Hayward OmniLogic HLBASE Installation Manual
  1. Manuals
  2. Brands
  3. Hayward Manuals
  4. Control Systems
  5. OmniLogic HLBASE
  6. Installation manual

Hayward OmniLogic HLBASE Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OmniLogic
Automation and Chlorination
Installation Manual
HLBASE
Hayward Industries
1415 Vantage Park Dr., Suite 400
Charlotte, NC 28203
Phone: (908) 355-7995
www.hayward.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
®
Contents
Before You Begin.........................1
Overview....................................1
Mounting Equipment..................4
Plumbing...................................6
Wiring.......................................10
System Startup.........................22
Configuration............................23
092472 RevL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OmniLogic HLBASE and is the answer not in the manual?

Questions and answers

Related Manuals for Hayward OmniLogic HLBASE

Summary of Contents for Hayward OmniLogic HLBASE

  • Page 1: Table Of Contents

    Automation and Chlorination Installation Manual Contents Before You Begin......1 Overview........1 Mounting Equipment....4 Plumbing........6 Wiring........10 Preparing Pool/Spa Water..20 System Startup......22 Configuration......23 HLBASE Hayward Industries 1415 Vantage Park Dr., Suite 400 Charlotte, NC 28203 Phone: (908) 355-7995 www.hayward.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 2 3 meters of the pool, spa or hot tub shall be bonded to the equip- ment grounding bus with copper conductors not smaller than 8 AWG US / 6 AWG Canada. SAVE THESE INSTRUCTIONS • USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 3 (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Hayward could void the user’s authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
  • Page 4 System Startup...............22 Startup and Startup and Configuration Wizard........23 Configuration Bodies of Water............24 Filter Pumps............25 Heaters.............26 Chillers..............28 HL-CHEM............28 Chlorinator............28 Cleaners............29 Water Features..........30 Lights..............31 Accessories............32 Shared Equipment..........33 Sensors..............34 Backyard Accessories..........35 Interlocks..............35 Quick Edit..............36 Warranty OmniLogic Limited Warranty..........45 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 5: Before You Begin

    Overview The functions and features described in this manual assume that the OmniLogic is using the latest firmware version available from Hayward. The OmniLogic HLBASE is a multifunction pool automation control that is expandable to meet all your needs and fully manage your pool/spa system. The OmniLogic can control pumps, valves, lighting, heaters, pool chemistry and more.
  • Page 6 Features The standard Hayward HLBASE OmniLogic offers the following features: • control up to 4 (expandable to 10) high voltage (120/240V) relays to control pumps, pool lights, yard lights, water features, chemical dispensers and more • control up to 4 (expandable to 8) automatic valve actuators including pool and spa valves, water feature valves, cleaner valves and more •...

  • Page 7: Installation Steps

    NOTE: If replacing a Pro Logic Controller using networked ColorLogic Lights, the lights must be put into “Standalone” (default) mode before disconnecting the Pro Logic. The OmniLogic can only control ColorLogic lights in “Standalone” mode. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 8: Mounting Equipment

    When selecting a location, note that the standard cables supplied with the included flow switch and temperature sensors, as well as optional accessories like Hayward TurboCells and actuators are all 15 ft. (5m) long. Try to mount the OmniLogic at a height where the touchscreen can be accessed easily.

  • Page 9: Temperature Sensors

    The OmniLogic model requires the use of a chlorinator cell and plumbing kit to provide pool chlorination. These items are not included with the OmniLogic and can be purchased separately at your local Hayward dealer. Choose a chlorinator cell model based on the size of your pool; models are shown below. In addition to the chlorinator cell, a plumbing kit (P-KIT) must be purchased.

  • Page 10: Plumbing

    IN-FLOOR SPA JET PUMP CLEANER PUMP POP-UP SKIM OVERFLOW RETURN SPILLOVER VALVE PUMP WATER WATER POOL FEATURE FEATURE POP-UP POP-UP MAIN DRAIN ENERGY NON-BOOST SUCTION SAVER CLEANER PRESSURE PRESSURE PRESSURE CLEANER CLEANER CLEANER POP-UP USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 11 The water sensor should be installed on the pool loop prior to the heater and will display the pool temperature whenever the “Pool Filter” pump is running. The dual equipment spa sensor should be installed on the spa loop prior to the heater and will display the spa temperature whenever the “Spa Filter” pump is running. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 12 “Pool Filter” pump is on and the system is in the “pool only” operating mode. The plumbing diagram on page 6 is intended to be used as a general guideline and is not a complete plumbing schematic for the pool. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 13: Turbocell

    Flow Switch (supplied with P-KIT) A Hayward flow switch is required if using the optional TurboCell for chlorination, a liquid chlorine dispenser, chlorine tablet feeder or an AQL-CHEM2 for pH dispensing. The flow switch is a safety device that ensures that water is flowing before the OmniLogic starts to generate/dispense chlorine or dispenses acid. It must be plumbed in the same section of plumbing as the TurboCell or dispenser.

  • Page 14: Wiring

    -Ensure that Power is disconnected prior to performing any wiring -Follow all local and NEC (CEC if applicable) codes -Use copper conductors only -Remove power to the OmniLogic subpanel before removing the deadfront HLWLAN Power USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 15: Main Service

    The OmniLogic requires 120VAC, 5A power to operate the control logic circuits and the chlorinator. This power should be connected to a dedicated circuit breaker. WARNING: 120VAC only (permanent damage will occur if connected to 240V) USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 16: Pool Equipment Connection Table

    After attaching equipment to the OmniLogic, fill in the appropriate information in the table. Connection Table HVR8 HVR5 HVR6 HVR7 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 17: High Voltage Pool Equipment

    Requires two relays for proper operation of both speeds. NOTE: When selecting relays for two speed operation, note that both relays must be within the Relay Bank (HLRELAYBANK) or neither relay should be within the Relay Bank. The diagram below shows the pump connected to relays outside of the Relay Bank. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 18: Low Voltage Wiring

    Speed Pump. Valve Actuators The OmniLogic HLBASE can control up to four automatic valve actuators. When used with the op- tional Input/Output Expander Board (HLIOEXPAND), up to 8 valve actuators can be used. Two of the valve outputs are normally used for the pool/spa suction (Valve2) and return (Valve1) valves. Valve3 and Valve4 are for general purpose use (solar, water feature, in-floor cleaner, etc.).
  • Page 19 (usually identified as “2-wire” remote control). For millivolt or line voltage heaters, contact Hayward Tech support, 908-355-7995. Refer to the diagram on page 12 for the location of heater connections (LVR) on the OmniLogic Main Board.
  • Page 20 Smart Heaters are programmed with a Hayward Unique Address (HUA) which allows it to be fully controlled by a Hayward Omni pool automation control. Similar to other Smart Devices such as select Hayward variable speed pumps, you will be able to remotely create schedules and setpoints for both heating and cooling while displaying real time heater status and diagnostics for the Smart Heater.
  • Page 21 If both solar and dual equipment are desired, another temperature sensor must be purchased separately. The sensors are provided with a 15 ft. cable. If a longer cable is required, contact the Hayward service dept. (908-355-7995) for information on suitable cable types and splices.
  • Page 22 Plug in the connector from the HL-CHEM into one of the Low Speed Bus connectors on the main PCB in the OmniLogic Control Center as shown below. Refer to the HL-CHEM manual for complete installation instructions. Connect Probe Cell cable here Route cable through access hole Route though knockout USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 23 The HLWLAN can be mounted up to 25ft away from the OmniLogic and requires an ethernet connection to the OmniLogic, a power connection to the Omni- Logic’s Main Board, and a 2.4GHz connection to the router. Refer to the HLWLAN manual for detailed installation instructions. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 24: Preparing Pool/Spa Water

    Salt Chlorination When used with an optional Hayward TurboCell and P-KIT, the OmniLogic can generate all the chlorine needs for pools up to 40,000 gallons (150,000 liters), or the needs of most commercial pools up to 25,000 gallons (95,000 liters). If enabled (see Configuration Wizard), this operation requires a low concentration of salt (sodium chloride) in the pool/spa water.

  • Page 25: Salt

    A high salt level can cause the OmniLogic to stop chlorinating. The salt in your pool/spa is constantly recycled and the loss of salt throughout the swimming season should be minimal. This loss is due primarily to the addition of water because of splashing, backwashing, or draining (because of rain). Salt is not lost due to evaporation. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 26: System Startup

    The OmniLogic’s firmware is the basic operating system that runs the unit. The OmniLogic was shipped with the version of firmware that was available at the time of release. There may be a newer version available and if so, we encourage you to upgrade. Also, if you have experienced problems, Hayward Technical Support may advise you to upgrade your OmniLogic firmware.

  • Page 27: Configuration

    In this case, a keyboard will be displayed and you’ll be able to type the desired name. After naming the equipment, save then advance. This method is repeated throughout the Configuration Wizard. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 28: Bodies Of Water

    Would You Like To Set Up A Network Connection Now? - You can select whether to connect to the internet through a wired connection (requires ethernet connection shown on page 19) or wireless (requires the use of a Hayward HLWLAN wireless transceiver with a 2.4GHz connection to the router). If no connection is desired or you will be setting up the connection later, select “not now”.

  • Page 29: Filter Pumps

    If VSP is selected: Which Hayward Unique Address? If using a VSP, you’ll be asked what is the Hayward Unique Address (HUA). If a value is already shown in the box, advance to the next screen. If no value is shown, selecting the box will bring you to a table showing all detected devices.

  • Page 30: Heaters

    If Yes is selected: Which Hayward Unique Address? Select the HUA of the Smart Heater that you would like to configure. Name Heater Select the box, then type the desired name for your heater. This name will be used when referring to this particular heater.
  • Page 31 Where is the Solar Temperature Sensor Located? Selecting the box will bring you to a table showing all detected sensors. Select the solar sensor (usually SENS3), then advance. The sensor should now be shown in the box. Advance to the next screen to continue solar heater configuration. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 32: Chillers

    Which Hayward Unique Address? If a Hayward Unique Address (HUA) is already shown in the box, touch the Advance button. If no address is shown, selecting the box will bring you to a table showing all detected Sense and Dispense devices. Select the HL-CHEM from the table and touch the Done button to advance.

  • Page 33: Cleaners

    Where is the Valve Wired? - Selecting the box will bring you to a table showing all valve outputs. Find the valve that is connected to the Tablet Feeder. Select the valve and select Done. If No is selected: Do You Have a Salt Water Chlorine Generator? (requires a connected Hayward TurboCell or AquaRite with HLAQRPCB communica- tion board) If Yes is selected: Type of Cell? Select the type of Hayward TurboCell that is installed in your system.

  • Page 34: Water Features

    If VSP is selected: Which Hayward Unique Address? If using a VSP for your cleaner pump, you’ll be asked what is the Hayward Unique Address (HUA). If a value is already shown in the box, advance to the next screen. If no value is shown, selecting the box will bring you to a table showing all detected devices.

  • Page 35: Lights

    If VSP is selected: Which Hayward Unique Address? If using a VSP for your water feature pump, you’ll be asked what is the Hayward Unique Address (HUA). If a value is already shown in the box, advance to the next screen. If no value is shown, selecting the box will bring you to a table showing all detected devices.

  • Page 36: Accessories

    If VSP is selected: Which Hayward Unique Address? If using a VSP for your accessory pump, you’ll be asked what is the Hayward Unique Address (HUA). If a value is already shown in the box, advance to the next screen. If no value is shown, selecting the box will bring you to a table showing all detected devices.

  • Page 37: Shared Equipment

    Body of Water 1. Do you have Spillover? Select yes to this question if you have Spillover in your system. If yes is selected, choose the valves that will operate Spillover from the following screen. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 38: Sensors

    If your lights blink white after the test, you can enable OmniDirect mode. If not, the UCL light will default to UCL Standalone mode. Note that if you are configuring a WaterBowl light, the Flicker feature will only be available if the light is set to OmniDirect Mode. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 39: Backyard Accessories

    A summary screen will be displayed after configuring this interlock. Read through the description and make sure the interlock will function as desired. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 40: Quick Edit

    This will take you back to the last screen of configurable items for that device. If you would like to continue to make changes, but to a different device, press the Home button and then follow the pathway to the new device. The following pages will explain each configuration pathway. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 41 Type - Change the type of Filter Pump that is configured (Single Speed, 2-Speed, or VSP) HUA - Match the HUA (Hayward Unique Address) to the configured Filter Pump. This option only appears if the Filter Pump is configured as a Variable Speed Pump.
  • Page 42 If Cleaners is selected: Add Cleaner - Pressing “Add Cleaner” from this screen will take you through the full configuration for adding a new cleaner. These steps are described in the Configuration Wizard portion of this manual. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 43 Add Standalone Light - Pressing “Add Standalone Light” from this screen will take you through the full configuration for adding new lights. These steps are described in the Configuration Wizard portion of this manual. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 44 These steps are described in the Configuration Wizard portion of this manual. Select an Existing Group of Lights - Once you select a group of existing lights, all of the options for those lights will appear on the next screen. These options are as follows: USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 45 Would you like to set up a network Connection now? Select the type of connection you would like to setup/modify or select “Not Now”. For wireless connections, you must have a Hayward HLWLAN connected to the OmniLogic. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 46 Configuration Wizard. External Antenna - Make this selection when setting up a Hayward HLWLAN. Note that a 2.4GHz connection to the router is required. Once the system is done running through the diagnostics, press the check mark to continue to the next section of the Configuration Wizard.
  • Page 47 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 48 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 49: Omnilogic Limited Warranty

    Plus and SwimPure chlorination products to be free of defects in materials and workmanship, under normal use and service, for a period of three (3) years. Hayward also warrants its Aqua Trol chlorina- tion products to be free of defects in materials and workmanship, under normal use and service for a period of one (1) year.
  • Page 50 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 51 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 52 Hayward is a registered trademark and OmniLogic is a trademark of Hayward Industries, Inc. © 2023 Hayward Industries, Inc. All other trademarks not owned by Hayward are the property of their respective owners. Hayward is not in any way affiliated with or endorsed by those third parties.

Table of Contents