Mitsubishi Electric Jet Towel JT-S1AP-W-NA Installation Manual
Hide thumbs
Also See for Jet Towel JT-S1AP-W-NA:
- Instruction manual (9 pages) ,
- Installation manual (14 pages) ,
- Handbook (37 pages)
Table of Contents
Advertisement
Quick Links
MODEL
JT-S1AP-W-NA
JT-S1AP-S-NA
Unit colour -W
(White)
INSTALLATION MANUAL
Read the manual thoroughly before beginning installation to ensure the unit is installed safely and correctly.
Installation shall comply with local requirements and Electrical Code and be performed by the dealer or a qualifi ed
professional in accordance to local jurisdiction.
The "INSTRUCTION MANUAL" is for the customer. Be sure to hand it to the customer.
INDEX
Hand dryer
Heater Model
-S
( Silver )
6 - 12
Location of Name plate indicating
Model name and Electrical ratings
For Dealers and Installers
2
3
3
3
4
5
5
5
5
12
12
13
13
− NA - 1 −
－ 1 －
Input Power: 120 Vac Single-phase
Indoor use only
876HE3901
Advertisement
Table of Contents
Related Manuals for Mitsubishi Electric Jet Towel JT-S1AP-W-NA
Summary of Contents for Mitsubishi Electric Jet Towel JT-S1AP-W-NA
-
Page 1: Table Of Contents
876HE3901 Hand dryer MODEL JT-S1AP-W-NA Location of Name plate indicating Heater Model Model name and Electrical ratings JT-S1AP-S-NA Input Power: 120 Vac Single-phase Unit colour -W (White) ( Silver ) Indoor use only For Dealers and Installers INSTALLATION MANUAL Read the manual thoroughly before beginning installation to ensure the unit is installed safely and correctly. Installation shall comply with local requirements and Electrical Code and be performed by the dealer or a qualifi... -
Page 2: Safety Precautions
Safety Precautions ● The dangers arising from improper handling and the extents of the dangers are classified and explained as shown below. Warning The following may lead to death or serious personal injury if handled incorrectly. ● Do not install in locations where they ●... -
Page 3: Pre-Installation Checks
Pre-installation checks Warning ● Input Power: 120 Vac Single-phase is used. Using the incorrect power supply may cause fi res, electric shocks or malfunctions. ■ Checking the installation environment Do not install the unit in the following types of locations. ... -
Page 4: Names Of Parts And External Dimensions
Names of parts and external dimensions ■ Main unit TERMINAL BLOCK " (63) " (160.5) " (3) " (250) " (100) " HOLE FOR (140) Unit (in. (mm)) POWER CORD (REAR) NOTE ● Confi rm the details in the "Installation conditions" (Page 5). ■... -
Page 5: Installation Conditions
Installation conditions ■ Required space for installation Top side Be sure to secure at least the Unit (in. (mm)) Caution distances listed in the right- Isolation Location hand table from walls, fl ammable distance (combustible) materials and so Above " (150) Left Left "... -
Page 6: Installation Method
Installation method For confi rmation □ Input Power: 120 Vac Single-phase power is being used (using the incorrect power supply may cause fi res, electric shocks or malfunctions). □ The ground fault circuit interrupter is attached (not attaching a ground fault circuit interrupter may result in electric shocks). - Page 7 Installation method - continuation ■ Fixing the installation panel Fix the installation panel onto the wall with 4 accessory mounting screws Installation panel (5×30). ● The "Installation position guide" illustrated on the right is recommended. ● When installing on a wall, select a wall with a fl...
- Page 8 Installation method - continuation NOTE Front cover Prevent scratching on the front cover. Rust ● may form on the scratched area. 1. Remove the tape Ⓐ , then remove the Tape Ⓐ front cover mounting screw (1). Front cover mounting screw 2.
- Page 9 Installation method - continuation ■ Fixing the base Power cord hole 1. Push the power cable for exclusive wiring through the power cord hole at the rear of the base. Power cable 2. Engage the base with the 2 hooks on the installation panel.
- Page 10 Installation method - continuation Caution Warning ● Make sure that the main unit ● Input Power: 120 Vac Single-phase is used. does not fall as the base is not attached to the wall with screws. Using the incorrect power supply may cause fi res, electric shocks Injuries may be caused if the unit or malfunctions.
- Page 11 Installation method - continuation ■ Checking the setting Customer is not allowed to change the setting. The installer should change the initial setting if necessary. ● The initial setting is as shown in the table below. ● Initial setting Type Heater JT-S1AP The unit cannot change the air speed.
-
Page 12: Checking After Installation
Checking after installation When fi nishing the installation work, check the items in the table below again. ● Be sure to solve a problem if any. (Otherwise the expected performance and safety cannot be ensured.) ■ Points to be checked Item Description Check... -
Page 13: Test Run
Test Run Step What to check for Check Is the proper power being used? Check the power supply Single-phase 120V AC voltage Incorrect power supply may cause malfunctions or low wind power. Turn the ground-fault circuit Are any lights in the display on? interrupter "ON"... - Page 14 MEMO − NA - 14 − － 14 －...