Sealey LP100.V7 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Electrical
instruction
shock
manual
hazard
This product is not suitable for primary heating purposes.
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. If used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance Test)
tested.
Electrical safety information, it is important that the following information is read and understood.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9
Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse - see
9
fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
This product is fitted with a BS1363/A 3 pin plug.
9
If the cable or plug is damaged during use, switch the electricity supply off and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. GENERAL SAFETY
WARNING! failure to comply with the precautions and instructions provided with the heater can
‰
result in death, serious bodily injury and property loss or damage from the hazards of fire, explosion,
burning, asphyxiation, carbon monoxide poisoning and/or electric shock.
WARNING! Only persons who can understand and follow these instructions should use or service this heater. Not for home or
‰
recreational vehicle use.
WARNING! NOT to be used for the heating of habitable areas of domestic premises: for use in public buildings, refer to national
‰
regulations.
Only use outdoors or in well ventilated surroundings in a well ventilated area away from combustible materials.
9
For every kW it is necessary to have a permanent ventilation of 25cm x 25cm.
9
Never direct the hot air flow towards the cylinder.
9
Never use the heater without its cover.
9
DO NOT exceed 100W/m³ of free room. The minimum volume of the room must be larger than 100m³.
8
DO NOT use in cellars, basements or in any room below ground level.
8
DO NOT obstruct the inlet or outlet sections of the heater.
8
WARNING! DO NOT cover the heater.
‰
WARNING! some parts of the heater can become very hot and cause burns. Particular attention has to be given to where children and
‰
vulnerable people are present.
The heater must be placed where there is no risk of fire, the hot air outlet must be at least 3m from any flammable wall or ceiling and
9
must never be directed towards the gas bottle.
Turn off the gas supply at the cylinder valve after use.
9
Only use the propane gas pressure regulator and hose assembly supplied with the heater without alteration.
9
Gas cylinder must be used and kept in accordance with current regulations.
9
The gas bottle must be replaced according to safety rules and away from sources of ignition.
9
The gas hose must not be twisted or bent.
9
© Jack Sealey Limited
PROPANE SPACE HEATER 61,000-102,000BTU/HR
(18-30KW) SPACE WARMER®
MODEL NO:
Hot surfaces Do not cover
Original Language Version
LP100.V7
Keep dry
Recommended fuse rating
5Amp
LP100.V7 Issue 3 (H,2,3) 19/04/23