Page 1
RETURN MUTING STANDBY AUDIO/FM MODE STANDBY/ON VOLUME SOURCE DVD DIGITAL CINEMA SYSTEM TH-A30 D I G I T A L RM-STHA30U DVD CINEMA SYSTEM INSTRUCTIONS For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet.
Page 2
Warnings, Cautions and Others / Caution –– STANDBY/ON switch! STANDBY/ON Disconnect the mains plug to shut the power off completely. The STANDBY/ON STANDBY/ON switch in any position does not disconnect the mains line. The power can be remote controlled. CAUTION To reduce the risk of electrical shocks, fire, etc.: 1.
Page 3
IMPORTANT FOR LASER PRODUCTS / REPRODUCTION OF LABELS / 1 CLASSIFICATION LABEL, PLACED ON EXTERIOR 2 WARNING LABEL, PLACED INSIDE THE UNIT SURFACE CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT PRODUCTO LASER CLASE 1 1.
Front Panel STANDBY AUDIO/FM MODE STANDBY/ON VOLUME SOURCE DVD DIGITAL CINEMA SYSTEM TH-A30 D I G I T A L See pages in the parentheses for details. Front Panel 1 STANDBY/ON 7 Remote sensor button and STANDBY lamp (11 – 15) 8 3/8 (play/pause) button (11 –...
MUTING IMPORTANT: If you press VCR CONTROL , this remote control will work ONLY for the JVC’s VCR. When you want to operate the system again, press DVD or FM/AM. ; MUTING button (11, 14) a RETURN button (38, 50, 51)
Page 7
Inside the Cover Inside the Cover 1 Number buttons (32, 38, 46, 54, 55) 2 SLOW button (36, 42) TOP MENU MENU RETURN MUTING 3 ZOOM button (36, 42) 4 ANGLE button (30) 5 REPEAT button (33, 39, 46) 6 A–B REPEAT button (33, 39) SOUND 7 CLEAR button (32, 38, 41) 8 SEARCH button (32, 38, 46)
Getting Started Before Installation Putting Batteries in the Remote Control General Precautions Before using the remote control, put two supplied batteries first. • When using the remote control, aim the remote control directly at • DO NOT insert any metal object into the center unit. the remote sensor on the center unit.
Connecting the FM and AM Antennas If AM reception is poor, connect single vinyl-covered wire (not supplied). AM loop antenna (supplied) If FM reception is poor, connect outdoor FM antenna (not supplied). Snap the tabs on the loop into FM antenna (supplied) the slots of the base to assemble the AM loop antenna.
STANDBY AUDIO/FM MODE STANDBY/ON D I G I T A L VOLUME SOURCE S U R R O U N D DVD DIGITAL CINEMA SYSTEM TH-A30 D I G I T A L Subwoofer Right front speaker Left front speaker...
When setting the speakers Connecting the Speakers To obtain the best possible sound from this system, you need to place all the speakers except the subwoofer at the same distance Connect the satellite speakers and subwoofer to the terminals on the from the listening position with each front faced toward the listener.
Getting Started Connecting Audio/Video Component Turn the power off to all components before connections. Audio component connection Illustrations of the input/output terminals below are typical Connect another component to the center unit with the examples. audio cords. When you connect another component, refer also to its Use the cords supplied with another component or purchase manuals since the terminal name actually printed on the rear them at an electric appliance store.
Page 13
TV connection The S-video cord and the component video cord are not supplied with this system. Use the cords supplied with another components or purchase them at an electric appliance store. Component video cord (not supplied) Composite video cord (supplied) Blue S-video cord (not supplied) Green...
(See the manual supplied with your TV.) • The volume level can be adjusted within 51 steps—“MIN (minimum),” • When you use a JVC’s TV, you can turn on your TV by pressing 01 to 49, and “MAX (maximum).”...
Select an Appropriate Progressive Mode To activate DSP modes Press DSP MODE (or DSP on the front panel). DSP MODE You can select the progressive mode according to the picture type The DSP indicator lights up and the current DSP mode (film or video source).
(See the manual supplied with your TV.) • When you use a JVC’s TV, you can turn on your TV by pressing on the remote control, and select the video input by pressing TV/VIDEO. (If your TV is not a JVC’s, see “Operating Other Manufacturers’...
Note: djust the Volume Before activating DSP mode, adjust the speaker setting to bring out the best performance from this system. To increase the volume, press and hold VOLUME +. For in-depth information about adjusting the speaker setting, see To decrease the volume, press and hold VOLUME –. “Speaker Settings”...
Basic Tuner Operations djust the Volume STANDBY/ON AUDIO STANDBY/ON To increase the volume, press and hold VOLUME +. AUDIO To decrease the volume, press and hold VOLUME –. TV/VIDEO PROGRESSIVE VOLUME TV CHANNEL DISPLAY STEP AUDIO/ SUBTITLE TV VOLUME FM MODE CAUTION: FM/AM FM/AM...
Other Basic Operations • When Dolby Surround activates, the PRO LOGIC indicator PROGRESSIVE lights up on the display. TV/VIDEO PROGRESSIVE TV CHANNEL STEP DISPLAY – For in-depth information about Pro Logic modes, see “Creating AUDIO/ SUBTITLE TV VOLUME FM MODE Realistic Sound Fields”...
TV. In such a case, change the scanning mode to “I–SCAN MODE.” • You can change the color system only when the unit is on To check the compatibility of your TV, contact your local JVC standby. customer service center.
Speaker Settings Setting the Delay Time Adjust the delay time of the sounds from the center speaker and the STANDBY/ON rear speakers, comparing to that of the sounds from the front AUDIO speakers. If the distance to the center speaker* and/or the rear speakers** from your listening point is almost the same as from the TV/VIDEO PROGRESSIVE...
Page 22
Speaker Settings For Dolby Pro Logic: Left front Center speaker Right front speaker speaker Before you start, remember... There is a time limit in doing the following steps. If the setting is Subwoofer canceled before you finish, start from step 1 again. 3.0 m Press AUX to select the external 2.7 m...
Creating Realistic Sound Fields You can use the following surround to reproduce a realistic sound Dolby Pro Logic and Dolby 3 Stereo field. Dolby Surround encoding format records the left front channel, • Digital Multichannel Surround—Dolby Digital and DTS Digital right front channel, center channel, and rear channel signals (total 4 Surround channels) into 2 channels.
Page 24
Creating Realistic Sound Fields I DSP (Digital Signal Processor) Modes To check the speaker connections and settings using the test DSP modes have been designed to create important acoustic tone surround elements. 1. Select and play a DVD encoded with Dolby Digital or DTS Digital Surround.
To adjust the output balance for the front speakers 1) Press SOUND repeatedly until the VCR CHANNEL TUNING SOUND adjustment indication for the front B.SEARCH F.SEARCH speakers appears on the display. • Each time you press the button, the adjustment indication ENTER on the display changes as follows: 00 F 00...
Creating Realistic Sound Fields • Each time you press the button, the adjustment indication on the display changes as follows: FM/AM CONTROL 00 F 00 00 R 00 TUNER PRESET DOWN Normal indication REAR VCR CHANNEL TUNING (canceled) B.SEARCH F.SEARCH 00 F (Front) 00 : To adjust the output balance for the front speakers.
To adjust the output balance for the front Activating Dynamic Range Compression speakers and the rear speakers You can enjoy a powerful sound even at a low volume level by 1) Press SOUND repeatedly until one of SOUND compressing the dynamic range (difference between the maximum the following adjustment indications and minimum sounds).
Creating Realistic Sound Fields Adjusting DSP Modes You can adjust the following settings while activating DSP modes. VCR CHANNEL TUNING It is recommended that you make adjustments from your actual B.SEARCH F.SEARCH listening point while listening to reproduced sounds. – Output balance for the front speakers –...
Page 29
To adjust the output level for the rear speakers To adjust the output balance for the front and the subwoofer speakers and the rear speakers 1) Press SOUND repeatedly to select the SOUND 1) Press SOUND repeatedly until one of SOUND the following adjustment indications “REAR”...
Disc Introduction—DVD/VCD/CD This system has been designed to play back the following discs: DVD, IMPORTANT: Video CD, Super Video CD (SVCD), Audio CD, CD-R, and CD-RW. Before performing any operations, make sure of the following..• This system can also play back MP3 files recorded on CD-Rs and •...
Basic Disc Operations To stop playback for a moment TUNER PRESET Press 3/8. While pausing, the elapsed playing time flashes STANDBY/ON AUDIO on the display. • To resume play, press 3/8 again. TV/VIDEO PROGRESSIVE To go to another chapter or track TV CHANNEL DISPLAY STEP...
DVD Playback Showing the On-Screen Bar You can show the following information on the TV screen while a disc is loaded. STANDBY/ON AUDIO From the remote control ONLY: TV/VIDEO PROGRESSIVE DISPLAY Press DISPLAY. DISPLAY TV CHANNEL DISPLAY STEP • Each time you press the button, the following on- SUBTITLE AUDIO/ SUBTITLE...
Selecting the Subtitles Selecting the Multi-Angle Views While playing back a DVD containing subtitles in different While playing back a DVD containing multi-angle views, you can languages, you can select the subtitle to be displayed on the TV view the same scene at different angles. screen.
DVD Playback Disc Menu-Driven Playback Disc menu-driven playback is possible while playing back a DVD STANDBY/ON with menu (menu may be still pictures or moving pictures AUDIO depending on the disc). TV/VIDEO PROGRESSIVE • When operating a disc using the disc menu, refer also to the instructions supplied for the disc.
Moving to a Particular Portion Directly Searching for a Particular Point You can move to another title, chapter, or particular scene in the You can search for a particular point while playing a disc—Variable chapter directly. Speed Forward/Reverse Search. • No sound comes out during Variable Speed Forward/Reverse Search.
DVD Playback 7 A–B Repeat While playing, you can also select a portion you want to repeat. STANDBY/ON AUDIO • A–B repeat is not performed between different titles. • An interval of more than 5 seconds is required between point A TV/VIDEO PROGRESSIVE and point B.
Programming the Playing Order of the Press 3 or 2 to select a chapter number, then Chapters—Program Play ENTER. • 3 : Increases the number. You can arrange the chapter playback order before you start playing. • 2 : Decreases the number. You can program up to 20 steps.
Page 38
DVD Playback To erase the stored program Press 0 to eject the disc. STANDBY/ON • If you turn off the system or change the source, the AUDIO program is also erased. TV/VIDEO PROGRESSIVE TV CHANNEL To check the program contents DISPLAY STEP STEP...
7 Zoom DVD Special Effect Playback You can zoom in on the picture while playing back a DVD. 7 Still Picture/Frame-by-Frame Playback From the remote control ONLY: You can advance the still picture frame by frame while playing a Press ZOOM to zoom in. DVD.
VCD/CD Playback STANDBY/ON 1/35 00:12 AUDIO TV/VIDEO PROGRESSIVE DISPLAY TV CHANNEL DISPLAY STEP On-screen bar goes off. AUDIO/ SUBTITLE TV VOLUME FM MODE * Appears only when a VCD is loaded. FM/AM CONTROL ** Appears only when a VCD is played back. 1 : Disc type ¢...
Disc Menu–Driven Playback (Only for VCD) Moving to a Particular Portion Directly The Play Back Control function (PBC) allows you to operate the You can move to a particular portion (scene) on the track directly. VCD using menus. • PBC function is canceled when you use this function. When you start playing a VCD with PBC function, a menu will automatically appear on the TV screen.
VCD/CD Playback Note: When the on-screen bar is shown on the screen, Repeat mode indication also changes as follows: STANDBY/ON AUDIO TV/VIDEO PROGRESSIVE REPEAT:ONE REPEAT:DISC TV CHANNEL DISPLAY STEP AUDIO/ SUBTITLE TV VOLUME FM MODE REPEAT OFF FM/AM CONTROL 7 A–B Repeat TUNER PRESET DOWN While playing, you can also select a portion you want to repeat.
Programming the Playing Order of the Repeat steps 3 and 4 to program other tracks Tracks—Program Play you want. • After 10 steps are programed, “NEXT «” is selected (highlighted). If you want to program more steps, press You can arrange the track playback order before you start playing. You can program up to 20 steps.
VCD/CD Playback Selecting Playback Channel When you play back a karaoke VCD or CD, you can only select STANDBY/ON AUDIO either the left channel or right channel to listen to. TV/VIDEO PROGRESSIVE Press AUDIO/FM MODE repeatedly. AUDIO/ STEP FM MODE TV CHANNEL STEP AUDIO/...
7 Zoom VCD Special Effect Playback You can zoom in on the picture while playing a VCD. 7 Still Picture/Frame-by-Frame Playback From the remote control ONLY: You can advance the still picture frame by frame while playing a Press ZOOM to zoom in. VCD.
MP3 Introduction This system is incorporated with an MP3 decoder. You can play back MP3 tracks (files) recorded on CD-Rs and CD-RWs. • Notice that “files” and “tracks” are used interchangeably. STANDBY/ON AUDIO What is MP3? TV/VIDEO PROGRESSIVE MP3 is an abbreviation of Motion Picture Experts Group (or MPEG) DISPLAY Audio Layer 3.
MP3 Playback The on-screen bar Starting Playback It is recommended to turn on your TV when playing back an MP3 disc. 1/35 00:22/03:48 Press 0 to load a disc. 1 : Disc type SVCD Press 3/8. TUNER PRESET After detecting the disc, playback starts. 2 : Current track (file) and total number of the tracks •...
MP3 Playback Operations Using the On-Screen Display STANDBY/ON It is recommended to turn on your TV when playing back an MP3 AUDIO disc. TV/VIDEO PROGRESSIVE When the loaded MP3 disc is recognized, the following on-screen TV CHANNEL STEP DISPLAY display appears on the TV screen. (The contents of this on-screen AUDIO/ SUBTITLE TV VOLUME...
Moving to a Particular Track Directly Repeating Playback You can move to a particular track on the disc directly. On an MP3 disc, A–B Repeat cannot be used. You can enjoy only Repeat play. From the remote control ONLY: SEARCH From the remote control ONLY: Press SEARCH during playback or pause.
Tuner Operations Tuning in Stations From the remote control: STANDBY/ON AUDIO Press FM/AM repeatedly to select the FM/AM band. TV/VIDEO PROGRESSIVE The last received station of the selected band is tuned in. TV CHANNEL DISPLAY STEP AUDIO/ • Each time you press the button, the band alternates FM MODE AUDIO/ FM/AM...
To tune in a preset station Using Preset Tuning From the remote control: Once a station is assigned to a channel number, the station can be Press FM/AM repeatedly to select the FM/AM quickly tuned. You can preset up to 15 FM and 15 AM stations. band.
Setting up the DVD Preferences Setting the Initial Languages You can select your favorite language you listen to or read on the TV STANDBY/ON AUDIO screen. When you operate this system or watch a DVD, you will be able to PROGRESSIVE TV/VIDEO operate the system or to enjoy a DVD in the language you have...
I Basic language selecting procedure Introducing the DVD Preference (System) Ex. : To select the desired language as the initial language for “AUDIO.” You can set the DVD preference to match it to your usage and operating circumstances. From the remote control ONLY: SETUP Press SETUP.
Page 54
Setting up the DVD Preferences Press ∞ (or 5) to select (highlight) one of the system setting items listed on the STANDBY/ON AUDIO menu. ENTER TV/VIDEO PROGRESSIVE SYSTEM LANGUAGES TV CHANNEL DISPLAY STEP TV SCREEN 4 : 3 LB AUDIO/ SUBTITLE TV VOLUME FM MODE...
Press the number buttons to enter the password Setting the Parental (Rating) Level (4 digits). • When shipped from the factory, password is “7890.” Using this function, you can restrict playback of DVD containing • If you enter a wrong password, your setting will be canceled. violent scenes and those not suitable for your family members.
Page 56
Setting up the DVD Preferences LANGUAGES SYSTEM TV SCREEN 4 : 3 LB STANDBY/ON RATING LEVEL LEVEL 4 AUDIO BITSTREAM LEVEL 5 LEVEL 6 LEVEL 7 TV/VIDEO PROGRESSIVE LEVEL 8 NEW PASSWORD TV CHANNEL DISPLAY STEP » « | \ : Move Setup : Exit AUDIO/...
Operating JVC’s Components You can use the remote control to operate not only this unit but also other JVC products. • Refer also to the manuals supplied for the other products. — This remote control can operate a VCR whose remote control code is set to A code.
Operating Other Manufacturers’ TV ❏ To change the transmittable signals for operating a You can use the remote control to operate other manufactures’ TV. 1. Press and hold TV • Refer also to the manuals supplied for the other products. 2.
Maintenance To get the best performance of the unit, keep your discs and mechanism clean. General Notes Cleaning the unit In general, you will have the best performance by keeping your • Stains on the unit discs, and the mechanism clean. Should be wiped off with a soft cloth.
Troubleshooting Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center. PROBLEM POSSIBLE CAUSE SOLUTION Power does not come on. The power cord is not connected correctly.
Specifications Center unit (XV-THA30) Subwoofer (SP-WA30) Amplifier section Speaker: 20 cm Bass-reflex, Magnetically Shielded Front/Center/Rear: 25 watts per channel, min. RMS at 6 ohms as 1 kHz, Power Handling Capacity: 110 W with no more than 10 % total harmonic distortion. 4 Ω...
Page 62
Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada, Australia and U.K.) COMPONENT OUT CAUTION for mains (AC) line BEFORE PLUGGING IN, do check that your mains (AC) line voltage corresponds with the position of the voltage selector switch provided on the outside of this equipment and, if different, reset the voltage selector switch, to prevent from a damage or risk of fire/electric shock.
Page 63
MENU RETURN MUTING STANDBY AUDIO/FM MODE STANDBY/ON VOLUME SOURCE DVD DIGITAL CINEMA SYSTEM TH-A30 D I G I T A L RM-STHA30U DVD CINEMA SYSTEM INSTRUCTIONS MANUAL DE INSTRUCCIONES For Customer Use: Enter below the Model No. and Serial INSTRUÇÕES No.
Page 64
Warnings, Cautions and Others / Avisos, precauciones y otras notas / Advertêcias, precauções e outras notas Caution –– STANDBY/ON switch! Precaução –– Interruptor STANDBY/ON Disconnect the mains plug to shut the power off completely. The Desconectar o cabo de alimentação para desligar a alimentação por STANDBY/ON switch in any position does not disconnect the completo.
Page 65
Caution: Proper Ventilation Precaução: ventilação apropriada To avoid risk of electric shock and fire and to protect from damage. Para prevenir o risco de choque elétrico ou incêndio e para proteger o Locate the apparatus as follows: aparelho contra danos. Front: No obstructions open spacing.
Page 66
IMPORTANT FOR LASER PRODUCTS IMPORTANTE PARA PRODUCTOS LÁSER IMPOTANTE PARA PRODUTOS LASER REPRODUCTION OF LABELS / REPRODUCCIÓN DE ETIQUETAS / REPRODUÇÃO DE ETIQUETAS 1 CLASSIFICATION LABEL, PLACED ON EXTERIOR SURFACE 1 ETIQUETA DE CLASIFICACIÓN, COLOCADA EN LA SUPERFICIE EXTERIOR 1 ETIQUETA DE CLASSIFICACAO, COLOCADA EM SUPERFICIE EXTERNA CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT...
Page 67
1. CLASS 1 LASER PRODUCT 2. CAUTION: Invisible laser radiation when open and inter- lock failed or defeated. Avoid direct exposure to beam. 3. CAUTION: Do not open the top cover. There are no user serviceable parts inside the Unit; leave all servicing to qualified service personnel.
Page 68
7 Dolby Surround ..............20 Setting the Parental (Rating) Level .......... 52 7 DSP (Digital Signal Processor) Modes ........ 21 Operating JVC’s Components ...... 54 Adjusting Stereo Sound ............22 Adjusting Dolby Digital and DTS Digital Surround ....23 Operating Other Manufacturers’ TV .... 55 Activating Dynamic Range Compression ........
Front Panel STANDBY AUDIO/FM MODE STANDBY/ON VOLUME SOURCE DVD DIGITAL CINEMA SYSTEM TH-A30 D I G I T A L See pages in the parentheses for details. Front Panel 1 STANDBY/ON 7 Remote sensor button and STANDBY lamp (11 – 15) 8 3/8 (play/pause) button (11 –...
MUTING IMPORTANT: If you press VCR CONTROL , this remote control will work ONLY for the JVC’s VCR. When you want to operate the system again, press DVD or FM/AM. ; MUTING button (11, 14) a RETURN button (38, 50, 51)
Page 71
Inside the Cover Inside the Cover 1 Number buttons (32, 38, 46, 54, 55) 2 SLOW button (36, 42) TOP MENU MENU RETURN MUTING 3 ZOOM button (36, 42) 4 ANGLE button (30) 5 REPEAT button (33, 39, 46) 6 A–B REPEAT button (33, 39) SOUND 7 CLEAR button (32, 38, 41) 8 SEARCH button (32, 38, 46)
Getting Started Before Installation Putting Batteries in the Remote Control General Precautions Before using the remote control, put two supplied batteries first. • When using the remote control, aim the remote control directly at • DO NOT insert any metal object into the center unit. the remote sensor on the center unit.
Connecting the FM and AM Antennas If AM reception is poor, connect single vinyl-covered wire (not supplied). AM loop antenna (supplied) If FM reception is poor, connect outdoor FM antenna (not supplied). Snap the tabs on the loop into FM antenna (supplied) the slots of the base to assemble the AM loop antenna.
STANDBY AUDIO/FM MODE STANDBY/ON D I G I T A L VOLUME SOURCE S U R R O U N D DVD DIGITAL CINEMA SYSTEM TH-A30 D I G I T A L Subwoofer Right front speaker Left front speaker...
When setting the speakers Connecting the Speakers To obtain the best possible sound from this system, you need to place all the speakers except the subwoofer at the same distance Connect the satellite speakers and subwoofer to the terminals on the from the listening position with each front faced toward the listener.
Getting Started Connecting Audio/Video Component Turn the power off to all components before connections. Audio component connection Illustrations of the input/output terminals below are typical Connect another component to the center unit with the examples. audio cords. When you connect another component, refer also to its Use the cords supplied with another component or purchase manuals since the terminal name actually printed on the rear them at an electric appliance store.
Page 77
TV connection The S-video cord and the component video cord are not supplied with this system. Use the cords supplied with another components or purchase them at an electric appliance store. Component video cord (not supplied) Composite video cord (supplied) Blue S-video cord (not supplied) Green...
(See the manual supplied with your TV.) • The volume level can be adjusted within 51 steps—“MIN (minimum),” • When you use a JVC’s TV, you can turn on your TV by pressing 01 to 49, and “MAX (maximum).”...
Select an Appropriate Progressive Mode To activate DSP modes Press DSP MODE (or DSP on the front panel). DSP MODE You can select the progressive mode according to the picture type The DSP indicator lights up and the current DSP mode (film or video source).
(See the manual supplied with your TV.) • When you use a JVC’s TV, you can turn on your TV by pressing on the remote control, and select the video input by pressing TV/VIDEO. (If your TV is not a JVC’s, see “Operating Other Manufacturers’...
Note: djust the Volume Before activating DSP mode, adjust the speaker setting to bring out the best performance from this system. To increase the volume, press and hold VOLUME +. For in-depth information about adjusting the speaker setting, see To decrease the volume, press and hold VOLUME –. “Speaker Settings”...
Basic Tuner Operations djust the Volume STANDBY/ON AUDIO STANDBY/ON To increase the volume, press and hold VOLUME +. AUDIO To decrease the volume, press and hold VOLUME –. TV/VIDEO PROGRESSIVE VOLUME TV CHANNEL DISPLAY STEP AUDIO/ SUBTITLE TV VOLUME FM MODE CAUTION: FM/AM FM/AM...
Other Basic Operations • When Dolby Surround activates, the PRO LOGIC indicator PROGRESSIVE lights up on the display. TV/VIDEO PROGRESSIVE TV CHANNEL STEP DISPLAY – For in-depth information about Pro Logic modes, see “Creating AUDIO/ SUBTITLE TV VOLUME FM MODE Realistic Sound Fields”...
TV. In such a case, change the scanning mode to “I–SCAN MODE.” • You can change the color system only when the unit is on To check the compatibility of your TV, contact your local JVC standby. customer service center.
Speaker Settings Setting the Delay Time Adjust the delay time of the sounds from the center speaker and the STANDBY/ON rear speakers, comparing to that of the sounds from the front AUDIO speakers. If the distance to the center speaker* and/or the rear speakers** from your listening point is almost the same as from the TV/VIDEO PROGRESSIVE...
Page 86
Speaker Settings For Dolby Pro Logic: Left front Center speaker Right front speaker speaker Before you start, remember... There is a time limit in doing the following steps. If the setting is Subwoofer canceled before you finish, start from step 1 again. 3.0 m Press AUX to select the external 2.7 m...
Creating Realistic Sound Fields You can use the following surround to reproduce a realistic sound Dolby Pro Logic and Dolby 3 Stereo field. Dolby Surround encoding format records the left front channel, • Digital Multichannel Surround—Dolby Digital and DTS Digital right front channel, center channel, and rear channel signals (total 4 Surround channels) into 2 channels.
Page 88
Creating Realistic Sound Fields I DSP (Digital Signal Processor) Modes To check the speaker connections and settings using the test DSP modes have been designed to create important acoustic tone surround elements. 1. Select and play a DVD encoded with Dolby Digital or DTS Digital Surround.
To adjust the output balance for the front speakers 1) Press SOUND repeatedly until the VCR CHANNEL TUNING SOUND adjustment indication for the front B.SEARCH F.SEARCH speakers appears on the display. • Each time you press the button, the adjustment indication ENTER on the display changes as follows: 00 F 00...
Creating Realistic Sound Fields • Each time you press the button, the adjustment indication on the display changes as follows: FM/AM CONTROL 00 F 00 00 R 00 TUNER PRESET DOWN Normal indication REAR VCR CHANNEL TUNING (canceled) B.SEARCH F.SEARCH 00 F (Front) 00 : To adjust the output balance for the front speakers.
To adjust the output balance for the front Activating Dynamic Range Compression speakers and the rear speakers You can enjoy a powerful sound even at a low volume level by 1) Press SOUND repeatedly until one of SOUND compressing the dynamic range (difference between the maximum the following adjustment indications and minimum sounds).
Creating Realistic Sound Fields Adjusting DSP Modes You can adjust the following settings while activating DSP modes. VCR CHANNEL TUNING It is recommended that you make adjustments from your actual B.SEARCH F.SEARCH listening point while listening to reproduced sounds. – Output balance for the front speakers –...
Page 93
To adjust the output level for the rear speakers To adjust the output balance for the front and the subwoofer speakers and the rear speakers 1) Press SOUND repeatedly to select the SOUND 1) Press SOUND repeatedly until one of SOUND the following adjustment indications “REAR”...
Disc Introduction—DVD/VCD/CD This system has been designed to play back the following discs: DVD, IMPORTANT: Video CD, Super Video CD (SVCD), Audio CD, CD-R, and CD-RW. Before performing any operations, make sure of the following..• This system can also play back MP3 files recorded on CD-Rs and •...
Basic Disc Operations To stop playback for a moment TUNER PRESET Press 3/8. While pausing, the elapsed playing time flashes STANDBY/ON AUDIO on the display. • To resume play, press 3/8 again. TV/VIDEO PROGRESSIVE To go to another chapter or track TV CHANNEL DISPLAY STEP...
DVD Playback Showing the On-Screen Bar You can show the following information on the TV screen while a disc is loaded. STANDBY/ON AUDIO From the remote control ONLY: TV/VIDEO PROGRESSIVE DISPLAY Press DISPLAY. DISPLAY TV CHANNEL DISPLAY STEP • Each time you press the button, the following on- SUBTITLE AUDIO/ SUBTITLE...
Selecting the Subtitles Selecting the Multi-Angle Views While playing back a DVD containing subtitles in different While playing back a DVD containing multi-angle views, you can languages, you can select the subtitle to be displayed on the TV view the same scene at different angles. screen.
DVD Playback Disc Menu-Driven Playback Disc menu-driven playback is possible while playing back a DVD STANDBY/ON with menu (menu may be still pictures or moving pictures AUDIO depending on the disc). TV/VIDEO PROGRESSIVE • When operating a disc using the disc menu, refer also to the instructions supplied for the disc.
Moving to a Particular Portion Directly Searching for a Particular Point You can move to another title, chapter, or particular scene in the You can search for a particular point while playing a disc—Variable chapter directly. Speed Forward/Reverse Search. • No sound comes out during Variable Speed Forward/Reverse Search.
DVD Playback 7 A–B Repeat While playing, you can also select a portion you want to repeat. STANDBY/ON AUDIO • A–B repeat is not performed between different titles. • An interval of more than 5 seconds is required between point A TV/VIDEO PROGRESSIVE and point B.
Programming the Playing Order of the Press 3 or 2 to select a chapter number, then Chapters—Program Play ENTER. • 3 : Increases the number. You can arrange the chapter playback order before you start playing. • 2 : Decreases the number. You can program up to 20 steps.
Page 102
DVD Playback To erase the stored program Press 0 to eject the disc. • If you turn off the system or change the source, the STANDBY/ON AUDIO program is also erased. TV/VIDEO PROGRESSIVE To check the program contents TV CHANNEL STEP STEP DISPLAY...
7 Zoom DVD Special Effect Playback You can zoom in on the picture while playing back a DVD. 7 Still Picture/Frame-by-Frame Playback From the remote control ONLY: You can advance the still picture frame by frame while playing a Press ZOOM to zoom in. DVD.
VCD/CD Playback STANDBY/ON 1/35 00:12 AUDIO TV/VIDEO PROGRESSIVE DISPLAY TV CHANNEL DISPLAY STEP On-screen bar goes off. AUDIO/ SUBTITLE TV VOLUME FM MODE * Appears only when a VCD is loaded. FM/AM CONTROL ** Appears only when a VCD is played back. 1 : Disc type ¢...
Disc Menu–Driven Playback (Only for VCD) Moving to a Particular Portion Directly The Play Back Control function (PBC) allows you to operate the You can move to a particular portion (scene) on the track directly. VCD using menus. • PBC function is canceled when you use this function. When you start playing a VCD with PBC function, a menu will automatically appear on the TV screen.
VCD/CD Playback Note: When the on-screen bar is shown on the screen, Repeat mode indication also changes as follows: STANDBY/ON AUDIO TV/VIDEO PROGRESSIVE REPEAT:ONE REPEAT:DISC TV CHANNEL DISPLAY STEP AUDIO/ SUBTITLE TV VOLUME FM MODE REPEAT OFF FM/AM CONTROL 7 A–B Repeat TUNER PRESET DOWN While playing, you can also select a portion you want to repeat.
Programming the Playing Order of the Repeat steps 3 and 4 to program other tracks Tracks—Program Play you want. • After 10 steps are programed, “NEXT «” is selected (highlighted). If you want to program more steps, press You can arrange the track playback order before you start playing. You can program up to 20 steps.
VCD/CD Playback Selecting Playback Channel When you play back a karaoke VCD or CD, you can only select STANDBY/ON AUDIO either the left channel or right channel to listen to. TV/VIDEO PROGRESSIVE Press AUDIO/FM MODE repeatedly. AUDIO/ STEP FM MODE TV CHANNEL STEP AUDIO/...
7 Zoom VCD Special Effect Playback You can zoom in on the picture while playing a VCD. 7 Still Picture/Frame-by-Frame Playback From the remote control ONLY: You can advance the still picture frame by frame while playing a Press ZOOM to zoom in. VCD.
MP3 Introduction This system is incorporated with an MP3 decoder. You can play back MP3 tracks (files) recorded on CD-Rs and CD-RWs. • Notice that “files” and “tracks” are used interchangeably. STANDBY/ON AUDIO What is MP3? TV/VIDEO PROGRESSIVE MP3 is an abbreviation of Motion Picture Experts Group (or MPEG) DISPLAY Audio Layer 3.
MP3 Playback The on-screen bar Starting Playback It is recommended to turn on your TV when playing back an MP3 disc. 1/35 00:22/03:48 Press 0 to load a disc. 1 : Disc type SVCD Press 3/8. TUNER PRESET After detecting the disc, playback starts. 2 : Current track (file) and total number of the tracks •...
MP3 Playback Operations Using the On-Screen Display STANDBY/ON It is recommended to turn on your TV when playing back an MP3 AUDIO disc. TV/VIDEO PROGRESSIVE When the loaded MP3 disc is recognized, the following on-screen TV CHANNEL STEP DISPLAY display appears on the TV screen. (The contents of this on-screen AUDIO/ SUBTITLE TV VOLUME...
Moving to a Particular Track Directly Repeating Playback You can move to a particular track on the disc directly. On an MP3 disc, A–B Repeat cannot be used. You can enjoy only Repeat play. From the remote control ONLY: SEARCH From the remote control ONLY: Press SEARCH during playback or pause.
Tuner Operations Tuning in Stations From the remote control: STANDBY/ON AUDIO Press FM/AM repeatedly to select the FM/AM band. TV/VIDEO PROGRESSIVE The last received station of the selected band is tuned in. TV CHANNEL DISPLAY STEP AUDIO/ • Each time you press the button, the band alternates FM MODE AUDIO/ FM/AM...
To tune in a preset station Using Preset Tuning From the remote control: Once a station is assigned to a channel number, the station can be Press FM/AM repeatedly to select the FM/AM quickly tuned. You can preset up to 15 FM and 15 AM stations. band.
Setting up the DVD Preferences Setting the Initial Languages You can select your favorite language you listen to or read on the TV STANDBY/ON AUDIO screen. When you operate this system or watch a DVD, you will be able to PROGRESSIVE TV/VIDEO operate the system or to enjoy a DVD in the language you have...
I Basic language selecting procedure Introducing the DVD Preference (System) Ex. : To select the desired language as the initial language for “AUDIO.” You can set the DVD preference to match it to your usage and operating circumstances. From the remote control ONLY: SETUP Press SETUP.
Page 118
Setting up the DVD Preferences Press ∞ (or 5) to select (highlight) one of the system setting items listed on the STANDBY/ON AUDIO menu. ENTER TV/VIDEO PROGRESSIVE SYSTEM LANGUAGES TV CHANNEL DISPLAY STEP TV SCREEN 4 : 3 LB AUDIO/ SUBTITLE TV VOLUME FM MODE...
Press the number buttons to enter the password Setting the Parental (Rating) Level (4 digits). • When shipped from the factory, password is “7890.” Using this function, you can restrict playback of DVD containing • If you enter a wrong password, your setting will be canceled. violent scenes and those not suitable for your family members.
Page 120
Setting up the DVD Preferences LANGUAGES SYSTEM TV SCREEN 4 : 3 LB STANDBY/ON RATING LEVEL LEVEL 4 AUDIO BITSTREAM LEVEL 5 LEVEL 6 LEVEL 7 TV/VIDEO PROGRESSIVE LEVEL 8 NEW PASSWORD TV CHANNEL DISPLAY STEP » « | \ : Move Setup : Exit AUDIO/...
Operating JVC’s Components You can use the remote control to operate not only this unit but also other JVC products. • Refer also to the manuals supplied for the other products. — This remote control can operate a VCR whose remote control code is set to A code.
Operating Other Manufacturers’ TV ❏ To change the transmittable signals for operating a You can use the remote control to operate other manufactures’ TV. 1. Press and hold TV • Refer also to the manuals supplied for the other products. 2.
Maintenance To get the best performance of the unit, keep your discs and mechanism clean. General Notes Cleaning the unit In general, you will have the best performance by keeping your • Stains on the unit discs, and the mechanism clean. Should be wiped off with a soft cloth.
Troubleshooting Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center. PROBLEM POSSIBLE CAUSE SOLUTION Power does not come on. The power cord is not connected correctly.
Specifications Center unit (XV-THA30) Subwoofer (SP-WA30) Amplifier section Speaker: 20 cm Bass-reflex, Magnetically Shielded Front/Center/Rear: 25 watts per channel, min. RMS at 6 ohms as 1 kHz, Power Handling Capacity: 110 W with no more than 10 % total harmonic distortion. 4 Ω...
Page 126
Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada, Australia and U.K.) Instrucción sobre la línea de la red (CA) (no aplicable para Europa, EE.UU., Canadá, Australia, ni el Reino Unido) Instrução sobre a tensão da rede eléctrica (CA) (não aplicável para a Europa, os E.U.A., o Canadá, a Austrália e o Reino Unido) COMPONENT OUT CAUTION for mains (AC) line...
Page 127
RETURN MUTING STANDBY AUDIO/FM MODE STANDBY/ON VOLUME SOURCE DVD DIGITAL CINEMA SYSTEM TH-A30 D I G I T A L RM-STHA30U DVD CINEMA SYSTEM INSTRUCTIONS For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet.
Page 128
Warnings, Cautions and Others / Caution –– STANDBY/ON switch! Disconnect the mains plug to shut the power off completely. The STANDBY/ON switch in any position does not disconnect the mains line. The power can be remote controlled. CAUTION To reduce the risk of electrical shocks, fire, etc.: 1.
Page 129
IMPORTANT FOR LASER PRODUCTS / REPRODUCTION OF LABELS / 1 CLASSIFICATION LABEL, PLACED ON EXTERIOR 2 WARNING LABEL, PLACED INSIDE THE UNIT SURFACE CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT PRODUCTO LASER CLASE 1 1.
Page 130
7 Dolby Surround ..............20 Setting the Parental (Rating) Level .......... 52 7 DSP (Digital Signal Processor) Modes ........ 21 Operating JVC’s Components ...... 54 Adjusting Stereo Sound ............22 Adjusting Dolby Digital and DTS Digital Surround ....23 Operating Other Manufacturers’ TV .... 55 Activating Dynamic Range Compression ........
Front Panel STANDBY AUDIO/FM MODE STANDBY/ON VOLUME SOURCE DVD DIGITAL CINEMA SYSTEM TH-A30 D I G I T A L See pages in the parentheses for details. Front Panel 1 STANDBY/ON 7 Remote sensor button and STANDBY lamp (11 – 15) 8 3/8 (play/pause) button (11 –...
MUTING IMPORTANT: If you press VCR CONTROL , this remote control will work ONLY for the JVC’s VCR. When you want to operate the system again, press DVD or FM/AM. ; MUTING button (11, 14) a RETURN button (38, 50, 51)
Page 133
Inside the Cover Inside the Cover 1 Number buttons (32, 38, 46, 54, 55) 2 SLOW button (36, 42) TOP MENU MENU RETURN MUTING 3 ZOOM button (36, 42) 4 ANGLE button (30) 5 REPEAT button (33, 39, 46) 6 A–B REPEAT button (33, 39) SOUND 7 CLEAR button (32, 38, 41) 8 SEARCH button (32, 38, 46)
Getting Started Before Installation Putting Batteries in the Remote Control General Precautions Before using the remote control, put two supplied batteries first. • When using the remote control, aim the remote control directly at • DO NOT insert any metal object into the center unit. the remote sensor on the center unit.
Connecting the FM and AM Antennas If AM reception is poor, connect single vinyl-covered wire (not supplied). AM loop antenna (supplied) If FM reception is poor, connect outdoor FM antenna (not supplied). Snap the tabs on the loop into FM antenna (supplied) the slots of the base to assemble the AM loop antenna.
STANDBY AUDIO/FM MODE STANDBY/ON D I G I T A L VOLUME SOURCE S U R R O U N D DVD DIGITAL CINEMA SYSTEM TH-A30 D I G I T A L Subwoofer Right front speaker Left front speaker...
When setting the speakers Connecting the Speakers To obtain the best possible sound from this system, you need to place all the speakers except the subwoofer at the same distance Connect the satellite speakers and subwoofer to the terminals on the from the listening position with each front faced toward the listener.
Getting Started Connecting Audio/Video Component Turn the power off to all components before connections. Audio component connection Illustrations of the input/output terminals below are typical Connect another component to the center unit with the examples. audio cords. When you connect another component, refer also to its Use the cords supplied with another component or purchase manuals since the terminal name actually printed on the rear them at an electric appliance store.
Page 139
TV connection The S-video cord and the component video cord are not supplied with this system. Use the cords supplied with another components or purchase them at an electric appliance store. Component video cord (not supplied) Composite video cord (supplied) Blue S-video cord (not supplied) Green...
(See the manual supplied with your TV.) • The volume level can be adjusted within 51 steps—“MIN (minimum),” • When you use a JVC’s TV, you can turn on your TV by pressing 01 to 49, and “MAX (maximum).”...
Select an Appropriate Progressive Mode To activate DSP modes Press DSP MODE (or DSP on the front panel). DSP MODE You can select the progressive mode according to the picture type The DSP indicator lights up and the current DSP mode (film or video source).
(See the manual supplied with your TV.) • When you use a JVC’s TV, you can turn on your TV by pressing on the remote control, and select the video input by pressing TV/VIDEO. (If your TV is not a JVC’s, see “Operating Other Manufacturers’...
Note: djust the Volume Before activating DSP mode, adjust the speaker setting to bring out the best performance from this system. To increase the volume, press and hold VOLUME +. For in-depth information about adjusting the speaker setting, see To decrease the volume, press and hold VOLUME –. “Speaker Settings”...
Basic Tuner Operations djust the Volume STANDBY/ON AUDIO STANDBY/ON To increase the volume, press and hold VOLUME +. AUDIO To decrease the volume, press and hold VOLUME –. TV/VIDEO PROGRESSIVE VOLUME TV CHANNEL DISPLAY STEP AUDIO/ SUBTITLE TV VOLUME FM MODE CAUTION: FM/AM FM/AM...
Other Basic Operations • When Dolby Surround activates, the PRO LOGIC indicator PROGRESSIVE lights up on the display. TV/VIDEO PROGRESSIVE TV CHANNEL STEP DISPLAY – For in-depth information about Pro Logic modes, see “Creating AUDIO/ SUBTITLE TV VOLUME FM MODE Realistic Sound Fields”...
TV. In such a case, change the scanning mode to “I–SCAN MODE.” • You can change the color system only when the unit is on To check the compatibility of your TV, contact your local JVC standby. customer service center.
Speaker Settings Setting the Delay Time Adjust the delay time of the sounds from the center speaker and the STANDBY/ON rear speakers, comparing to that of the sounds from the front AUDIO speakers. If the distance to the center speaker* and/or the rear speakers** from your listening point is almost the same as from the TV/VIDEO PROGRESSIVE...
Page 148
Speaker Settings For Dolby Pro Logic: Left front Center speaker Right front speaker speaker Before you start, remember... There is a time limit in doing the following steps. If the setting is Subwoofer canceled before you finish, start from step 1 again. 3.0 m Press AUX to select the external 2.7 m...
Creating Realistic Sound Fields You can use the following surround to reproduce a realistic sound Dolby Pro Logic and Dolby 3 Stereo field. Dolby Surround encoding format records the left front channel, • Digital Multichannel Surround—Dolby Digital and DTS Digital right front channel, center channel, and rear channel signals (total 4 Surround channels) into 2 channels.
Page 150
Creating Realistic Sound Fields I DSP (Digital Signal Processor) Modes To check the speaker connections and settings using the test DSP modes have been designed to create important acoustic tone surround elements. 1. Select and play a DVD encoded with Dolby Digital or DTS Digital Surround.
To adjust the output balance for the front speakers 1) Press SOUND repeatedly until the VCR CHANNEL TUNING SOUND adjustment indication for the front B.SEARCH F.SEARCH speakers appears on the display. • Each time you press the button, the adjustment indication ENTER on the display changes as follows: 00 F 00...
Creating Realistic Sound Fields • Each time you press the button, the adjustment indication on the display changes as follows: FM/AM CONTROL 00 F 00 00 R 00 TUNER PRESET DOWN Normal indication REAR VCR CHANNEL TUNING (canceled) B.SEARCH F.SEARCH 00 F (Front) 00 : To adjust the output balance for the front speakers.
To adjust the output balance for the front Activating Dynamic Range Compression speakers and the rear speakers You can enjoy a powerful sound even at a low volume level by 1) Press SOUND repeatedly until one of SOUND compressing the dynamic range (difference between the maximum the following adjustment indications and minimum sounds).
Creating Realistic Sound Fields Adjusting DSP Modes You can adjust the following settings while activating DSP modes. VCR CHANNEL TUNING It is recommended that you make adjustments from your actual B.SEARCH F.SEARCH listening point while listening to reproduced sounds. – Output balance for the front speakers –...
Page 155
To adjust the output level for the rear speakers To adjust the output balance for the front and the subwoofer speakers and the rear speakers 1) Press SOUND repeatedly to select the SOUND 1) Press SOUND repeatedly until one of SOUND the following adjustment indications “REAR”...
Disc Introduction—DVD/VCD/CD This system has been designed to play back the following discs: DVD, IMPORTANT: Video CD, Super Video CD (SVCD), Audio CD, CD-R, and CD-RW. Before performing any operations, make sure of the following..• This system can also play back MP3 files recorded on CD-Rs and •...
Basic Disc Operations To stop playback for a moment TUNER PRESET Press 3/8. While pausing, the elapsed playing time flashes STANDBY/ON AUDIO on the display. • To resume play, press 3/8 again. TV/VIDEO PROGRESSIVE To go to another chapter or track TV CHANNEL DISPLAY STEP...
DVD Playback Showing the On-Screen Bar You can show the following information on the TV screen while a disc is loaded. STANDBY/ON AUDIO From the remote control ONLY: TV/VIDEO PROGRESSIVE DISPLAY Press DISPLAY. DISPLAY TV CHANNEL DISPLAY STEP • Each time you press the button, the following on- SUBTITLE AUDIO/ SUBTITLE...
Selecting the Subtitles Selecting the Multi-Angle Views While playing back a DVD containing subtitles in different While playing back a DVD containing multi-angle views, you can languages, you can select the subtitle to be displayed on the TV view the same scene at different angles. screen.
DVD Playback Disc Menu-Driven Playback Disc menu-driven playback is possible while playing back a DVD STANDBY/ON with menu (menu may be still pictures or moving pictures AUDIO depending on the disc). TV/VIDEO PROGRESSIVE • When operating a disc using the disc menu, refer also to the instructions supplied for the disc.
Moving to a Particular Portion Directly Searching for a Particular Point You can move to another title, chapter, or particular scene in the You can search for a particular point while playing a disc—Variable chapter directly. Speed Forward/Reverse Search. • No sound comes out during Variable Speed Forward/Reverse Search.
DVD Playback 7 A–B Repeat While playing, you can also select a portion you want to repeat. STANDBY/ON AUDIO • A–B repeat is not performed between different titles. • An interval of more than 5 seconds is required between point A TV/VIDEO PROGRESSIVE and point B.
Programming the Playing Order of the Press 3 or 2 to select a chapter number, then Chapters—Program Play ENTER. • 3 : Increases the number. You can arrange the chapter playback order before you start playing. • 2 : Decreases the number. You can program up to 20 steps.
Page 164
DVD Playback To erase the stored program Press 0 to eject the disc. STANDBY/ON • If you turn off the system or change the source, the AUDIO program is also erased. TV/VIDEO PROGRESSIVE TV CHANNEL To check the program contents DISPLAY STEP STEP...
7 Zoom DVD Special Effect Playback You can zoom in on the picture while playing back a DVD. 7 Still Picture/Frame-by-Frame Playback From the remote control ONLY: You can advance the still picture frame by frame while playing a Press ZOOM to zoom in. DVD.
VCD/CD Playback STANDBY/ON 1/35 00:12 AUDIO TV/VIDEO PROGRESSIVE DISPLAY TV CHANNEL DISPLAY STEP On-screen bar goes off. AUDIO/ SUBTITLE TV VOLUME FM MODE * Appears only when a VCD is loaded. FM/AM CONTROL ** Appears only when a VCD is played back. 1 : Disc type ¢...
Disc Menu–Driven Playback (Only for VCD) Moving to a Particular Portion Directly The Play Back Control function (PBC) allows you to operate the You can move to a particular portion (scene) on the track directly. VCD using menus. • PBC function is canceled when you use this function. When you start playing a VCD with PBC function, a menu will automatically appear on the TV screen.
VCD/CD Playback Note: When the on-screen bar is shown on the screen, Repeat mode indication also changes as follows: STANDBY/ON AUDIO TV/VIDEO PROGRESSIVE REPEAT:ONE REPEAT:DISC TV CHANNEL DISPLAY STEP AUDIO/ SUBTITLE TV VOLUME FM MODE REPEAT OFF FM/AM CONTROL 7 A–B Repeat TUNER PRESET DOWN While playing, you can also select a portion you want to repeat.
Programming the Playing Order of the Repeat steps 3 and 4 to program other tracks Tracks—Program Play you want. • After 10 steps are programed, “NEXT «” is selected (highlighted). If you want to program more steps, press You can arrange the track playback order before you start playing. You can program up to 20 steps.
VCD/CD Playback Selecting Playback Channel When you play back a karaoke VCD or CD, you can only select STANDBY/ON AUDIO either the left channel or right channel to listen to. TV/VIDEO PROGRESSIVE Press AUDIO/FM MODE repeatedly. AUDIO/ STEP FM MODE TV CHANNEL STEP AUDIO/...
7 Zoom VCD Special Effect Playback You can zoom in on the picture while playing a VCD. 7 Still Picture/Frame-by-Frame Playback From the remote control ONLY: You can advance the still picture frame by frame while playing a Press ZOOM to zoom in. VCD.
MP3 Introduction This system is incorporated with an MP3 decoder. You can play back MP3 tracks (files) recorded on CD-Rs and CD-RWs. • Notice that “files” and “tracks” are used interchangeably. STANDBY/ON AUDIO What is MP3? TV/VIDEO PROGRESSIVE MP3 is an abbreviation of Motion Picture Experts Group (or MPEG) DISPLAY Audio Layer 3.
MP3 Playback The on-screen bar Starting Playback It is recommended to turn on your TV when playing back an MP3 disc. 1/35 00:22/03:48 Press 0 to load a disc. 1 : Disc type SVCD Press 3/8. TUNER PRESET After detecting the disc, playback starts. 2 : Current track (file) and total number of the tracks •...
MP3 Playback Operations Using the On-Screen Display STANDBY/ON It is recommended to turn on your TV when playing back an MP3 AUDIO disc. TV/VIDEO PROGRESSIVE When the loaded MP3 disc is recognized, the following on-screen TV CHANNEL STEP DISPLAY display appears on the TV screen. (The contents of this on-screen AUDIO/ SUBTITLE TV VOLUME...
Moving to a Particular Track Directly Repeating Playback You can move to a particular track on the disc directly. On an MP3 disc, A–B Repeat cannot be used. You can enjoy only Repeat play. From the remote control ONLY: SEARCH From the remote control ONLY: Press SEARCH during playback or pause.
Tuner Operations Tuning in Stations From the remote control: STANDBY/ON AUDIO Press FM/AM repeatedly to select the FM/AM band. TV/VIDEO PROGRESSIVE The last received station of the selected band is tuned in. TV CHANNEL DISPLAY STEP AUDIO/ • Each time you press the button, the band alternates FM MODE AUDIO/ FM/AM...
To tune in a preset station Using Preset Tuning From the remote control: Once a station is assigned to a channel number, the station can be Press FM/AM repeatedly to select the FM/AM quickly tuned. You can preset up to 15 FM and 15 AM stations. band.
Setting up the DVD Preferences Setting the Initial Languages You can select your favorite language you listen to or read on the TV STANDBY/ON AUDIO screen. When you operate this system or watch a DVD, you will be able to PROGRESSIVE TV/VIDEO operate the system or to enjoy a DVD in the language you have...
I Basic language selecting procedure Introducing the DVD Preference (System) Ex. : To select the desired language as the initial language for “AUDIO.” You can set the DVD preference to match it to your usage and operating circumstances. From the remote control ONLY: SETUP Press SETUP.
Page 180
Setting up the DVD Preferences Press ∞ (or 5) to select (highlight) one of the system setting items listed on the STANDBY/ON AUDIO menu. ENTER TV/VIDEO PROGRESSIVE SYSTEM LANGUAGES TV CHANNEL DISPLAY STEP TV SCREEN 4 : 3 LB AUDIO/ SUBTITLE TV VOLUME FM MODE...
Press the number buttons to enter the password Setting the Parental (Rating) Level (4 digits). • When shipped from the factory, password is “7890.” Using this function, you can restrict playback of DVD containing • If you enter a wrong password, your setting will be canceled. violent scenes and those not suitable for your family members.
Page 182
Setting up the DVD Preferences LANGUAGES SYSTEM TV SCREEN 4 : 3 LB STANDBY/ON RATING LEVEL LEVEL 4 AUDIO BITSTREAM LEVEL 5 LEVEL 6 LEVEL 7 TV/VIDEO PROGRESSIVE LEVEL 8 NEW PASSWORD TV CHANNEL DISPLAY STEP » « | \ : Move Setup : Exit AUDIO/...
Operating JVC’s Components You can use the remote control to operate not only this unit but also other JVC products. • Refer also to the manuals supplied for the other products. — This remote control can operate a VCR whose remote control code is set to A code.
Operating Other Manufacturers’ TV ❏ To change the transmittable signals for operating a You can use the remote control to operate other manufactures’ TV. 1. Press and hold TV • Refer also to the manuals supplied for the other products. 2.
Maintenance To get the best performance of the unit, keep your discs and mechanism clean. General Notes Cleaning the unit In general, you will have the best performance by keeping your • Stains on the unit discs, and the mechanism clean. Should be wiped off with a soft cloth.
Troubleshooting Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center. PROBLEM POSSIBLE CAUSE SOLUTION Power does not come on. The power cord is not connected correctly.
Specifications Center unit (XV-THA30) Subwoofer (SP-WA30) Amplifier section Speaker: 20 cm Bass-reflex, Magnetically Shielded Front/Center/Rear: 25 watts per channel, min. RMS at 6 ohms as 1 kHz, Power Handling Capacity: 110 W with no more than 10 % total harmonic distortion. 4 Ω...
Page 188
Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada, Australia and U.K.) COMPONENT OUT CAUTION for mains (AC) line BEFORE PLUGGING IN, do check that your mains (AC) line voltage corresponds with the position of the voltage selector switch provided on the outside of this equipment and, if different, reset the voltage selector switch, to prevent from a damage or risk of fire/electric shock.
Page 189
RETURN MUTING STANDBY AUDIO/FM MODE STANDBY/ON VOLUME SOURCE DVD DIGITAL CINEMA SYSTEM TH-A30 D I G I T A L RM-STHA30U DVD CINEMA SYSTEM INSTRUCTIONS For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet.
Page 190
Warnings, Cautions and Others Caution –– STANDBY/ON switch! Disconnect the mains plug to shut the power off completely. The STANDBY/ON switch in any position does not disconnect the mains line. The power can be remote controlled. CAUTION To reduce the risk of electrical shocks, fire, etc.: 1.
Page 191
IMPORTANT FOR LASER PRODUCTS REPRODUCTION OF LABELS 1 CLASSIFICATION LABEL, PLACED ON EXTERIOR 2 WARNING LABEL, PLACED INSIDE THE UNIT SURFACE CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT PRODUCTO LASER CLASE 1 1.
Page 192
7 Dolby Surround ..............20 Setting the Parental (Rating) Level .......... 52 7 DSP (Digital Signal Processor) Modes ........ 21 Operating JVC’s Components ...... 54 Adjusting Stereo Sound ............22 Adjusting Dolby Digital and DTS Digital Surround ....23 Operating Other Manufacturers’ TV .... 55 Activating Dynamic Range Compression ........
Front Panel STANDBY AUDIO/FM MODE STANDBY/ON VOLUME SOURCE DVD DIGITAL CINEMA SYSTEM TH-A30 D I G I T A L See pages in the parentheses for details. Front Panel 1 STANDBY/ON 7 Remote sensor button and STANDBY lamp (11 – 15) 8 3/8 (play/pause) button (11 –...
MUTING IMPORTANT: If you press VCR CONTROL , this remote control will work ONLY for the JVC’s VCR. When you want to operate the system again, press DVD or FM/AM. ; MUTING button (11, 14) a RETURN button (38, 50, 51)
Page 195
Inside the Cover Inside the Cover 1 Number buttons (32, 38, 46, 54, 55) 2 SLOW button (36, 42) TOP MENU MENU RETURN MUTING 3 ZOOM button (36, 42) 4 ANGLE button (30) 5 REPEAT button (33, 39, 46) 6 A–B REPEAT button (33, 39) SOUND 7 CLEAR button (32, 38, 41) 8 SEARCH button (32, 38, 46)
Getting Started Before Installation Putting Batteries in the Remote Control General Precautions Before using the remote control, put two supplied batteries first. • When using the remote control, aim the remote control directly at • DO NOT insert any metal object into the center unit. the remote sensor on the center unit.
Connecting the FM and AM Antennas If AM reception is poor, connect single vinyl-covered wire (not supplied). AM loop antenna (supplied) If FM reception is poor, connect outdoor FM antenna (not supplied). Snap the tabs on the loop into FM antenna (supplied) the slots of the base to assemble the AM loop antenna.
STANDBY AUDIO/FM MODE STANDBY/ON D I G I T A L VOLUME SOURCE S U R R O U N D DVD DIGITAL CINEMA SYSTEM TH-A30 D I G I T A L Subwoofer Right front speaker Left front speaker...
When setting the speakers Connecting the Speakers To obtain the best possible sound from this system, you need to place all the speakers except the subwoofer at the same distance Connect the satellite speakers and subwoofer to the terminals on the from the listening position with each front faced toward the listener.
Getting Started Connecting Audio/Video Component Turn the power off to all components before connections. Audio component connection Illustrations of the input/output terminals below are typical Connect another component to the center unit with the examples. audio cords. When you connect another component, refer also to its Use the cords supplied with another component or purchase manuals since the terminal name actually printed on the rear them at an electric appliance store.
Page 201
TV connection The S-video cord and the component video cord are not supplied with this system. Use the cords supplied with another components or purchase them at an electric appliance store. Component video cord (not supplied) Composite video cord (supplied) Blue S-video cord (not supplied) Green...
(See the manual supplied with your TV.) • The volume level can be adjusted within 51 steps—“MIN (minimum),” • When you use a JVC’s TV, you can turn on your TV by pressing 01 to 49, and “MAX (maximum).”...
Select an Appropriate Progressive Mode To activate DSP modes Press DSP MODE (or DSP on the front panel). DSP MODE You can select the progressive mode according to the picture type The DSP indicator lights up and the current DSP mode (film or video source).
(See the manual supplied with your TV.) • When you use a JVC’s TV, you can turn on your TV by pressing on the remote control, and select the video input by pressing TV/VIDEO. (If your TV is not a JVC’s, see “Operating Other Manufacturers’...
Note: djust the Volume Before activating DSP mode, adjust the speaker setting to bring out the best performance from this system. To increase the volume, press and hold VOLUME +. For in-depth information about adjusting the speaker setting, see To decrease the volume, press and hold VOLUME –. “Speaker Settings”...
Basic Tuner Operations djust the Volume STANDBY/ON AUDIO STANDBY/ON To increase the volume, press and hold VOLUME +. AUDIO To decrease the volume, press and hold VOLUME –. TV/VIDEO PROGRESSIVE VOLUME TV CHANNEL DISPLAY STEP AUDIO/ SUBTITLE TV VOLUME FM MODE CAUTION: FM/AM FM/AM...
Other Basic Operations • When Dolby Surround activates, the PRO LOGIC indicator PROGRESSIVE lights up on the display. TV/VIDEO PROGRESSIVE TV CHANNEL STEP DISPLAY – For in-depth information about Pro Logic modes, see “Creating AUDIO/ SUBTITLE TV VOLUME FM MODE Realistic Sound Fields”...
TV. In such a case, change the scanning mode to “I–SCAN MODE.” • You can change the color system only when the unit is on To check the compatibility of your TV, contact your local JVC standby. customer service center.
Speaker Settings Setting the Delay Time Adjust the delay time of the sounds from the center speaker and the STANDBY/ON rear speakers, comparing to that of the sounds from the front AUDIO speakers. If the distance to the center speaker* and/or the rear speakers** from your listening point is almost the same as from the TV/VIDEO PROGRESSIVE...
Page 210
Speaker Settings For Dolby Pro Logic: Left front Center speaker Right front speaker speaker Before you start, remember... There is a time limit in doing the following steps. If the setting is Subwoofer canceled before you finish, start from step 1 again. 3.0 m Press AUX to select the external 2.7 m...
Creating Realistic Sound Fields You can use the following surround to reproduce a realistic sound Dolby Pro Logic and Dolby 3 Stereo field. Dolby Surround encoding format records the left front channel, • Digital Multichannel Surround—Dolby Digital and DTS Digital right front channel, center channel, and rear channel signals (total 4 Surround channels) into 2 channels.
Page 212
Creating Realistic Sound Fields I DSP (Digital Signal Processor) Modes To check the speaker connections and settings using the test DSP modes have been designed to create important acoustic tone surround elements. 1. Select and play a DVD encoded with Dolby Digital or DTS Digital Surround.
To adjust the output balance for the front speakers VCR CHANNEL 1) Press SOUND repeatedly until the TUNING SOUND adjustment indication for the front B.SEARCH F.SEARCH speakers appears on the display. • Each time you press the button, the adjustment indication ENTER on the display changes as follows: 00 F 00...
Creating Realistic Sound Fields • Each time you press the button, the adjustment indication on the display changes as follows: FM/AM CONTROL 00 F 00 00 R 00 TUNER PRESET DOWN Normal indication REAR VCR CHANNEL TUNING (canceled) B.SEARCH F.SEARCH 00 F (Front) 00 : To adjust the output balance for the front speakers.
To adjust the output balance for the front Activating Dynamic Range Compression speakers and the rear speakers You can enjoy a powerful sound even at a low volume level by 1) Press SOUND repeatedly until one of SOUND compressing the dynamic range (difference between the maximum the following adjustment indications and minimum sounds).
Creating Realistic Sound Fields Adjusting DSP Modes You can adjust the following settings while activating DSP modes. VCR CHANNEL TUNING It is recommended that you make adjustments from your actual B.SEARCH F.SEARCH listening point while listening to reproduced sounds. – Output balance for the front speakers –...
Page 217
To adjust the output level for the rear speakers To adjust the output balance for the front and the subwoofer speakers and the rear speakers 1) Press SOUND repeatedly to select the SOUND 1) Press SOUND repeatedly until one of SOUND “REAR”...
Disc Introduction—DVD/VCD/CD This system has been designed to play back the following discs: DVD, IMPORTANT: Video CD, Super Video CD (SVCD), Audio CD, CD-R, and CD-RW. Before performing any operations, make sure of the following..• This system can also play back MP3 files recorded on CD-Rs and •...
Basic Disc Operations To stop playback for a moment TUNER PRESET Press 3/8. While pausing, the elapsed playing time flashes STANDBY/ON AUDIO on the display. • To resume play, press 3/8 again. TV/VIDEO PROGRESSIVE To go to another chapter or track TV CHANNEL DISPLAY STEP...
DVD Playback Showing the On-Screen Bar You can show the following information on the TV screen while a disc is loaded. STANDBY/ON AUDIO From the remote control ONLY: TV/VIDEO PROGRESSIVE DISPLAY Press DISPLAY. DISPLAY TV CHANNEL DISPLAY STEP • Each time you press the button, the following on- SUBTITLE AUDIO/ SUBTITLE...
Selecting the Subtitles Selecting the Multi-Angle Views While playing back a DVD containing subtitles in different While playing back a DVD containing multi-angle views, you can languages, you can select the subtitle to be displayed on the TV view the same scene at different angles. screen.
DVD Playback Disc Menu-Driven Playback Disc menu-driven playback is possible while playing back a DVD STANDBY/ON with menu (menu may be still pictures or moving pictures AUDIO depending on the disc). TV/VIDEO PROGRESSIVE • When operating a disc using the disc menu, refer also to the instructions supplied for the disc.
Moving to a Particular Portion Directly Searching for a Particular Point You can move to another title, chapter, or particular scene in the You can search for a particular point while playing a disc—Variable chapter directly. Speed Forward/Reverse Search. • No sound comes out during Variable Speed Forward/Reverse Search.
DVD Playback 7 A–B Repeat While playing, you can also select a portion you want to repeat. STANDBY/ON AUDIO • A–B repeat is not performed between different titles. • An interval of more than 5 seconds is required between point A TV/VIDEO PROGRESSIVE and point B.
Programming the Playing Order of the Press 3 or 2 to select a chapter number, then Chapters—Program Play ENTER. • 3 : Increases the number. You can arrange the chapter playback order before you start playing. • 2 : Decreases the number. You can program up to 20 steps.
Page 226
DVD Playback To erase the stored program Press 0 to eject the disc. • If you turn off the system or change the source, the STANDBY/ON AUDIO program is also erased. TV/VIDEO PROGRESSIVE To check the program contents STEP TV CHANNEL DISPLAY STEP You can check the program contents by pressing PROGRAM.
7 Zoom DVD Special Effect Playback You can zoom in on the picture while playing back a DVD. 7 Still Picture/Frame-by-Frame Playback From the remote control ONLY: You can advance the still picture frame by frame while playing a Press ZOOM to zoom in. DVD.
VCD/CD Playback STANDBY/ON 1/35 00:12 AUDIO TV/VIDEO PROGRESSIVE DISPLAY TV CHANNEL DISPLAY STEP On-screen bar goes off. AUDIO/ SUBTITLE TV VOLUME FM MODE * Appears only when a VCD is loaded. FM/AM CONTROL ** Appears only when a VCD is played back. 1 : Disc type ¢...
Disc Menu–Driven Playback (Only for VCD) Moving to a Particular Portion Directly The Play Back Control function (PBC) allows you to operate the You can move to a particular portion (scene) on the track directly. VCD using menus. • PBC function is canceled when you use this function. When you start playing a VCD with PBC function, a menu will automatically appear on the TV screen.
VCD/CD Playback Note: When the on-screen bar is shown on the screen, Repeat mode indication also changes as follows: STANDBY/ON AUDIO TV/VIDEO PROGRESSIVE REPEAT:ONE REPEAT:DISC TV CHANNEL DISPLAY STEP AUDIO/ SUBTITLE TV VOLUME FM MODE REPEAT OFF FM/AM CONTROL 7 A–B Repeat TUNER PRESET DOWN While playing, you can also select a portion you want to repeat.
Programming the Playing Order of the Repeat steps 3 and 4 to program other tracks Tracks—Program Play you want. • After 10 steps are programed, “NEXT «” is selected (highlighted). If you want to program more steps, press You can arrange the track playback order before you start playing. You can program up to 20 steps.
VCD/CD Playback Selecting Playback Channel When you play back a karaoke VCD or CD, you can only select STANDBY/ON AUDIO either the left channel or right channel to listen to. TV/VIDEO PROGRESSIVE Press AUDIO/FM MODE repeatedly. AUDIO/ STEP FM MODE TV CHANNEL STEP AUDIO/...
7 Zoom VCD Special Effect Playback You can zoom in on the picture while playing a VCD. 7 Still Picture/Frame-by-Frame Playback From the remote control ONLY: You can advance the still picture frame by frame while playing a Press ZOOM to zoom in. VCD.
MP3 Introduction This system is incorporated with an MP3 decoder. You can play back MP3 tracks (files) recorded on CD-Rs and CD-RWs. • Notice that “files” and “tracks” are used interchangeably. STANDBY/ON AUDIO What is MP3? TV/VIDEO PROGRESSIVE MP3 is an abbreviation of Motion Picture Experts Group (or MPEG) DISPLAY Audio Layer 3.
MP3 Playback The on-screen bar Starting Playback It is recommended to turn on your TV when playing back an MP3 disc. 1/35 00:22/03:48 Press 0 to load a disc. 1 : Disc type SVCD Press 3/8. TUNER PRESET After detecting the disc, playback starts. 2 : Current track (file) and total number of the tracks •...
MP3 Playback Operations Using the On-Screen Display STANDBY/ON It is recommended to turn on your TV when playing back an MP3 AUDIO disc. TV/VIDEO PROGRESSIVE When the loaded MP3 disc is recognized, the following on-screen TV CHANNEL STEP DISPLAY display appears on the TV screen. (The contents of this on-screen AUDIO/ SUBTITLE TV VOLUME...
Moving to a Particular Track Directly Repeating Playback You can move to a particular track on the disc directly. On an MP3 disc, A–B Repeat cannot be used. You can enjoy only Repeat play. From the remote control ONLY: SEARCH From the remote control ONLY: Press SEARCH during playback or pause.
Tuner Operations On the front panel: Press SOURCE repeatedly until the SOURCE desired band appears on the display. STANDBY/ON AUDIO The last received station of the selected band is tuned TV/VIDEO PROGRESSIVE • Each time you press the button, the source changes as follows: TV CHANNEL DISPLAY STEP...
To tune in a preset station Using Preset Tuning From the remote control: Once a station is assigned to a channel number, the station can be Press FM/AM repeatedly to select the FM/AM quickly tuned. You can preset up to 15 FM and 15 AM stations. band.
Setting up the DVD Preferences Setting the Initial Languages You can select your favorite language you listen to or read on the TV STANDBY/ON AUDIO screen. When you operate this system or watch a DVD, you will be able to PROGRESSIVE TV/VIDEO operate the system or to enjoy a DVD in the language you have...
I Basic language selecting procedure Introducing the DVD Preference (System) Ex. : To select the desired language as the initial language for “AUDIO.” You can set the DVD preference to match it to your usage and operating circumstances. From the remote control ONLY: SETUP Press SETUP.
Page 242
Setting up the DVD Preferences Press ∞ (or 5) to select (highlight) one of the system setting items listed on the STANDBY/ON AUDIO menu. ENTER TV/VIDEO PROGRESSIVE SYSTEM LANGUAGES TV CHANNEL DISPLAY STEP TV SCREEN 4 : 3 LB AUDIO/ SUBTITLE TV VOLUME FM MODE...
Press the number buttons to enter the password Setting the Parental (Rating) Level (4 digits). • When shipped from the factory, password is “7890.” Using this function, you can restrict playback of DVD containing • If you enter a wrong password, your setting will be canceled. violent scenes and those not suitable for your family members.
Page 244
Setting up the DVD Preferences SYSTEM LANGUAGES TV SCREEN 4 : 3 LB STANDBY/ON RATING LEVEL LEVEL 4 AUDIO LEVEL 5 BITSTREAM LEVEL 6 LEVEL 7 TV/VIDEO PROGRESSIVE LEVEL 8 TV CHANNEL NEW PASSWORD DISPLAY STEP » « | \ : Move Setup : Exit AUDIO/...
Operating JVC’s Components You can use the remote control to operate not only this unit but also other JVC products. • Refer also to the manuals supplied for the other products. — This remote control can operate a VCR whose remote control code is set to A code.
Operating Other Manufacturers’ TV ❏ To change the transmittable signals for operating a You can use the remote control to operate other manufactures’ TV. 1. Press and hold TV • Refer also to the manuals supplied for the other products. 2.
Maintenance To get the best performance of the unit, keep your discs and mechanism clean. General Notes Cleaning the unit In general, you will have the best performance by keeping your • Stains on the unit discs, and the mechanism clean. Should be wiped off with a soft cloth.
Troubleshooting Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center. PROBLEM SOLUTION POSSIBLE CAUSE Power does not come on. Insert the plug into the socket. The power cord is not connected correctly.
Specifications Center unit (XV-THA30) Subwoofer (SP-WA30) Amplifier section Speaker: 20 cm Bass-reflex, Magnetically Shielded Front/Center/Rear: 25 watts per channel, min. RMS at 6 ohms as 1 kHz, Power Handling Capacity: 110 W with no more than 10 % total harmonic distortion. 4 Ω...