Installation; How To Use; Care And Maintenance - Dreame R10 Pro User Manual

EN 7.Antistatic Contact
8.Charging Port
9.LED Battery Status
Indicator
10. Battery Release Button
11. • Press to turn on On/Off Switch
• Release to turn off
12.Dust Cup
13.Dust Cup Bottom Cover Release
Button
14.Brush Release Button
Fig. B

Installation

Fig. C-1
Wall Mount Installation
Diagram
1. Paste the mounting template sticker on
the wall. The bottom edge of the
mounting template sticker should be
parallel to and about 107cm from the
ground.
2. Use a power drill with an 8 mm drill bit
to drill a hole into each marker on the
mounting template sticker, then insert a
wall plug into each hole.
3. Align the holes on the mount with the
holes on the wall. Fasten it to the wall
with the included screws.
Fig. C-2
Note:
• The wall mount is an optional accessory.
You can install it based on your needs.
• The wall mount should be installed on a
cool, dry surface with an electrical outlet
nearby. Prior to installing, ensure that there
are no electrical wires or pipes in the space
directly behind installment position.
Charging
Fully charge the vacuum before using it for
the first time.
35
Note:
• A full charge will take approximately 4
hours.
• Using Turbo mode for a prolonged period
will cause the battery to heat up, which
increases charging time. Allow the vacuum
to cool down for 30 minutes before
charging it.
Charging Methods
Charging the vacuum with the charger
Fig. D-1
LED Battery Status Indicator
Low battery
Half battery
Nearly full
Fully charged
Off Blinking On
Note: Once the vacuum is fully charged, the
indicator will turn off after 5 minutes, and
the vacuum will enter the energy-saving
mode.
Fig. D-2

How to Use

Working Methods
Select from two working methods for the
vacuum, based on your needs.
Method 1: Discontinuous Cleaning Mode
Press and hold the on/off switch to power it
on, and release it to stop immediately.
Fig.E-1
Method 2: Continuous Cleaning Mode
(Trigger switch lock)
Click the trigger switch lock to switch
to Continuous Cleaning Mode when the
vacuum is running. Then release the on/off
switch to make the vacuum in Continuous
Cleaning Mode.
Use the trigger switch lock to free your
fingers and avoid finger fatigue caused
by holding the switch.
Fig. D-2
Note:
• In this mode, the lock indicator will
illuminate steadily.
• Click the trigger switch lock again to
quit the Continuous Cleaning Mode.
Using Different Accessories
Multi-Surface Brush
- When using on baby play mats, carpets
or for vacuuming coffee beans, pop corn
and other pellets, turn on the switch on the
brush.
- When vacuuming on tiles, wooden floors
or other hard surfaces, turn off the switch.
Fig. E-3
Note:
• The multi-surface brush can be attached
directly to the vacuum.
• When the appliance starts, the lights in
front of the brush roller will automatically
turn on, which is convenient for use.
Motorized Mini-Brush
For vacuuming dirt, pet hair, and other
stubborn debris from sofas, bedding, and
other fabric surfaces.
Fig. E-4
Note: It is not recommended to vacuum on
fragile surfaces, such as silk.
Soft Roller Brush
Suitable for cleaning hard floors such as
marbles and tiles.
Fig. E-5
Note: The soft roller brush can be attached
directly to the vacuum.
Wide Combination Tool
For vacuuming curtains, keyboards, ceilings,
sofas, vehicle interiors, coffee tables, etc.
Fig. E-6
Flexible Combination Tool
Bendable and retractable brush-nozzle,
more flexible to vacuum in narrow gaps.
Fig. E-7
Wall Mount
The vacuum cleaner can be placed on
the wall mount when it is not in use.
Note:
• Do not put the vacuum cleaner alone
on the wall mount.
• Place it on the wall mount after
connecting it with the extension rod
and the multi-surface brush.
Fig. E-8
Note:
• If any rotating part becomes stuck, the
vacuum may shut off automatically.
Remove any trapped foreign objects, then
resume use.
• When the motor becomes overheated,
the vacuum will automatically shut off.
Wait until the battery temperature returns
to normal, then resume use.
Care & Maintenance
Tips:
1. Always use genuine parts to keep your
warranty from being void.
2. If the filter or nozzle becomes clogged,
the vacuum will stop working shortly
after being turned on. Clear the tube to
restore functionality.
3. If the vacuum is not used for an
extended period, fully charge it, unplug
its charger, and store it in a cool, low-
humidity environment away from direct
sunlight. To avoid over-discharging the
battery, recharge the vacuum at least
once every three months.
Cleaning the Vacuum
Wipe the vacuum with a soft dry cloth.
EN
36