Advertisement
Quick Links
Advertisement
Related Manuals for aivituvin AIR 38
Summary of Contents for aivituvin AIR 38
- Page 1 INSTRUCTION MANUAL AIR 38 www.aivituvin.com...
- Page 3 NOTICE Please retain these instructions for future reference. Firmly secure all bolts,screws and knobs before use. Reconfirm that all bolts,screws,and knobs are secure every 90 days. Fasten screws loosely during initial assembly. Do not fully tighten screws until the item is completely assembled. Do not use or store this item in the proximity of open flame or flammable/combustible chemicals.
-
Page 4: Tools Required
TOOLS REQUIRED PHILLIPS DRILL 2PERSON APPROXIMATELY SCREWDRIVER (RECOMMENDED) ASSEMBLY 45MIN. ASSEMBLY HARDWARE M3.5x40mm SCREW M3.5x60mm SCREW 6PCS+1spare 18PCS+1 spare M3.5x25mm SCREW M3.0x16mm SCREW 36PCS+1 spare 14PCS+1 spare Chewing Toy for Gift Bowl M3.0x16mm SCREW Lock 6PCS+1 spare 1PCS... - Page 5 PARTS Front panel of small house Back panel of small house Side panels of small 2PCS Back Panel-Upper Top panel of small housel Front Panel-Upper Layer Right Panel-Upper Left Panel-Upper 4PCS...
- Page 6 PARTS Fence Ramp Front Panel-Lower 4PCS 4PCS Right Panel-Lower Back Panel-Lower Left Panel-Lower Layer Caster Caster with brake 2PCS 2PCS...
- Page 7 PARTS Bottom Layer Roof Tray...
-
Page 8: Product Assembly
PRODUCT ASSEMBLY Attach the small house,attach the Part A,B,C & D by 12XP3 screws. Attach upper parts,attach the Part E, F,G & H by 8xP2 screws. - Page 9 PRODUCT ASSEMBLY ① Screw the fence Part J to layer Part I from the bottom by 2xP3 screws each piece. (Pls pay attention to the position of Part J of 2 layers). Put the Part I inside house. ② Attach the ramp Part K to layer by 2XP4screws.
- Page 10 PRODUCT ASSEMBLY ① Attach lower parts,attach the Part L, M, N & O by 10XP2 screws. ② Attached the caster 2x Part P by 8XP3 screws. Attached the Caster with brake 2x Part Q by 8XP3 screws. Q x2...
- Page 11 PRODUCT ASSEMBLY ① Screw the fence Part J to layer Part I from the bottom by 2XP3 screws each piece. (Pls pay attention to the position of Part J of 2 layers) ② Put the Part I & R inside house. Attach the ramp 2x Part K to layer by 2XP4 screws each piece.
- Page 12 PRODUCT ASSEMBLY Attach the upper part and lower part by 6XP1 screws. (Pls pay attention the position of the upper and lower) Attach the ramp Part K to layer by 2XP4 screws .
- Page 13 PRODUCT ASSEMBLY Attached the roof Part S by 6XP8 screws. Put in the bottom layer Part U.
- Page 14 PRODUCT ASSEMBLY Put in the tray Part V above the bottom layer. Put in the small house,P5 & P6 inside the hutch anywhere you want.
- Page 15 PRODUCT ASSEMBLY Screw the latch P7 by 4XP4 screws on roof and tray position. Finish...
- Page 16 WARNING Manufacturer and seller expressly disclaim any and all liability for personal injury,property damage or lo ss,whe ther direct ,indir ect,or incid ental ,resul ting f rom th e inc orrect attachment,improper use,inadequate miantenance,or neglect of this product.
Need help?
Do you have a question about the AIR 38 and is the answer not in the manual?
Questions and answers