Fujitsu D2509 Technical Manual
  1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Computer Hardware
  5. D2509
  6. Technical manual

Fujitsu D2509 Technical Manual

System board
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
System Board D2509
for TX200 S4
Technical Manual
Edition October 2007

Advertisement

Table of Contents
loading

Related Manuals for Fujitsu D2509

Summary of Contents for Fujitsu D2509

  • Page 1 System Board D2509 for TX200 S4 Technical Manual Edition October 2007...
  • Page 2 Gesellschaft für Technik-Dokumentation mbH www.cognitas.de Copyright and Trademarks Copyright © 2007 Fujitsu Siemens Computers GmbH. All rights reserved. Delivery subject to availability; right of technical modifications reserved. All hardware and software names used are trademarks of their respective manufacturers.

  • Page 3: Table Of Contents

    Replacing the lithium battery ....29 Abbreviations ....... 31 Technical Manual D2509 (TX200 S4)

  • Page 5: Introduction

    Introduction This technical manual describes the system board D2509, which can be ® equipped with one or two Intel XEON™ processors. Further information about drivers is provided in the readme files on the hard disk, on the supplied “ServerStart“ or “Update“ CDs.

  • Page 7: Important Notes

    Information on which system expansions are suitable can be obtained from the customer service centre or your sales outlet. ● The warranty expires if the device is damaged during the installation or replacement of system expansions. Technical Manual D2509 (TX200 S4)
  • Page 8 Incorrect replacement of lithium battery may lead to a risk of ● explosion. The batteries may only be replaced with identical batteries or with a type recommended by the manufacturer. It is essential to observe the instructions in chapter “Replacing the lithium battery”. Technical Manual D2509 (TX200 S4)
  • Page 9 Place all components on a static-safe base. ● You will find a detailed description for handling ESD components in the relevant European or international standards (EN 61340-5-1, ANSI/ESD S20.20). Technical Manual D2509 (TX200 S4)

  • Page 10: Ce Certificate

    Never use sharp objects (screwdrivers) for leverage. ● CE Certificate The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility". Compliance was tested in a typical PRIMERGY configuration. Technical Manual D2509 (TX200 S4)

  • Page 11: Environmental Protection

    Cd Cadmium Hg Mercury Pb Lead Notes on labeling plastic housing parts Please avoid attaching your own labels to plastic housing parts wherever possible, since this makes it difficult to recycle them. Technical Manual D2509 (TX200 S4)
  • Page 12 You will find further information on this at www.fujitsu- siemens.com/recycling. For details on returning and reuse of devices and consumables within Europe, refer to the “Returning used devices” manual, or contact your Fujitsu Siemens Computers branch office/subsidiary or our recycling centre in Paderborn: Fujitsu Siemens Computers...

  • Page 13: Features

    – Super I/O controller (SMSC 47M107) – 1 MB Flash BIOS – Server Management with FSC iRMC – VGA controller integrated in iRMC – 8MBx16 Flash for iRMC – 512KBx16 SRAM for iRMC – Thermal and system management controller (ADT7462) Technical Manual D2509 (TX200 S4)
  • Page 14 – 4x PCIe x4 slots (standard) – 2x PCIe x4 slots and 1x PCIe x8 slot (optional) – 2x PCIe x8 slots (optional) – 1 x PCI slot 32 bit / 33 MHz) Technical Manual D2509 (TX200 S4)
  • Page 15 SSI EEB Baseboard 304,8 x 330,2 mm (12 x 13 inch) CSS (Customer Self Service) This system board supports the CSS functionality. You will find a description of CSS functionality in the operating manual of your server. Technical Manual D2509 (TX200 S4)

  • Page 16: Main Memory

    FBD533/PC2-4200F or FDB667/PC2-5300 fully buffered DIMM modules and must be populated in pairs. It is only allowed you use memory modules released by Fujitsu Siemens Computers. – Each pair must consist of identical memory modules (2 way interleaved mode).

  • Page 17: Pci Slots

    PCI-X 64 Bit / 133 MHz IOOP Slot 4 PCI-X 64 Bit / 133 MHz IOOP Slot 3 PCI 32 Bit / 33 MHz Slot 2 PCIe x8 Slot 1 PCIe x8 Figure 3: Mechanical PCI slots Technical Manual D2509 (TX200 S4)
  • Page 18 An interrupt signal may thereby be used simultaneously by multiple devices (interrupt sharing). PCI Express devices send their interrupts through messages. The interrupts are defined by the system design. Technical Manual D2509 (TX200 S4)
  • Page 19 PCI_INTA, PCI_INTB, PCI_INTC, PCI_INTD Slot 1 PCIe x8 PCI_INTA, PCI_INTB, PCI_INTC, PCI_INTD Assignment of the PCI interrupts If you select Auto in the BIOS setup, the interrupts are assigned automatically and no further settings are required. Technical Manual D2509 (TX200 S4)

  • Page 20: Screen Resolution

    C temperature sensor. Fan monitoring The CPU, power supply unit and system fans are monitored. Fans that are no longer available, blocked or sticky fans are detected. Technical Manual D2509 (TX200 S4)
  • Page 21 LED and recorded in the System Event Log. They could be retrieved in the BIOS Setup or via ServerView. PRIMERGY Diagnostic LEDs Optical signaling through the LEDs on the system board identifies defective modules and components as well as gaining information on the PDA. Technical Manual D2509 (TX200 S4)

  • Page 22: Leds

    LEDs are only visible, if the cover of the server has been opened. If the server has been powered off (power-plugs must be disconnected) it is possible to indicate the faulty component by pressing the indicate CSS button. Technical Manual D2509 (TX200 S4)
  • Page 23 F - system fan running fans orange fan failure G - CPU fans fan running orange fan failure H - PCI card PCI card okay orange PCI card failure Technical Manual D2509 (TX200 S4)

  • Page 24: Interfaces And Connectors

    PCI-X 64 Bit / 133 MHz IOOP PCI 32 Bit / 33 MHz iRMC PCIe x8 PCIe x8 Figure 5: Schematic view of the system board D2509 1 = Printer (optional) 14 = Intrusion 2 = Power supply PWR1 15 = Floppy disk drive...

  • Page 25: External Ports

    The SATA SW RAID 5 functionality will be activated by installing a license key (RAID key). 3.7.1 External ports Figure 6: External ports of the system board D2509 1 = CSS LED (yellow) 6 = USB port Global Error LED (orange)
  • Page 26 Figure 7: LAN connector single-channel Gigabit LAN controller 1 LAN transfer rate green + transfer rate 10 Mbit/s yellow green transfer rate 100 Mbit/s yellow transfer rate 1000 Mbit/s 2 LAN link/activity green LAN connection no LAN connection flashing LAN transfer Technical Manual D2509 (TX200 S4)

  • Page 27: Settings With Switches

    The system boots from the “Flash BIOS floppy disk“ from drive A and reprograms the system BIOS on the board. The System BIOS is started with the system BIOS from the system board (default setting). Technical Manual D2509 (TX200 S4)
  • Page 28 To write and delete floppy disks, the write-protection in BIOS Setup must be disabled (in menu Security, the field Diskette Write must be set to Enabled). The floppy disk drive is write-protected. Floppy disks can be read, written and deleted (default setting). Technical Manual D2509 (TX200 S4)

  • Page 29: Replacing The Lithium Battery

    Ê Press the locking spring into direction of the arrow (1), so that the lithium battery jumps out of its socket. Ê Remove the battery (2). Ê Insert a new lithium battery of the same type into the socket (3) and (4). Technical Manual D2509 (TX200 S4)

  • Page 31: Abbreviations

    Automatic Server Recovery and Restart Advanced Technology Attachment Battery Backup Unit BIOS Basic Input Output System Baseboard Management Controller CMOS Complementary Metal Oxide Semiconductor COMmunication port Central Processing Unit Double Data Rate DIMM Dual In-line Memory Module Technical Manual D2509 (TX200 S4)
  • Page 32 EPROM Erasable Programmable Read Only Memory EMRL Embedded RAID Logic EVRD Enterprise VRD Hot-plug Controller In Circuit Emulation Integrated (intelligent) Drive Electronics Integrated Mirror Enhanced IOOP Intelligent Organization Of PCI IPMB Intelligent Platform Management Bus Technical Manual D2509 (TX200 S4)
  • Page 33 Light Emitting Diode Multi Processor Specification Non Maskable Interrupt Original Equipment Manufacturer OHCI Open Host Controller Interface Operating System Peripheral Components Interconnect Prefailure Detection and Analyzing Programmed Input Output Programmable Logic Device PS(U) Power Supply (Unit) Technical Manual D2509 (TX200 S4)
  • Page 34 Real Time Clock Serial Attached SCSI SATA Serial ATA SCSI Small Computer Systems Interface SDDC Single Device Data Correction SDRAM Synchronous Dynamic Random Access Memory SHDG Server Hardware Design Guide System Management Bus Server Management Mode Technical Manual D2509 (TX200 S4)
  • Page 35 Abbreviations Symmetrically Multi Processing UHCI Unified Host Controller Interface Universal Serial Bus Video Graphics Adapter Voltage Regulator Down Voltage Regulator Module Wired for Management Wake up On LAN Technical Manual D2509 (TX200 S4)
  • Page 37 Information on this document On April 1, 2009, Fujitsu became the sole owner of Fujitsu Siemens Compu- ters. This new subsidiary of Fujitsu has been renamed Fujitsu Technology So- lutions. This document from the document archive refers to a product version which was released a considerable time ago or which is no longer marketed.

Table of Contents