condition. ___ Check condition of cutter wheel guard. ___ Check machine for proper lubrication. ___ Check condition of all safety signs and decals. SC30TX Stump Cutter Receiving and Delivery Report i...

  • Page 10: Review Of Operation

    Review and demonstrate with the owner the various aspects of stump cutter operation: ___ overall explanation of how the machine works ___ machine safety ___ preparing the machine for operation ___ operating the machine ___ removing chips ii Receiving and Delivery Report SC30TX Stump Cutter...

  • Page 11: Dealer/Owner Information

    WNER NFORMATION dealer owner address address city city state / province state / province zip / postal code zip / postal code country country phone number phone number email address email address SC30TX Stump Cutter Receiving and Delivery Report iii...
  • Page 12 ACHINE DENTIFICATION UMBERS ECORD Machine Model Number ________________ Machine Serial Number ________________ NGINE DENTIFICATION UMBER ECORD Engine Model Number _________________ Engine Serial Number _________________ iv Receiving and Delivery Report SC30TX Stump Cutter...

  • Page 13: Machine Identification Decal

    ACHINE DENTIFICATION ECAL This decal provides easy identification of the model and 17-digit identification number. The barcode contains the machine’s VIN number and can be scanned with any barcode reading device.  SC30TX Stump Cutter Receiving and Delivery Report v...
  • Page 14 This page intentionally left blank.

  • Page 15: Table Of Contents

    After Engine Starts....... . . 22-2 SC30TX Stump Cutter Table of Contents vii...
  • Page 16 Index ..........viii Table of Contents SC30TX Stump Cutter...

  • Page 17: Safety Messages

    This symbol indicates that at least one part of the machine is not operating correctly. Shutting down the machine may not be necessary, but some maintenance may be required. SC30TX Stump Cutter Safety Messages 10-1...
  • Page 18  WARNING: Check machine before operating. Machine must be in good operating condition and all safety equipment installed and functioning properly. WARNING: Wear personal protective equipment. Dress properly. Refer to “Personal Protection,” page 40-2. 10-2 Safety Messages SC30TX Stump Cutter...
  • Page 19 Wait for leaking to stop before disconnecting the fitting. Fluid injected under the skin must be removed immediately by a surgeon familiar with this type of injury. SC30TX Stump Cutter Safety Messages 10-3...
  • Page 20 5 minutes. Turn fuel cap 1/4 turn, wait 10 seconds. Touch spout to tank to discharge static, then remove cap. Keep spout in contact with tank while filling. CAUTION: Hot muffler can burn. Stay away. 10-4 Safety Messages SC30TX Stump Cutter...
  • Page 21 WARNING: Failure to follow any of the preceding safety instructions or those that follow within this manual, could result in serious injury or death. This machine is to be used only for those purposes for which it was intended as explained in this Operator’s Manual. SC30TX Stump Cutter Safety Messages 10-5...
  • Page 22 This page intentionally left blank.

  • Page 23: Intended Use

    Always use the machine in accordance with the instructions contained in this Operator’s Manual, safety signs on the machine, and other material provided by Vermeer Corporation. Proper maintenance and repair is essential for safety, and for efficient operation of the machine. Do not use the machine if it is not in suitable operating condition.
  • Page 24 This page intentionally left blank.

  • Page 25: Controls

    Pull back ......decrease engine speed NOTICE: This Kohler EFI engine requires NO choke. Refer to Engine Operator’s Manual for more details. NOTICE: Do not touch the boom control lever while Ignition  system is powering up. SC30TX Stump Cutter Controls 20-1...
  • Page 26 (3) Hourmeter/Tachometer • Displays total machine hours when machine is off. • Display will flash for preset service reminders. Refer to “Maintenance Intervals,” page 60-3. Displays RPM when engine is running. 20-2 Controls SC30TX Stump Cutter...

  • Page 27: Machine Controls

    Push left lever forward and right lever back ..turn right Push right lever forward and left lever back ... turn left SC30TX Stump Cutter Controls 20-3...
  • Page 28 Push boom lever right ..... boom swing right Push boom lever left ..... . . boom swing left 20-4 Controls SC30TX Stump Cutter...

  • Page 29: Operator Presence Lights

    Before moving near cutter wheel, look to ensure rotation has stopped. • Cutter wheel drive will not remain engaged if this light is disconnected or shorted to ground. Maintain light in good working condition. (Ignition switch must be in RUN position.) SC30TX Stump Cutter Controls 20-5...
  • Page 30 This page intentionally left blank.

  • Page 31: Starting Procedure

    Refer to the Engine Operation Manual for more information. Step 4: Reduce Throttle to idle. • Do not operate engine under load until engine has warmed up. • For cold weather starting, refer to Engine Cold Weather Starting in this section. SC30TX Stump Cutter Starting Procedure 22-1...

  • Page 32: After Engine Starts

    • Check that machine does not move with Propel Lever in NEUTRAL. • Check that cutter wheel does not turn without Operator Presence system active. Hand must be on Boom Control Lever. 22-2 Starting Procedure SC30TX Stump Cutter...

  • Page 33: Cold Weather Starting

    NOTICE: Reduce engine speed if hydraulic pump whines. Pump noise may indicate lack of oil which can damage the pump. • Do not spray starting fluid into the air cleaner. Engine damage can result. SC30TX Stump Cutter Starting Procedure 22-3...

  • Page 34: Jump-Starting

    Vehicles in contact have a ground connection which allows a spark to occur at the battery when the positive jumper cable is connected or removed. If equipped with battery caps, they must be in place and tight to reduce risk of battery explosion. 22-4 Starting Procedure SC30TX Stump Cutter...

  • Page 35: Avoid Battery Burns

    Jump-Starting Procedure WARNING: Battery post, terminals, and related accessories contain lead and lead compounds, chemicals known to the state of California to cause cancer and reproductive harm.   Wash hands after handling.  SC30TX Stump Cutter Starting Procedure 22-5...
  • Page 36 NOTICE: To avoid sparks near battery, disconnect black jumper cable at point (4) frame before adjusting red cable at point (1). Boost battery Step 3: Start engine. Step 4: Remove cables in REVERSE order and install covers over cable clamps. 22-6 Starting Procedure SC30TX Stump Cutter...

  • Page 37: Shutdown Procedure

    Disengage cutter wheel by releasing Boom Control Lever or disengage the Cutter Wheel Switch. Step 3: Shut engine off and remove key. Step 4: Wait for cutter wheel to stop. NOTICE: To stop cutter wheel quickly, release lever and shut off engine. SC30TX Stump Cutter Shutdown Procedure 23-1...

  • Page 38: Setting Park Brake

    (1) on right side track to engage sprocket. If pin does not go all the way through, push the unit forward or backward slightly until pin will fully engage. Remove pin and place in stow position (2) before moving machine. 23-2 Shutdown Procedure SC30TX Stump Cutter...
  • Page 39 If shutting down on a slope, turn machine to face across the slope to prevent machine from creeping away from the parked position. If this is not possible, position brake actuator (1) in the locked position. SC30TX Stump Cutter Shutdown Procedure 23-3...
  • Page 40 If shutting down on a slope, turn machine to face across the slope to prevent machine from creeping away from the parked position. If this is not possible, position brake actuator (1) in the locked position by moving the actuator by foot. 23-4 Shutdown Procedure SC30TX Stump Cutter...

  • Page 41: Transporting The Machine

    Do not allow anyone to ride on machine. WARNING: Runover can crush.   Keep feet away from tracks.  Step 1: Refer to “Starting Procedure,” page 22-1. Step 2: Increase engine RPM. Refer to “Engine Controls,” page 20-1. SC30TX Stump Cutter Transporting the Machine 30-1...

  • Page 42: Steering The Machine

    Steering the Machine • Refer to “Machine Controls,” page 20-3. Machine - Clean Before Transporting • Clean machine to keep debris off road and from striking other vehicles during transport. 30-2 Transporting the Machine SC30TX Stump Cutter...

  • Page 43: Trailering The Machine

    Set throttle to half speed. Use Propel Lever to move machine. Drive machine squarely onto trailer. Step 5: Step 6: Stop machine when tie-down position is reached. The tie-down position distributes weight on the trailer as recommended by the trailer manufacturer. SC30TX Stump Cutter Transporting the Machine 30-3...

  • Page 44: Unloading

    Starting Procedure, page 22-1. Step 4: Set Throttle to half speed. Step 5: Raise cutter wheel. Step 6: Use Propel Levers to move machine off the trailer. Refer to “Driving the Machine,” page 30-1. 30-4 Transporting the Machine SC30TX Stump Cutter...
  • Page 45 (450 kg). Minimum sling leg length is 6 ft (2 m). Step 4: Use suitable equipment to lift and lower machine onto the transport vehicle. Fasten machine to transport vehicle using tie-downs. Refer to “Trailering the Machine,” page 30-3. SC30TX Stump Cutter Transporting the Machine 30-5...

  • Page 46: Emergency Towing

    (3), and tow machine to transport vehicle. NOTICE: Do not exceed 1–2 mph (2–3 km/h) when towing. After towing, tighten tow valves (1) torque to 9–10 ft-lb  Step 3: (12.2–13.6 Nm). 30-6 Transporting the Machine SC30TX Stump Cutter...

  • Page 47: Preparing Machine And Work Area

    Become familiar with the controls, operation and use of the machine under the supervision of a trained and experienced operator. The operator must be familiar with the workplace’s safety rules and regulations, and must be mentally and physically capable of operating the machine safely. SC30TX Stump Cutter Preparing Machine and Work Area 40-1...

  • Page 48: Personal Protection

    Use eye and face protection.  NOTICE: Face shields must meet ANSI Standard Z87.1 - 2010 ‘Face shields’, and must be marked ‘Z87+’. Face shields are available from various sources, including your local Vermeer dealer. 40-2 Preparing Machine and Work Area SC30TX Stump Cutter...

  • Page 49: Sound And Vibration Levels

    NOTICE: The stated sound levels are representative for a given operating condition. Operating conditions may vary at each jobsite. The actual sound levels for your application and operating conditions may be different. SC30TX Stump Cutter Preparing Machine and Work Area 40-3...

  • Page 50: Operator Presence Switch - Check

    Boom Control Lever to re-engage the cutter wheel. The Operator Presence system is intended for your safety and must be maintained in good functional condition. Contact your Vermeer dealer if it does not function properly. REPARE THE WARNING: Keep spectators away....

  • Page 51: Underground Utility Contact

    Electric Green/Brown Sewer Yellow Gas, Oil or Petroleum White Proposed Excavation Orange Communication, Telephone, TV Pink Surveying Blue Potable Water SC30TX Stump Cutter Preparing Machine and Work Area 40-5...

  • Page 52: Look For Evidence Of Underground Placement

    If the utility cannot be precisely located, it must be shut off by the utility company. Look for Evidence of Underground Placement Visually check for: • notices of underground placements • manhole covers • drop boxes • recent trenching activity 40-6 Preparing Machine and Work Area SC30TX Stump Cutter...
  • Page 53 Do not operate this machine in an area with flammable dust or vapors. Carbon monoxide fumes from the engine can asphyxiate. Operate only outdoors or provide adequate ventilation if indoor operation is essential. SC30TX Stump Cutter Preparing Machine and Work Area 40-7...

  • Page 54: Prepare The Machine

    Keep pressure washer stream away from machine controls and electrical/electronic devices. Compressed air can also push moisture through some connector and component seals. Do not point air nozzle directly at seal areas. 40-8 Preparing Machine and Work Area SC30TX Stump Cutter...

  • Page 55: Fuel Tank - Fill

    (C) Remove the fuel cap. (D) Keep the fuel nozzle or spout in contact with the tank neck while fueling to help prevent static electric buildup. SC30TX Stump Cutter Preparing Machine and Work Area 40-9...
  • Page 56 Unlock fuel cap with supplied key (European only). Fill fuel tank at the end of each day to prevent condensation. Do not fill tank to the very top; leave room for expansion. Fill Cap Fuel Gauge 40-10 Preparing Machine and Work Area SC30TX Stump Cutter...

  • Page 57: Engine System - Check

    NOTICE: Engine is equipped with oil pressure switch. When oil pressure decreases below an acceptable level, the engine will shut off. Keep engine oil fill cap (3) tight and dipstick (2) in place while engine is running. SC30TX Stump Cutter Preparing Machine and Work Area 40-11...

  • Page 58: Hydraulic Fluid Level - Check/Add Fluid

    Refer to the Maintenance Manual, “Specifications” section, for information on hydraulic oil. NOTICE: The hydraulic fluid must be free of bubbles. Bubbles are trapped air that is entering the hydraulic system. 40-12 Preparing Machine and Work Area SC30TX Stump Cutter...

  • Page 59: Operating The Machine

    Remove loose chunks of wood, secondary growth, stones, wire, and other debris from stump and work area.   Wear hard hat, eye protection, and face shield.  WARNING: Thrown objects from rotating cutter wheel can injure others.  Keep cutter wheel down and spectators away. SC30TX Stump Cutter Operating the Machine 50-1...

  • Page 60: Cutter Wheel Guard

    The cutter wheel guard (1) pivots to allow it to float over obstructions. Never secure guard in the raised position while cutting a stump. WARNING: Never work on or near the cutter wheel unless the engine is shut off and the cutter wheel stopped. 50-2 Operating the Machine SC30TX Stump Cutter...

  • Page 61: Runover/Rollover Prevention

    If machine must be transported across a slope where sideways rollover is possible, operate in a direction which places the operator on the uphill side of the machine. • Never ride on machine when operating ground drive system. SC30TX Stump Cutter Operating the Machine 50-3...

  • Page 62: Operator Presence System

    When stepping away from the machine, ensure that no vegetation or other objects are in contact with the levers. The Operator Presence system is intended to help protect the operator and must be maintained in good working condition. 50-4 Operating the Machine SC30TX Stump Cutter...

  • Page 63: Machine Operation

    With engine at low speed and hand on the Boom Control Lever (1), push Cutter Wheel Drive Switch (2) to engage the cutter wheel. Step 3: Move Throttle Control Lever forward (3) to maximum engine RPM. SC30TX Stump Cutter Operating the Machine 50-5...
  • Page 64 Cutting from the top also tends to pull the machine over the stump. Position machine with cutter wheel Step 4: centered and near front top edge of stump as shown. 50-6 Operating the Machine SC30TX Stump Cutter...
  • Page 65 SmartSweep system monitors engine speed and adjusts swing speed by varying hydraulic oil flow to the swing system to maintain engine RPM in the operating range. Repeat previous step until you have cut approximately 10" (25 cm) of the stump or removed stump Step 7: down to ground level. SC30TX Stump Cutter Operating the Machine 50-7...

  • Page 66: Engine Operating Angle

    NOTICE: Engine operating angles do not indicate safe machine operating angles. The engine may run continuously up to 25°. If the engine is operated more than 3 minutes outside acceptable angle limits, engine damage may result. 50-8 Operating the Machine SC30TX Stump Cutter...

  • Page 67: Removing Chips

    Step 2: Follow Shutdown Procedure, page 23-1. Step 3: Clear chips with a rake or shovel. Move machine back into position. Step 4: • When the cutting operation is complete, follow shutdown Procedure. SC30TX Stump Cutter Operating the Machine 50-9...
  • Page 68 This page intentionally left blank.

  • Page 69: Maintenance Intervals

    Follow Shutdown Procedure, page 23-1. Visually inspect machine daily before starting the machine. Make no modifications to your equipment unless specifically recommended or requested by Vermeer Corporation. AFETY IGNS Safety signs located on your machine contain important and useful information that will help you operate your equipment safely.

  • Page 70: Maintenance Manual

    For example, at 100 service hours, display will flash “oil change.” To reset display, place tip of included wand (2) against dot (3). In several seconds the display will stop flashing. 60-2 Maintenance Intervals SC30TX Stump Cutter...

  • Page 71: Maintenance Intervals

    NTERVALS = Initial maintenance on new machine. Regular maintenance interval may be different. Initial = Regular maintenance interval. For Vermeer maintenance replacement part numbers, refer to the Parts Manual or call your Vermeer dealer. Maintenance Interval - Service Hours 10 or...
  • Page 72 Hydraulic Fluid Tank - Fill  Hydraulic System - Restore/Charge Pressure Check  Battery Electrolyte Levels/Terminals - Check/Clean  Battery - Replace  Cutter Teeth/Pocket - Replace  Tracks - Adjust/Remove/Replace/Install  Air Cleaner Element - Replace 60-4 Maintenance Intervals SC30TX Stump Cutter...
  • Page 73 Maintenance Interval - Service Hours 10 or 500 or Service Each Use Yearly Required  Containment Curtain - Replace SC30TX Stump Cutter Maintenance Intervals 60-5...
  • Page 74 This page intentionally left blank.

  • Page 75: Index

    Engine System - Check, 40-11 Machine - Clean Before Transporting, 30-2 Engine, 22-3 Machine Controls, 20-3 Machine Identification Decal, v Machine Identification Numbers - Record, iv Fuel Tank - Fill, 40-9 Machine Operation, 50-5 Maintenance Intervals, 60-1 Maintenance Intervals, 60-3 SC30TX Stump Cutter Index...
  • Page 76 Receiving and Delivery Report, i Removing Chips, 50-9 Runover/Rollover Prevention, 50-3 Safety Messages, 10-1 Safety Signs, 60-1 Safety Symbol Explanation, 10-1 Setting Park Brake, 23-2 Shutdown Procedure, 23-1 Sound and Vibration Levels, 40-3 Starting Procedure, 22-1 Starting the Engine, 22-1 Index SC30TX Stump Cutter...
  • Page 77 09/14 Introduction, 10-4,23-2, 23-3, 23-4, 40-9, 40-10 Updated park brake instructions for all model styles. o1_04 05/15 10-1, 30-5, 40-3, 50-7,60-3, Added alert symbol, updated to SmartSweep, added 3 point lift, added linkage oiling. SC30TX Stump Cutter Revision History...
  • Page 78 The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Copyright 2013, 2014, 2015. All rights reserved. Vermeer Corporation 1210 Vermeer Road East, P.O. Box 200 Pella, Iowa 50219-0200...

Table of Contents

Save PDF