Sealey TIG180S.V3 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear protective
instructions
gloves
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the owner's responsibility to read, understand and comply with the following:
‰
You must check all electrical equipment and appliances to ensure that they are safe before use. You must inspect power supply leads,
plugs and all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of
appropriate safety devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We
also recommend that an RCD (Residual Current Device) is used with all electrical products. It is particularly important to use
an RCD with portable products that are plugged into an electrical supply not protected by an RCCB. If in doubt consult a
qualified electrician.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a
qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply.
See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
Ensure that cables are always protected against short circuit and overload.
Regularly inspect power supply, leads, plugs for wear and damage and all electrical connections
to ensure that none is loose.
Important: Ensure the voltage marked on the product is the same as the electrical power supply
to be used and check that supply is correctly fused, see fuse rating at right.
DO NOT pull or carry the powered appliance by its power supply lead.
8
DO NOT pull power plugs from sockets by the power cable.
8
DO NOT use worn or damaged leads, plugs or connections. Immediately replace or have
8
repaired by a qualified electrician.
This product comes without a plug. You must contact a qualified electrician to ensure an
adequate supply is available.
If fitting such a plug -
Ensure that the unit is correctly wired and earthed, as follows:
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check there are no bare wires, that all wires have been correctly connected, that the cable outer insulation is
clamped by the cable grip and that the grip is tight.
WARNING Be very cautious if using a generator to power the Inverter. The generator must be self regulating and stable with regard to
‰
voltage, waveform and frequency. The output must be greater than the power consumption of the inverter. If any of these requirements is
not met the electronics within the Inverter may be affected.
NOTE: The use of an unregulated generator may be dangerous and will invalidate the warranty on the inverter.
WARNING! The inverter may produce voltage surges in the mains supply which can damage other sensitive equipment (e.g.
‰
computers). To avoid this happening it is recommended that the Inverter is connected to a power supply that does not feed any
sensitive equipment.
1.2. GENERAL SAFETY
▲ DANGER Unplug the inverter from the mains power supply before connecting or disconnecting cables or performing maintenance or
service. Direct contact with the inverter circuit is dangerous.
Keep the inverter and cables in good working order and condition. (Take immediate action to repair or replace damaged parts).
9
Use genuine parts and accessories only. (Non recommended parts may be dangerous and will invalidate the warranty).
9
Locate inverter in an adequate working area for its function. Ensure area has adequate ventilation as welding fumes are harmful.
9
WARNING If it is necessary for you to assemble the work clamp cable, ensure that sufficient copper strands are exposed and turned
‰
back to make full contact within the dinse plug to ensure a good electrical contact. Loose connection will cause overheating, rapid
deterioration and loss in efficiency.
Ensure there is no obstruction to the flow of clean cool air through the ventilation apertures and ensure there are no conductive dusts,
9
corrosive vapours or humidity which could enter the inverter and cause serious damage.
© Jack Sealey Limited
TIG/MMA INVERTER WELDERS
MODEL NO'S:
Warning: Warning:
arc rays
electric shock
Original Language Version
TIG180S.V3, TIG200S.V3
Warning: Warning:
fumes and gases magnetic field
TIG180S.V3, TIG200S.V3 Issue 2 (1) 31/01/23
Warning:
fire risk
THIS PRODUCT REQUIRES A
MINIMUM 32 AMP
SUPPLY