Hitachi SJ700 Series Manual page 20

Variable frequency drive

Hide thumbs Also See for SJ700 Series:

Instruction manual (46 pages)

Manual (41 pages)

Software manual (15 pages)

Table Of Contents

Table of Contents

●C GROUP: INTELLIGENT TERMINAL FUNCTIONS

Code

Function Name

C030

Digital current monitor reference value

C031

Terminal (11) active state

C032

Terminal (12) active state

C033

Terminal (13) active state

C034

Terminal (14) active state

C035

Terminal (15) active state

C036

Alarm relay terminal active state

C038

Low-current indication signal output mode selection

C039

Low-current indication signal detection level

C040

Overload signal output mode

C041

Overload level setting

C042

Frequency arrival setting for accel.

C043

Frequency arrival setting for decel.

C044

PID deviation level setting

C045

Frequency arrival setting for acceleration (2)

C046

Frequency arrival setting for deceleration (2)

C052

Maximum PID feedback data

C053

Minimum PID feedback data

C055

Over-torque(Forward-driving) level setting

C056

Over-torque(Reverse-regenerating) level setting

C057

Over-torque(Reverse-driving) level setting

C058

Over-torque(Forward-regenerating) level setting

C061

Electronic thermal warning level setting

C062

Alarm code input

C063

Zero speed detection level

C064

Heat sink overheat warning level

C071

Communication speed selection

C072

Node allocation

C073

Communication data length selection

C074

Communication parity selection

C075

Communication stop bit selection

C076

Selection of the operation after communication error

C077

Communication timeout limit before tripping

C078

Communication wait time

C079

Communication mode selection

C081

O input span calibration

C082

OI input span calibration

C083

O2 input span calibration

C085

Thermistor input tuning

C091

Debug mode enable

C101

UP/DOWN memory mode selection

C102

Reset mode selection

C103

Restart mode after reset

C105

FM gain adjustment

C106

AM gain adjustment

C107

AMI gain adjustment

C109

AM bias adjustment

C110

AMI bias adjustment

C111

Overload setting (2)

C121

O input zero calibration

C122

OI input zero calibration

C123

O2 input zero calibration

C130

Output 11 on-delay time

C131

Output 11 off-delay time

C132

Output 12 on-delay time

C133

Output 12 off-delay time

C134

Output 13 on-delay time

C135

Output 13 off-delay time

C136

Output 14 on-delay time

C137

Output 14 off-delay time

C138

Output 15 on-delay time

C139

Output 15 off-delay time

C140

Output RY on-delay time

C141

Output RY off-delay time

C142

Logical output signal 1 selection 1

C143

Logical output signal 1 selection 2

C144

Logical output signal 1 operator selection

C145

Logical output signal 2 selection 1

C146

Logical output signal 2 selection 2

(*1)4000HF:0.00 to 99.99 , 100.0 to 120.0(Hz)

Monitored data or setting

SJ700:0.20 x "rated current" to 2.00 x "rated current" (A) / L700:0.20 x "rated current" to 1.50 x "rated current" (A)

(Current with digital current monitor output at 1,440 Hz)

00(NO) / 01(NC)

00 (output during acceleration/deceleration and constant-speed operation),

01 (output only during constant-speed operation)

SJ700:0.0 to 2.00 x "rated current" (A) / L700:0.0 to 1.50 x "rated current" (A)

00 (output during acceleration/deceleration and constant-speed operation),

01 (output only during constant-speed operation)

SJ700:0.0 to 2.00 x "rated current" (A) / L700:0.0 to 1.50 x "rated current" (A)

0.00 to 99.99, 100.0 to 400.0 (Hz) (*1)

0.0 to 100.0 (%)

0.00 to 99.99, 100.0 to 400.0 (Hz) (*1)

0.0 to 100.0 (%)

SJ700: 0. to 200. (%) < 75kW and over:0. to 180.>

L700: 0. to 150. (%)

SJ700: 0. to 200. (%) < 75kW and over:0. to 180.>

L700: 0. to 150. (%)

SJ700: 0. to 200. (%) < 75kW and over:0. to 180.>

L700: 0. to 150. (%)

SJ700: 0. to 200. (%) < 75kW and over:0. to 180.>

L700: 0. to 150. (%)

0. to 100. (%)

00(Disabled) / 01(3-bit) / 02(4-bit)

0.00 to 99.99, 100.0 (Hz)

0. to 200.0 (℃)

02 (loopback test), 03 (2,400 bps), 04 (4,800 bps), 05 (9,600 bps), 06 (19,200 bps)

1. to 32.

7 (7 bits), 8 (8 bits)

00 (no parity), 01 (even parity), 02 (odd parity)

1 (1 bit), 2 (2 bits)

00 (tripping), 01 (tripping after decelerating and stopping the motor), 02 (ignoring errors),

03 (stopping the motor after free-running), 04 (decelerating and stopping the motor)

0.00 to 99.99 (s)

0. to 1000. (ms)

00(ASCII), 01(Modbus-RTU)

0. to 9999., 1000 to 6553(10000 to 65530)

0. to 9999., 1000 to 6553(10000～65530)

0.0 to 999.9, 1000.

(Do not change this parameter, which is intended for factory adjustment.)

00 (not storing the frequency data), 01 (storing the frequency data)

00 (resetting the trip when RS is on), 01 (resetting the trip when RS is off),

02 (enabling resetting only upon tripping [resetting when RS is on])

00 (starting with 0 Hz), 01 (starting with matching frequency),

02 (restarting with active matching frequency)

50. to 200. (%)

0. to 100. (%)

SJ700:0.0 to 2.00 x "rated current" (A) <75kW and over:0.0 to 1.80 x "rated current">

L700:0.0 to 1.50 x "rated current" (A)

0. to 9999., 1000 to 6553 (10000 to 65530)

0.0 to 100.0 (s)

Same as the settings of C021 to C026 (except those of LOG1 to LOG6)

00 (AND), 01 (OR), 02 (XOR)

Same as the settings of C021 to C026 (except those of LOG1 to LOG6)

［◯= Allowed

= Not permitted］

Default Setting

Setting

SJ700

during operation

L700

(allowed or not)

-FE(CE) -FU(UL)

-F(JP)

Rated current of

○

inverterx 1..0

Rated current of inverterx 1..0

0.00

3.0

0.00

100.0

0.0

100.

80.

0.00

120.

0.00

Factory set

○

100.

○

100.

○

100.

○

20.

○

Rated current of

inverterx 1..0

○

Factory set

○

0.0

○

0.0

Change

during operation

(allowed or not)

○

Table of Contents

This manual is also suitable for:

L700 series

Hitachi SJ700 Series Manual page 20

Related Manuals for Hitachi SJ700 Series

Related Products for Hitachi SJ700 Series

This manual is also suitable for:

Table of Contents