ECOVACS DEEBOT 601 - Robot Vacuum Cleaner Manual

ECOVACS DEEBOT 601 - Robot Vacuum Cleaner Manual

Also See for DEEBOT 601:

Advertisement

ECOVACS DEEBOT 601 - Robot Vacuum Cleaner Manual

Package Contents

Note: Figures and illustrations are for reference only and may differ from actual product appearance. Product design and specifications are subject to changes without notice.

Product Diagram

Main Unit

Product Diagram - Main Unit

Bottom View

Product Diagram - Bottom View

Charging Dock

Product Diagram - Charging Dock

Remote Control

Product Diagram - Remote Control

Operating and Programming

Notes Before Cleaning


Do not use DEEBOT on wet surfaces or surfaces with standing water.


Before using the product on a rug with tasseled edges, please fold the rug edges under.

Notes Before Cleaning - Placing a physical barrier
It may be necessary to place a physical barrier at the edge of a drop to stop the unit from falling over the edge.

Notes Before Cleaning - Tidying up the furniture
Tidy up the area to be cleaned by putting furniture, such as chairs, in their proper place.


Remove power cords and small objects from the floor that the robot could be obstructed by.

Preparation

  1. Plug in Adapter
  2. Charging Dock Placement
  3. Install Side Brushes
  4. Power ON
  5. Charge DEEBOT
    Preparation - Charging the unit

Note: When DEEBOT completes the cleaning cycle or when battery power gets low, DEEBOT automatically returns to the Charging Dock to recharge itself.

Selecting Cleaning Mode

  1. AUTO Cleaning Mode
    A Random Cleaning Pattern (optimized for carpets) will be selected by default.
    Selecting Auto Cleaning mode - Random pattern
    To switch to a Programmed Cleaning Pattern (optimized for hard floors) or switch between these two patterns, perform the following action:
    Selecting Auto Cleaning mode - Programmed pattern
    Note: Cleaning pattern cannot be switched until DEEBOT is paused or charging. DEEBOT will start a new cleaning cycle once cleaning pattern is switched. will light up once Programmed Cleaning Pattern is enabled.
  2. Spot Cleaning Mode (Less than 3 minutes)
    Selecting Cleaning mode - Spot Cleaning mode
  3. Return to Charging Dock
    Selecting Cleaning mode - Return to charging dock

All the functions mentioned above can be enabled on the App. Download ECOVACS App to access more features, including Edge Cleaning, Scheduled Cleaning, etc.

www.apple.com

play.google.com

Pause, Wake Up, Power Off

  1. Pause
    Note: The robot's Control Panel stops glowing after the robot is paused for a few minutes. Press the AUTO Mode Button on DEEBOT to wake up the robot.
    Operating and Programming - Pause
  2. Wake Up
    Press the AUTO button on DEEBOT to wake it up

    Operating and Programming - Wake up
  3. Power OFF
    Note: When DEEBOT is not working, it is recommended to keep it switched ON and charging.

Maintenance

Before performing cleaning and maintenance tasks on DEEBOT, turn the robot OFF and unplug the Charging Dock.

Dust Bin and Filters

Dust Bin Parts
Dust Bin

Maintenance - Dust Bin and Filters

Main Brush

Note: A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.
Maintenance - Main Brush

Side Brushes

Maintenance - Side Brushes

Other Components

Maintenance - Other Components

Note: Before cleaning the robot's Charging Contacts and Charging Dock Pins, turn the robot OFF and unplug the Charging Dock.
Maintenance - Cleaning precaution

Regular Maintenance

To keep DEEBOT running at peak performance, perform maintenance tasks and replace parts with the following frequencies:

Robot Part Maintenance Frequency Replacement Frequency
Side Brush Once every 2 weeks Every 3-6 months
Main Brush Once per week Every 6-12 months
Sponge Filter/ High Efficiency Filter Once per week Every 3-6 months
Universal Wheel
Anti-Drop Sensors
Bumper
Charging Contacts
Charging Dock Pins
Once per week /

A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.
Note: ECOVACS manufactures various replacement parts and fittings. Please contact Customer Service for more information on replacement parts.

Indicator Light and Alarm Sounds

DEEBOT will tell you something is wrong with an alarm indicator light and sounds. More detailed support is available through the ECOVACS App and online website.

Indicator Light
Scenario Indicator Light
The robot is charging AUTO Mode Button flashes WHITE
The robot is cleaning AUTO Mode Button glows a solid WHITE
The robot has low battery AUTO Mode Button glows a solid RED
The robot has a problem AUTO Mode Button flashes RED
Programmed Cleaning Pattern is enabled Cleaning Mode Switch Indicator lights up
Alarm Sounds
Alarm Sound Problems Solution
One Beep Main Brush or Side Brush is tangled. Clean Main Brush or Side Brush as mentioned in Maintenance Section.
Two Beeps Anti-Drop Sensor Malfunction Use a cleaning cloth to wipe the Anti-Drop Sensor clean.
Three Beeps Dust Bin is not properly installed. Make sure the Dust Bin has been installed; if it has, take it out and put it back in properly.
Continuous Beeps The Robot is suspended or the Driving Wheels are tangled. Put the Robot back on the ground or gently pat the bumper and clean the Driving Wheel as mentioned in Maintenance Section.

Troubleshooting

No. Malfunction Possible Causes Solutions
1

The unit is not charging

DEEBOT is not switched ON. Switch ON DEEBOT.
DEEBOT has not connected to the Charging Dock. Be sure that the robot's Charging Contacts have connected to the Charging Dock Pins.
The battery is completely discharged. Re-activate the battery. Switch ON DEEBOT. Place DEEBOT on the Charging Dock by hand, remove after charging for 3 minutes, repeat 3 times; then charge normally.
2

The unit cannot return to the Charging Dock

The Charging Dock is not correctly placed. Refer to Preparation section to correctly place the Charging Dock.
3

Device gets stuck while working and stops

DEEBOT is tangled with something on the floor (electrical wires, curtains, carpet fringing, etc.). DEEBOT will try various ways to free itself. If it is unsuccessful, manually remove the obstacles and restart.
4 DEEBOT returns to the Charging Dock before it has finished cleaning When the battery gets low, DEEBOT automatically switches to Return to Charger Mode and returns to the Charging Dock to recharge itself. This is normal. No solution necessary.
Working time varies according to floor surface, room complexity and the Cleaning Mode selected. This is normal. No solution necessary.
5

Device does not clean automatically at the scheduled time

Time Scheduling function is cancelled. Program DEEBOT to clean at specific times using the ECOVACS App.
The Continued Cleaning function is turned ON and DEEBOT has just finished cleaning the scheduled cleaning area. This is normal. No solution necessary.
DEEBOT is switched OFF. Switch ON DEEBOT.
The robot's battery is low. Keep DEEBOT switched ON and connected to the Charging Dock to make sure it has a full battery to work at any time.
The robot's Suction Intake is blocked and/or there is debris stuck in its components. Power OFF DEEBOT, clean the Dust Bin and invert the robot. Clean the robot's Suction Intake, Side Brushes and the Main Brush as described in Maintenance Section.
6

Device does not clean the whole area

The cleaning area is not tidy. Remove small objects from the floor and tidy up the cleaning area before DEEBOT starts cleaning.
7 DEEBOT is not able to connect to the home Wi-Fi network Incorrect home Wi-Fi username or password entered. Enter the correct home Wi-Fi username and password.
DEEBOT is not within range of your home Wi-Fi signal. Make sure DEEBOT is within range of your home Wi-Fi signal.
Network setup started before DEEBOT was ready. Turn ON Power Switch. Press the RESET Button for 3 seconds. DEEBOT is ready for network setup when it plays a musical tune and its Wi-Fi Indicator light flashes slowly.
Your smartphone's operating system needs to be updated. Update your smartphone's operating system. The ECOVACS App runs on iOS 9.0 and above, Android 4.0 and above.

Technical Specifications

Model DO3G.11
Working voltage 14.4V DC Rated power 25W
Charging Dock
Rated Input Voltage 19V DC Rated output current 0.6A
Power Adapter Model DK18-190060H-U
Rated Input Voltage 100-120V AC Rated Input Current 0.5A
Rated output Voltage 19V DC Rated output current 0.6A
Remote Control Model RC1633A Input Voltage 3V DC
Battery Lithium 2600mAh

Note: Technical and design specifications may be changed for continuous product improvement.

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download ECOVACS DEEBOT 601 - Robot Vacuum Cleaner Manual

Advertisement

Need help?

Need help?

Do you have a question about the DEEBOT 601 and is the answer not in the manual?

Questions and answers

Table of Contents