Advertisement
Energy
Star Rated
23, 35, 50 Pint and
50 Pint with Pump
HME021001N / HME020030N
HME021002N / HME020006N
HME021003N / HME020031N
HME021004N / HME020391N
Thank you for purchasing our appliance.
Please be sure to read the entirety of
this user manual carefully prior to using
this appliance. If you have any questions
regarding the use of this product,
please contact Customer Service
at homelabs.com/help
or help@homelabs.com
Advertisement
Table of Contents
Related Manuals for homelabs HME021001N
Summary of Contents for homelabs HME021001N
- Page 1 Energy Star Rated 23, 35, 50 Pint and 50 Pint with Pump HME021001N / HME020030N HME021002N / HME020006N HME021003N / HME020031N HME021004N / HME020391N Thank you for purchasing our appliance. Please be sure to read the entirety of this user manual carefully prior to using this appliance.
-
Page 2: Table Of Contents
Failure to keep the product in its original quality from the time of receipt may impede hOmeLabs’s ability to correct any legitimate problem and may limit the extent to which hOmeLabs may provide recourse. - Page 3 Congratulations on bringing home your new appliance! Don’t forget to register your product at homelabs.com/reg for updates, coupons, and other relevant information. Although greatly appreciated, product registration is not required to activate any warranty.
- Page 4 IMPORTANT NOTICE FOR FIRST TIME USE TURN ON PLEASE NOTE: “Continuous” mode, disabling TURN OFF CONTINUOUS MODE use of the “Continuous” mode is turned off. BEGIN USING “LEFT”/”RIGHT” BUTTONS SAVE THESE INSTRUCTIONS For Household Use Only To prevent injury to the user or other people and property damage, the following instructions must be followed 1.
-
Page 5: Important Safety Instructions
• • R32 REFRIGENT SAFETY INSTRUCTIONS (APPLIES TO: HME021001N HME021002N HME021003N HME021004N) • Servicing shall only be performed as recommended by the equipment manufacturer. Maintenance and repair refrigerants in accordance with industry standards. • Do not modify the length of the Power Cord or use an extension cord to power the unit. Do not share the outlet •... - Page 6 Important Safety Instructions • has a refrigerant leak. ISO 817 IMPORTANT NOTE: carefully before installing or operating your CAUTION new air conditioning unit. Keep this manual materials for future reference. 1. Transport of Equipment Containing Flammable Refrigerants Check the local transport regulations. 2.
- Page 7 Important Safety Instructions No Smoking signs shall be displayed. 7) Ventilated area Ensure that the area is an open space or that it is adequately ventilated before breaking into the system or conducting any hot work. There should be a degree of continuous ventilation while the work is being carried out.
- Page 8 Important Safety Instructions 8. Repair to Intrinsically Safe Components Do not apply any permanent inductive or capacitive loads to the circuit without ensuring that this will not exceed the permissible voltage and current for the unit in use. Intrinsically safe components are the only types that can be of refrigerant in the atmosphere from a leak.
- Page 9 Important Safety Instructions The system leak test shall be performed upon completion of charging, but should be done prior to commissioning. A follow up leak test shall be carried out before leaving the site. 14. Decommissioning Before carrying out this procedure, it is essential that the technician is completely familiar with the equipment and all necessary details.
-
Page 10: Parts Description
Parts Description FRONT REAR Control Panel Handle (Both Sides) Air Outlet Grille Air intake Grille / Air Filter Panel Continuous Drain Hose Outlet Bucket Water Level Power Cord Storage Bracket Window Pump Drain Hose Outlet (Only Applicable to HME021004N) Caster Power Cord Pump Drain Hose Power Plug... -
Page 11: Operation
Operation PLACEMENT More than • This unit may have been tilted or placed upside down during 15.75 in (40 cm) shipping. To ensure this device works properly, allow unit to sit upright for at least 24 hours before initial use. More than •... - Page 12 Operation CONTROL PANEL Controls the fan speed. Press to select HME021004N) Press to activate the “Pump” operation. either “High” or “Normal” fan speed. Set the fan control to “High” for maximum moisture removal When the humidity has NOTE: been reduced and quiet operation is Before starting Pump, make sure the preferred, set the fan control to “Normal”.
- Page 13 Operation Press to activate the continuous dehumidifying operation. The appliance will work continuously NOTE: and will not stop except that the Bucket is full. In “Continuous” mode, the buttons it will go on “Continuous” mode by are locked. default. This will disable use of the LED Display to turn off “Continuous”...
- Page 14 Operation REMOVING THE COLLECTED WATER 1. Use the Bucket NOTE: When the Bucket is full, remove the Bucket Do not use “Continuous Draining” when and empty it. the outdoor temperature is equal to or less than 32°F (0°C), otherwise the water will Water Outlet Press the Power Cord...
- Page 15 Operation ELECTRICAL INFORMATION 3. Pump Draining (Only applicable to HME021004N) • NOTE: • Make sure the connection is Hose Outlet tightly. tight and there is no leaking. • Attach the Pump Drain Hose (Outer diameter: 1/4 in; • If the Pump Hose drops when length: 16.4 ft) to the Pump Drain Hose Outlet.
-
Page 16: Care & Cleaning
Care & Cleaning CARE AND CLEANING OF THE DEHUMIDIFIER the Plug from the wall outlet before cleaning. Do not use bleach, cleaning supplies, or other abrasives. 1. Clean the Grille and Case • Do not splash water directly onto the main unit. Doing so may cause: an electrical shock, the insulation to deteriorate, or the unit to rust. -
Page 17: Troubleshooting
Troubleshooting Before contacting Customer Service, reviewing this list can save time. This list includes the most common PROBLEM CAUSE/SOLUTION • • Check the house fuse/circuit breaker box. not start • or Bucket is full. • Bucket is not in the proper position. •... -
Page 18: Warranty
These are our general terms for warranty service, but we always urge our customers to reach out to us with any issue, regardless of warranty terms. If you have an issue with a hOmeLabs product, please contact Customer Service at homelabs.com/help or help@homelabs.com. - Page 20 For Household Use Only Distributed by hOmeLabs™, LLC Summit, NJ 07901 help@homelabs.com homelabs.com/help All rights reserved, hOmeLabs™ Made in China.
Need help?
Do you have a question about the HME021001N and is the answer not in the manual?
Questions and answers
Bucket isn’t collecting water leaked
The hOmeLabs HME021001N bucket may not be collecting water for the following reasons:
- The back drain plug is removed, causing water to drain elsewhere.
- The bucket is not in the correct position. Ensure it is properly placed.
- If using a hose for drainage, it may be too long (over 5 feet) or have kinks, preventing proper drainage.
- The hose connection may be loose.
- The pump indicator may be blinking, which could indicate an issue with the pump (applicable to HME021004N).
Check these factors to resolve the issue.
This answer is automatically generated