Table of Contents
Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
OVATION
TUB
™
HIGH GLOSS ACRYLIC SURFACE
MODELS: 2647.112 & 2647.212
USED WITH BATH WALLS: 3060BW1
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be
sure your installation conforms to local codes.
BEFORE YOU BEGIN....
Local building codes vary by location. Observe all local plumbing and building codes.
Your new bath is shipped to you after careful inspection. All you need to finish the installation are your selected fittings.
To ensure maximum performance and pleasure from this product, please follow the instructions and cautions.
GENERAL INSTALLATION INFORMATION ...
1. When installing the matching ovation bath walls (model 3060BW1), additional studs may be required.
Refer to those installation instructions prior to installing tub.
2. Ovation bath walls are to be installed over stud walls.
3. Bath may only be installed in a recess type installation.
4. It is recommended that the tub be set in a small bed of mortar or grout tocompensate for uneven floors.
Stringers will help level tub but will not provide adequate support.
5. Take extra care when driving nails or screw to avoid damaging the bath.
TOOLS & MATERIALS REQUIRED....
TOOLS:
• Level
• Square
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
NOTE: Take extra care in handling surfaces of the bath. Use only non-abrasive cloths to avoid scratching.
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 1 3
• Screw Driver
• Standard Woodworking Tools
• Personal Safety Equipment
• Caulking Gun
MATERIALS:
• Nails
• Plumber's Putty
• Silicone Sealant
• 1 x 3 or 2 x 4 Stringers
• Drop Cloth
• Mortar Mix or Grout
754916-100
Advertisement
Table of Contents
Related Manuals for American Standard OVATION 2647.112
Summary of Contents for American Standard OVATION 2647.112
- Page 1 USED WITH BATH WALLS: 3060BW1 Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
- Page 2 ROUGH-IN INFORMATION: OVATION TUB 60" (1524mm) 9-1/2" (241mm) 15" (381mm) 3-1/16" (78mm) 3-13/16" (97mm) 30" (762mm) 1-7/8" 33-3/4" (48mm) (857mm) C/L of pipe location from tub edge 3-1/2" (89mm) 3" 1" GENERAL SPECIFICATIONS FOR 2647 TUB (76mm) (25mm) INSTALLED SIZE 60 x 30 x 18 In.
- Page 3 A.) THIS BATH MUST BE SUPPORTED ALONG IT'S ENTIRE BOTTOM. We recommend the use of mortar as bedding material (sand is not recommended). Apply enough bedding to support the complete bottom of the bath. After the bedding has been poured, and before it sets, position the bath within the recess until the rim is leveled against the leveling stringers (see "Typical Recess Installation") shown below.
- Page 4 (30) days of purchase. In no event will American Standard be liable for the cost of repair or replacement of any installation materials including but not limited to tile, marble, etc. This limited warranty does not apply to Commercial Installations. The warranty for Commercial Installations is three (3) years.
Need help?
Do you have a question about the OVATION 2647.112 and is the answer not in the manual?
Questions and answers