Table of Contents
Advertisement
en Basic operation
7.2 Cleaning the appliance before using it
for the first time
Before using the appliance to cook food for the first
time, you must clean the cooking compartment and ac-
cessories.
1.
Remove the product information and the accessor-
ies from the cooking compartment. Remove any
leftover packaging, such as polystyrene pellets, and
any adhesive tape either in or on the appliance.
2.
Wipe the smooth surfaces in the cooking compart-
ment with a soft, damp cloth.
3.
Press
to switch the appliance on.
4.
Apply the following settings:
Type of heating
8 Basic operation
8.1 Switching on the appliance
▶
Press
to switch the appliance on.
a The display shows the menu.
8.2 Switching off the appliance
Switch your appliance off when you are not using it.
The appliance automatically switches itself off if it is not
used for a certain period of time.
▶
Press
to switch the appliance off.
a The appliance switches off. Any functions currently
in progress are cancelled.
a The time or residual heat indicator appears on the
display.
8.3 Starting the operation
You must start each operation.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
▶
Do not use the appliance if there is water on the
cooking compartment floor.
▶
Wipe away any water on the cooking compartment
floor before operation.
▶
Use "Start" to start the operation.
a The settings appear on the display.
8.4 Interrupting the operation
You can interrupt the operation and then continue
again.
1.
To interrupt the operation, press "Stop".
2.
To continue the operation, press "Start".
8.5 Setting an operating mode
After you have switched on the appliance, the menu
appears on the display.
1.
To scroll through the various selection options,
swipe to the left or right on the display.
14
4D hot air
Temperature
Cooking time
→ "Basic operation", Page 14
5.
Start the operation.
Ventilate the kitchen while the appliance is heat-
‒
ing.
a Once the cooking time has elapsed, a signal tone
sounds. A note appears on the display confirming
that the operation has finished.
6.
Press
to switch the appliance off.
7.
Once the appliance has cooled down, clean the
smooth surfaces in the cooking compartment with a
detergent solution and a dish cloth.
8.
Clean the accessories thoroughly using a detergent
solution and a dish cloth or soft brush.
2.
To select a function, press the corresponding tile.
a Depending on the function, possible adjustment val-
ues or other tiles are available for selection.
3.
If required, press on another tile.
4.
To change the adjustment values:
Swipe over the blue adjustment line or push the
‒
adjustment line to the appropriate point.
Or press
and enter the value directly via the
‒
number field that appears.
5.
Use "Start" to start the operation.
6.
If the operation is ended:
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Tip: You can save your settings as "Favourites"
use these again.
→ "Favourites", Page 23
8.6 Setting the type of heating and the
temperature
1.
Press "Types of heating".
2.
Press the type of heating that you want to use.
3.
Set the temperature using the adjustment line or dir-
ectly via the number field
If required, you can implement additional settings:
– → "Rapid heating", Page 15
– → "Time-setting options", Page 16
– → "Microwave", Page 17
– → "Ventilation function Crisp Finish", Page 19
– → "Meat probe", Page 19
4.
Use "Start" to start the operation.
a The appliance starts heating.
a The adjustment values and how long the appliance
has already been in operation are shown on the dis-
play.
5.
When the food is ready, use
ance off.
Note: The most suitable type of heating for your food
can be found in the type of heating description.
Changing the type of heating
When you change the type of heating, the other set-
tings are also reset.
Maximum
1 hour
to switch the ap-
and
.
to switch the appli-
Advertisement
Table of Contents
