Whirlpool ADP 6839 Quick Reference Manual

Quick reference guide
PROGRAMME START BUTTON
SELECTION The indicator lights up during operation, flashes when a fault occurs, and goes off
BUTTON at the end of the programme.
(See programme START BUTTON RESET FUNCTION:
chart below) Press this button for at least 2 seconds; the selected programme and options will
be cancelled. Main failure displays (repeated flashing of the START indicator lamp)
can be cancelled by RESETTING. Detailed instructions are given in chapter
"What to do if...".
Table of programmes
P
Programmes
1
Steam Sensor 40-70°C
2
Pre-Wash
3
Glasses
4
Quickwash
5
2)
Eco
6
Antibacterial
7
Overnight
1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary
depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of the appliance's automatic calibration system.
2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the
EN/Standard loading comparison test and other tests, contact the following address: "nk_customer@whirlpool.com".
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
START
DELAY
option
Available
Loading instructions
options
Normally or heavily soiled
crockery, including pots and pans.
Delay Thanks to steam action, soaking or
Multizone hand pre-treatment is no longer
Power Clean needed. In addition hygiene is
ensured due to the high
temperature steam.
Delay
cold
Crockery to be washed later.
Multizone
Delay Light soiling, for example glasses
40°C
Multizone and cups.
Lightly soiled crockery, with no
Delay
40°C
dried-on food. * Use of tablets
Multizone
not recommended.
Delay
50°C
Multizone Normally soiled crockery.
Power Clean
Normally or heavily soiled crockery,
Delay with additional antibacterial wash.
3)
Multizone Programme interruption (e.g. due
Power Clean to door opening) can compromise
elimination of germs.
Normally soiled crockery, gentle and
Delay
55°C
quiet thanks to the lower spray
Multizone
pressure (39 dbA).
BEFORE USING THE APPLIANCE FOR THE
FIRST TIME CAREFULLY READ THIS QUICK
REFERENCE GUIDE AND THE INSTALLATION
INSTRUCTIONS! THE GUARANTEE IS NOT
APPLICABLE IF FAULTS ARE CAUSED BY
INCORRECT USE OF THE APPLIANCE.
Options and display description
SALT INDICATOR
When lit, the salt reservoir
MULTI POWER ON/OFF
needs to be refilled.
ZONE CLEAN BUTTON
option option
(see at right for options description)
Consumption
Detergent
1)
Litres kWh
Minutes RINSE AID INDICATOR
When lit, the rinse aid dispenser
needs to be refilled.
X 7-17 0.99-1.75 65-220
— 4.0 0.03 14
X 10.0 0.85 100 DELAYED START
BUTTON
Press the button
X * 10.0 0.65 30
(repeatedly) to delay the
start of the programme.
Adjustable from 1 to 24
X 11.0 1.05 140
hours. With each press of
the button, the delayed
start indicator increases by
one hour and after 24
X 13.0 1.50 115
restarts from 00. Then
press the START button.
The dishwasher will start
after the set time.
X 13.0 1.20 290
FAULT INDICATION AND WASH TIME DISPLAY
In normal operation it indicates the remaining time
(h:mm), whereas with "Delayed start" selected it
indicates the time remaining until programme start (hh).
If "F.." appears on the display, see chapter "What to do
if...".
HALF LOAD/ POWER CLEAN
MULTIZONE Thanks to the additional
Allows you to choose the power jets this option
washing zones. Press this provides a more intensive
button to select the wash and powerful wash in the
zones: lower rack, in the specific
area.This option is
recommended for washing
both racks
pots and casseroles (see
page 4). Press this button
only upper rack
to activate Power Clean
(the indicator lights up).
only lower rack
ADP 6839 5019 396 01667
Chart
GB -1-