Sole Diesel SCO 11 Operator's Manual
  1. Manuals
  2. Brands
  3. Sole Diesel Manuals
  4. Control Panel
  5. SCO 11
  6. Operator's manual
Sole Diesel SCO 11 Operator's Manual

Sole Diesel SCO 11 Operator's Manual

Generator control panel
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Generator Control
Panel
Operator's Manual
SCO 5
SCO 10
SCO 11
U_CTSCO520_EN
Revision 0
Solé, S.A. C-243 b, km 2 · 08760 Martorell (Barcelona) ·Tel. +34 93 775 14 00 · www.solediesel.com · info@solediesel.com
Manual del operador. Panel de control del Generador.
Solé Diesel, S.A. C-24
Manual
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SCO 11 and is the answer not in the manual?

Questions and answers

Related Manuals for Sole Diesel SCO 11

Summary of Contents for Sole Diesel SCO 11

  • Page 1 Panel Operator’s Manual SCO 5 SCO 10 SCO 11 U_CTSCO520_EN Revision 0 Solé, S.A. C-243 b, km 2 · 08760 Martorell (Barcelona) ·Tel. +34 93 775 14 00 · www.solediesel.com · info@solediesel.com Manual del operador. Panel de control del Generador.

  • Page 3: Table Of Contents

    Section 2 – Technical data ........................6 Section 3 – Installation ........................7 3.1. SCO 5 panel installation......................... 7 3.2. SCO 10 and SCO 11 panel installation ..................7 Section 4 – SCO 5 panel operation ...................... 8 4.1. Buttons and indicators ........................8 4.2.
  • Page 4 Section 7 – Sensors and switches specifications ................44 Section 8 – Optional equipment......................46 8.1. Panel SCO 5 / Panel SCO 10 / SCO 11 Amperometric Pack ............. 46 8.2. SCO 10 Second Panel Kit ......................46 8.3. SCO 10 Third Panel Kit ......................... 47 8.4.

  • Page 5: Section 1 - Introduction To The Sco

    Introduction to the SCO Section 1 – Introduction to the SCO The SCO it is a control and protection panel used for generating sets; it shows the settings measured on its displays. The Unit is designed for easy use, for both installer and end-user alike. Remote control The SCO controller can be remotely controlled.

  • Page 6: Section 2 - Technical Data

    Section 2 – Technical data Technical Data Power supply SCO 5 SCO 10 SCO 11 Voltage supply 8 V to 36 V DC 8 V to 36 V DC 8 V to 36 V DC 60 mA to 12V DC...

  • Page 7: Section 3 - Installation

    Then, it is necessary to connect male connector (engine installation wire) to female connector (SCO 5). 3.2. SCO 10 and SCO 11 panel installation The controller must be mounted onto the switchboard door. Requested cutout size is: SCO 10: 175 mm x 115 mm.

  • Page 8: Section 4 - Sco 5 Panel Operation

    SCO 5 panel operation Section 4 – SCO 5 panel operation 4.1. Buttons and indicators POSITION BUTTON DESCRIPTION Graphic B/W display. 128 x 64 pixels. Alarm red LED. The LED will blink when there is one or more active warning or active shutdown alarm.

  • Page 9: Display Screens And Page's Structure

    SCO 5 panel operation 4.2. Display screens and page’s structure The displayed information is structured into "pages" and "screens". Use buttons ▲ or ▼ to change the screen page. Voltage (V) Power (kW) Frequency (Hz) Operation hours Engine speed (RPM) Voltage between pahses (V) Frequency (Hz) L1 Current (A)

  • Page 10: Alarms, Events And History

    SCO 5 panel operation Oil pressure (Bar) Coolant temperature (ºC) Fuel level* (%) Battery voltage (V) Total power (kWh) Total R power (kVarh) Alarms, events and history Return to the main screen 4.3. Alarms, Events and History The folowing list shows the type of events and alarms that may appear in the history. Events Warnings Shutdowns...

  • Page 11: Events List

    SCO 5 panel operation A symbol corresponding to an event appears on the display followed by a number that indicates the total number of hours of the engine in which the event occurred. 4.3.1. Events list SYMBOL DESCRIPTION Manual start: Engine was manually started by pressing button START in Manual mode.

  • Page 12: Warnings List

    SCO 5 panel operation 4.3.2. Warnings list Active warning: When a warning occurs, O04 Alarm and O15 Common Warning outputs will close and the red LED above STOP button will blink. Warning symbol will blink in the upper-right corner of the LCD and the proper warning symbol will be displayed in the history with running hours stamp. Active warning can’t be confirmed.
  • Page 13 SCO 5 panel operation Binary inputs (Negative signal “-”): Low oil pressure (I13) Remote Start/Stop or Exhaust temperature (I12) * High coolant temperature (I08) Emergency stop (I04) Binary outputs (Positive signal “+”): Buzzer (O10) Preheating (O05) Fuel feed pump (O07) Stop solenoid (O06) Starter (O05) Analog inputs:...
  • Page 14 SCO 5 panel operation SYMBOL DESCRIPTION Emergency stop: the binary input (IO4) is activated. Overspeed: The protection comes active if the speed is greater than 120 % of nominal engine RPM. Actual speed value is derived from genset frequency or is sensed directly using magnetic pick-up input. Underspeed: Low engine RPM.
  • Page 15 SCO 5 panel operation SYMBOL DESCRIPTION Generator Overfrequency: The genset frequency is out of limits given by setpoints G03 Generator Overfrequency Shutdown and G04 Generator Underfrequency Shutdown. Generator Underfrequency: The genset frequency is out of limits given by setpoints G03 Generator Overfrequency Shutdown and G04 Generator Underfrequency Shutdown.

  • Page 16: Connections Description

    SCO 5 panel operation 4.4. Connections description Code Terminal Signal type Description Color Analog input Oil pressure sensor Brown Analog input Coolant temperature sensor Grey Binary input Oil pressure switch Blue Binary input Exhaust temperature switch* Purple Black Binary output Alarm No wired Binary output...

  • Page 17: Section 5 - Sco 10 Panel Operation

    SCO 10 panel operation Section 5 – SCO 10 panel operation 5.1. Buttons and indicators GENSET CONTROL BUTTONS POSITION BUTTON DESCRIPTION START button. Works in MAN mode only. Press this button to initiate the start sequence of the engine. STOP button. Works in MAN mode only. Press this button to initiate the stop sequence of the genset.
  • Page 18 SCO 10 panel operation POSITION BUTTON DESCRIPTION MODE LEFT button. Use this button to change the mode. The button works only if the main screen with the indicator of currently selected mode is displayed. Note: This button will not work if the controller mode is forced by one of the binary inputs Remote OFF, Remote MAN, Remote AUT.

  • Page 19: Display Screens And Pages Structure

    SCO 10 panel operation 5.2. Display screens and pages structure The displayed information is structured into "pages" and "screens". Use PAGE button to switch over the pages. 1. The Measurement page consists of screens which display measured values like voltages, current, oil pressure etc., computed values like genset power, statistic data and the alarm list on the last screen.
  • Page 20 SCO 10 panel operation Binary Inputs – Binary signals from the genset to control panel. BI1: Remote control – Start or Stop • • BI2: Alarm / Temperature switch (shutdown) • BI3: Emergency STOP. • BI4: Alarm / Pressure switch •...

  • Page 21: Setpoint. Controller Information Screen

    SCO 10 panel operation 5.2.2. Setpoint. Controller information screen Enter Page Hold the ENTER and PAGE button at the Page same time. Page Page Enter If the panel is more than 5 seconds in a screen, it returns to initial screen automatically. In this case, you must begin all the procedure again.

  • Page 22: Setpoint. Maintenance Hours Change

    SCO 10 panel operation 5.2.3. Setpoint. Maintenance hours change When the following warning appears in the Alarm list screen of SCO 10: First of all you must carry out the maintenance tasks according to the Maintenance task table, attached in the end. You also can consult this information in the Warranty manual.

  • Page 23: History Log

    SCO 10 panel operation 5.2.4. History Log Page Page Enter To display all the screens shown below, you must press "ENTER”. Solé, S.A. C-243 b, km 2 · 08760 Martorell (Barcelona) ·Tel. +34 93 775 14 00 · www.solediesel.com · info@solediesel.com Operator’s manual.

  • Page 24: Alarms List

    SCO 10 panel operation 5.2.5. Alarms list Fault Reset Active unconfirmed alarm Active confirmed alarm Alarm desactivation 5.2.6. Display contrast adjustment Enter Enter Hold ENTER button and, ↑ or ↓at the same time. Solé, S.A. C-243 b, km 2 · 08760 Martorell (Barcelona) ·Tel. +34 93 775 14 00 · www.solediesel.com · info@solediesel.com Operator’s manual.

  • Page 25: Change Language

    SCO 10 panel operation 5.2.7. Change language If the panel is more than 5 seconds in a screen, it returns You must follow these steps to change the panel language. to initial screen automatically. In this case, you must begin all the procedure again.

  • Page 26: Alarm Management

    SCO 10 panel operation 5.3. Alarm management The following alarms are available: • Breaker open and cooling (BOC) • Warning • Shut down 5.3.1. Breaker open and cooling (BOC) When the control panel detects a problem related to the alternator. The panel stops the genset gradually.

  • Page 27: Genset Operation States

    SCO 10 panel operation 5.4. Genset operation states 5.4.1. Engine status list Init Autotest during controller power on Not ready Genset is not ready to start Prestart Prestart sequence in process, Prestart output is closed Cranking Engine is cranking Pause Pause between start attempts Starting Starting speed is reached and the Idle timer is running...
  • Page 28 SCO 10 panel operation Configurable Warning/BOC/Shutdown alarms on the inputs of IL-NT. IOM Bin Inp CONFIG. Configurable Warning/BOC/Shutdown alarms on the IL-NT-BIO8 CONFIG inputs of IG-IOM/IGS-PTM. ActCallCH1Fail Active call on channel 1 failed. ActCallCH2Fail Active call on channel 2 failed. RTC backup battery is flat BackupBatt ChargeAlt Fail...
  • Page 29 SCO 10 panel operation Shutdown alarm in case of lost connection to IG- Sd IOM Fail IOM/IGS-PTM module. Warning alarm in case of lost connection to IGL- Wrn RA15 Fail RA15 module. Wrong checksum of parameters. Happens typically after downloading new firmware or changing of the ParamFail parameter.

  • Page 30: Section 6 - Sco 11 Panel Operation

    SCO 11 panel operation Section 6 – SCO 11 panel operation 6.1. Buttons and indicators GENSET CONTROL BUTTONS POSITION BUTTON DESCRIPTION START button. Works in MAN mode only. Press this button to initiate the start sequence of the engine. STOP button. Works in MAN mode only. Press this button to initiate the stop sequence of the genset.
  • Page 31 SCO 11 panel operation POSITION BUTTON DESCRIPTION MODE LEFT button. Use this button to change the mode. The button works only if the main screen with the indicator of currently selected mode is displayed. Note: This button will not work if the controller mode is forced by one of the binary inputs Remote OFF, Remote MAN, Remote AUT.

  • Page 32: Display Screens And Page's Structure

    SCO 11 panel operation Light mode 6.2. Display screens and page’s structure The displayed information is structured into "pages" and "screens". Use PAGE button to switch over the pages. 4. The Measurement page consists of screens which display measured values like voltages, current, oil pressure etc., computed values like genset power, statistic data and the alarm...
  • Page 33 SCO 11 panel operation • Voltage between phases and neutral • Voltage between different phases • Genset frequency • Electric current / Phase current* *Para poder visualizar estos valores es necesario tener instalado el Pack Amperométrico. • Oil pressure •...
  • Page 34 SCO 11 panel operation • BI1: Alarm / Temperature switch. • BI2: Exhaust gas temperatura*. • BI3: Alarm / Pressure switch. • BI4: Remote control – Start / Stop. • BI5: Sd Override. • BI6: Delta Configuration. • E-Stop. Binary outputs – Binary outputs from the control panel to the genset.

  • Page 35: Setpoint. Controller Information Screen

    SCO 11 panel operation • The left column shows the active power of each pase and total current (if the amperometric kit is installed). • The middle column shows the power factor of each pase and total (if the amperometric kit is installed).

  • Page 36: Setpoint. Maintenance Hours Change

    SCO 11 panel operation Configuration Level Standard Advanced 6.2.3. Setpoint. Maintenance hours change Solé, S.A. C-243 b, km 2 · 08760 Martorell (Barcelona) ·Tel. +34 93 775 14 00 · www.solediesel.com · info@solediesel.com Operator’s manual. Generator Control Panel...

  • Page 37: History Log

    SCO 11 panel operation 6.2.4. History Log To display all screens shown below, you must press “ENTER”. Solé, S.A. C-243 b, km 2 · 08760 Martorell (Barcelona) ·Tel. +34 93 775 14 00 · www.solediesel.com · info@solediesel.com Operator’s manual. Generator Control Panel...

  • Page 38: Alarms List

    SCO 11 panel operation 6.2.5. Alarms list Number of alarms Active unconfirmed alarm Inactive unconfirmed alarm Active confirmed alarm ECU Alarms Solé, S.A. C-243 b, km 2 · 08760 Martorell (Barcelona) ·Tel. +34 93 775 14 00 · www.solediesel.com · info@solediesel.com...

  • Page 39: Display Contrast Adjustment

    SCO 11 panel operation 6.2.6. Display contrast adjustment Hold ENTER and UP or DOWN at the same time. If the panel is more than 5 seconds in a screen, it returns to initial screen automatically. In this case, you must begin all the procedure again.

  • Page 40: Alarm Management

    Wrong phase sequence There is a fix defined phase sequence in SCO 11 controller L1, L2, L3. When the phases are connected in different order (e.g. L1, L3, L2 or L2, L1, L3) the following alarms are detected: Solé, S.A.

  • Page 41: Genset Operation States

    SCO 11 panel operation ALI Gen Ph Rotation Opposite = wrong genset phase sequence. Hint: Phase sequence detection is active when voltage in all three phases is >50VAC and all phases’ angles are in the range 120° ± 20. Phase sequence alarm detection is 1 sec delayed avoiding transient effects.
  • Page 42 SCO 11 panel operation Failed genset start. SD Start Fail Failure of alternator for charging the battery. Wrn Charging Alternator Fail This alarm informs the operator that the supply Wrn Battery <>Voltatge voltage to the controller is too high or too low.

  • Page 43: Connections Description

    SCO 11 panel operation 6.5. Connections description Code Terminal Tipo de señal Description Color Analog Input Oil pressure sensor Brown Analog Input Coolant temperatura sensor Grey Analog Input Black Binary Input Coolant temperatura switch White Binary Input Exhaust temperatura switch...

  • Page 44: Section 7 - Sensors And Switches Specifications

    Sensors and switches specifications Section 7 – Sensors and switches specifications Coolant temperature sensor: Function table Temperature Resistance Tolerance Operating voltage: 6-24V (ºC) (ohm) (ohm) Operating current: <85mA, Pmax<0.25W 287.4 ±32.8 Operating temperature: -40°C to +120°C Measuring range: -40°C to +120°C ±13.5 Absolute max.
  • Page 45 Sensors and switches specifications Oil pressure sensor (two pole): Function table Pressure Resistance Tolerance Operating voltage: 6-24V (BAR) (ohm) (ohm) Operating current: >20mA, <85mA, Pmax<0.25W +3/-5 Operating temperature: -20°C to +100°C Measuring range: 0 – 10 BAR ±4 Absolute max. value: 30 BAR, max. 2 seconds. ±4 Protection: BODY IP 67 ±5...

  • Page 46: Section 8 - Optional Equipment

    Optional equipment Section 8 – Optional equipment 8.1. Panel SCO 5 / Panel SCO 10 / SCO 11 Amperometric Pack In order to measure the phase current, it is necessary to install the Amperometric Pack, supplied as an option. The necessary toroidal transformers are included in each pack and must be suitable for each genset set model.

  • Page 47: Sco 10 Third Panel Kit

    Optional equipment 8.3. SCO 10 Third Panel Kit The third panel kit consists of two remote SCO 10 panel, three communication cards (one for each panel) and a communication wire. To install the remotes panels, first connect the communication wires between the main SCO 10 panel and the remotes SCO 10 panel as shown below.

  • Page 48: Sco 11 Second Panel Kit

    To install the remote panel, first the communication cable must be connected between the main SCO 11 panel and the remote SCO 11 panel as shown below. It should be noted that the black- coloured wire of the communication cable at the remote SCO 11 end must be connected to ground.

  • Page 49: Sco 11 Third Panel Kit

    (red wire to the positive and black wire to the negative of the source). Connect to a power source (8 to 36 V). The third panel kit is only available in the SCO 11 model. It is not possible to operate the SCO 5 panel remotely through another SCO panel.

  • Page 50: Section 9 - Electrical Wiring Diagrams

    Electrical wiring diagrams electrica Section 9 – Electrical wiring diagrams Solé, S.A. C-243 b, km 2 · 08760 Martorell (Barcelona) ·Tel. +34 93 775 14 00 · www.solediesel.com · info@solediesel.com Operator’s manual. Generator Control Panel...
  • Page 51 SCO05 CPC PIN 14 To VN CPC PIN 13 To VL1 CPC PIN 12 To Terminal (-) CPC PIN 11 To BI1 (T08) CPC PIN 10 To AI1 (T14) CPC PIN 9 To BI3 (T13) CPC PIN 8 To AI2 (T15) CPC PIN 7 To Terminal (D+) CPC PIN 6...
  • Page 52 SCO05 CPC PIN 16 To VL1 CPC PIN 15 To VL3 CPC PIN 14 To VN CPC PIN 13 To VL2 CPC PIN 12 To Terminal (-) CPC PIN 11 To BI1 (T08) CPC PIN 10 To AI1 (T14) CPC PIN 9 To BI3 (T13) CPC PIN 8 To AI2 (T15)
  • Page 53 CPC PIN 2 To BI13 SCO 10 CPC PIN 12 To Terminal (-) 10 A CPC PIN 3 To Terminal (+) CPC PIN 6 To Starter Relay PIN 87 CPC PIN 7 To Terminal (D+) CPC PIN 1 To Fuel Feed Pump PIN 87 CPC PIN 5 To Preheating Relay PIN 87 CPC 16 PIN...
  • Page 54 CPC PIN 2 To BI13 CPC PIN 12 To Terminal (-) SCO 10 CPC PIN 3 To Terminal (+) 10 A To Starter Relay PIN 87 CPC PIN 6 CPC PIN 7 To Terminal (D+) CPC PIN 1 To Fuel Feed Pump PIN 87 CPC PIN 5 To Preheating Relay PIN 87 To Stop Solenoir Relay PIN 87...
  • Page 55 Amarillo/Yellow CPC PIN 3 Rojo/Red CPC PIN 2 Lila/Purple 10 A CPC PIN 1 Verde/Green INSTALACIÓN POSTERIOR SCO 11 MONOF. Revisión A DIBUJADO VERIFICADO FECHA CREACIÓN ÚLTIMA REVISIÓN Cable amarillo de T11 (BO2) al T15 (BO6) (Fuel/Stop Solenoid) PÁGINA MARC G.
  • Page 56 CPC PIN 4 2.5 A Amarillo/Yellow CPC PIN 3 Rojo/Red CPC PIN 2 Lila/Purple 10 A CPC PIN 1 Verde/Green INSTALACIÓN POSTERIOR SCO 11 TRIF. DIBUJADO Revisión A VERIFICADO FECHA CREACIÓN ÚLTIMA REVISIÓN PÁGINA MARC G. RUBEN D. 12/04/2022 16/09/2022...

  • Page 57: Section 10 - Overall Dimensions

    Overall dimensions electrica Section 10 – Overall dimensions Solé, S.A. C-243 b, km 2 · 08760 Martorell (Barcelona) ·Tel. +34 93 775 14 00 · www.solediesel.com · info@solediesel.com Operator’s manual. Generator Control Panel...
  • Page 58 PANEL COMAP SCO5 SOLÉ SCO 5 PANEL MATERIAL ACABADO TRATAMIENTO PRESENTACIÓN ESCALA DIBUJADO FECHA CREACIÓN VERIFICADO GRADO PRECISIÓN ÚLTIMA REVISIÓN 01/03/2023 VICTORG MEDIO P.IGLESIAS 26/07/2022 61972100S SOLÉ, S.A.
  • Page 59 PANEL SCO 10 BASADO EN CONFIGURACION 60973400S MATERIAL ACABADO TRATAMIENTO PRESENTACIÓN ESCALA DIBUJADO FECHA CREACIÓN VERIFICADO GRADO PRECISIÓN ÚLTIMA REVISIÓN MEDIO P.IGLESIAS 16/12/2016 3002 SOLÉ, S.A.
  • Page 60 PANEL COMAP SCO 11 SOLÉ SCO 11 PANEL MATERIAL ACABADO TRATAMIENTO PRESENTACIÓN ESCALA DIBUJADO FECHA CREACIÓN VERIFICADO GRADO PRECISIÓN ÚLTIMA REVISIÓN 01/03/2023 VICTORG P.IGLESIAS MEDIO 26/07/2022 62972100S SOLÉ, S.A.
  • Page 62 U_CTSCO520_EN Revision 1 06/2022...

This manual is also suitable for:

Sco 10Sco 5

Table of Contents