Table of Contents
Advertisement
Register at www.Toro.com.
Original Instructions (EN)
TimeCutter
or 54in Riding Mower
Model No. 75747—Serial No. 412562015 and Up
Model No. 75747TA—Serial No. 400000000 and Up
Model No. 75747W—Serial No. 412090000 and Up
Model No. 75756—Serial No. 412515219 and Up
Model No. 75758TA—Serial No. 412540000 and Up
Model No. 75761TA—Serial No. 412600000 and Up
Form No. 3456-108 Rev A
®
MyRIDE
®
42in, 50in,
*3456-108*
Advertisement
Table of Contents
Related Manuals for Toro TimeCutter MyRIDE 75747
Summary of Contents for Toro TimeCutter MyRIDE 75747
- Page 1 Model No. 75747TA—Serial No. 400000000 and Up Model No. 75747W—Serial No. 412090000 and Up Model No. 75756—Serial No. 412515219 and Up Model No. 75758TA—Serial No. 412540000 and Up Model No. 75761TA—Serial No. 412600000 and Up *3456-108* Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Figure 1
Authorized Service manufacturer in accordance with the Society of Dealer or Toro Customer Service and have the model Automotive Engineers (SAE) J1940 or J2723. As and serial numbers of your product ready. -
Page 3: Table Of Contents
• Danger indicates an imminently hazardous Cleaning the Machine ........26 situation which, if not avoided, will result in death Pushing the Machine by Hand ......26 or serious injury. Transporting the Machine ......... 27 Maintenance ............29 • Warning indicates a potentially hazardous Maintenance Safety.......... -
Page 4: Safety
Safety This machine has been designed in accordance with ANSI B71.1-2017. General Safety This product is capable of amputating hands and feet and of throwing objects. Always follow all safety instructions to avoid serious personal injury or death. • Read and understand the contents of this Operator’s Manual before starting the engine. -
Page 5: Slope Indicator
Slope Indicator g011841 Figure 3 You may copy this page for personal use. 1. The maximum slope you can operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. -
Page 6: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. Decal 99-3943 is for models with 127 cm (50 inch) or 137 cm (54 inch) decks only. - Page 7 Decal 112-9840 is for models with 127 cm (50 inch) or 137 cm (54 inch) decks only. decal132-0872 132-0872 1. Thrown object 3. Severing hazard of hand hazard—keep bystanders or foot—keep away from away from the machine. moving parts. decal112-9840 112-9840 2.
- Page 8 decal139-2388 139-2388 3. Fast 1. Slow 2. Hauling Decal 139-2391 is for models without an hour meter. decal139-2392 139-2392 decal139-2394 139-2394 decal139-2391 139-2391 1. Traction controls 4. Neutral 2. Fast 5. Reverse 1. Fast 2. Slow 3. Slow 6. Parking brake...
- Page 9 decal139-2395 139-2395 1. Parking brake 4. Neutral 2. Fast 5. Reverse 3. Slow 6. Traction controls decal139-2397 139-2397 Decal 140-2717 is for models with an hour meter. decal140-2717 140-2717 1. Fast 2. Slow decal142-5864 142-5864...
- Page 10 decal132-0869 132-0869 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operator’s Manual as well as the conditions in which you would operate the machine to determine whether you can operate the machine in the conditions on that day and at that site.
-
Page 11: Product Overview
Product Overview g367815 Figure 4 1. Engine 4. Motion-control levers 7. Smart Speed™ lever 10. Rear drive wheel 2. Operator seat 5. Front caster wheel 8. Height-of-cut lever 11. Control panel 3. Fuel-tank cap 6. Deck-lift pedal (certain 9. Deflector 12. -
Page 12: Controls
Controls Motion-Control Levers Use the motion-control levers to drive the machine Become familiar with all the controls before you start forward, reverse, and turn either direction (Figure the engine and operate the machine. Park Position Control Panel Move the motion-control levers outward from the center to the P position when exiting the machine to engage the electric brake... -
Page 13: Specifications
Contact hair and do not wear loose clothing or loose your Authorized Service Dealer or authorized Toro jewelry. distributor or go to www.Toro.com for a list of all approved attachments and accessories. • Do not carry passengers on the machine. -
Page 14: Adding Fuel
Fuel Safety Adding Fuel • Fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and Recommended Fuel others and can damage property. Type Unleaded gasoline – To prevent a static charge from igniting the fuel, remove the machine from the truck or Minimum octane rating 87 (US) or 91 (research... -
Page 15: Performing Daily Maintenance
Understanding the Safety-Interlock System The safety-interlock system is designed to prevent the engine from starting unless: • The blade-control switch (PTO) is disengaged. • The motion-control levers are in the P position. The safety-interlock system also is designed to shut off the engine whenever the control levers are out of the P position and you rise from the seat. -
Page 16: Positioning The Seat
Positioning the Seat The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable (Figure g292102 Figure 9 1. MyRide adjustment lever 3. Firmer suspension 2. Softer suspension g027632 Adjusting the Figure 8... -
Page 17: During Operation
Contacting the blade can result in serious personal • Use only accessories and attachments approved injury. Shut off the engine, remove the key, and by Toro. wait for all moving parts to stop before leaving the operating position. When you turn the key to the •... - Page 18 • Clean grass and debris from the cutting unit, machine could suddenly roll over if a wheel goes drives, muffler, and engine to help prevent fires. over the edge or the edge collapses. Keep a safe distance (twice the width of the machine) between •...
-
Page 19: Operating The Mower Blade-Control Switch (Pto)
Towing Safety Operating the Mower • Do not attach towed equipment except at the hitch Blade-Control Switch (PTO) point. The blade-control switch (PTO) starts and stops the • Do not use the machine as a towing vehicle unless mower blades and any powered attachments. it has a hitch installed. -
Page 20: Operating The Throttle
Operating the Throttle Starting the Engine You can move the throttle control between the F Note: A warm or hot engine may not require choking. and S positions (Figure 17). Important: Do not engage the starter for more Always use the F position when engaging the PTO. -
Page 21: Shutting Off The Engine
Shutting Off the Engine Driving the Machine Disengage the blades by moving the The drive wheels turn independently, powered by blade-control switch to the O position. hydraulic motors on each axle. You can turn 1 side in reverse while you turn the other forward, causing Move the motion-control levers outward to the the machine to spin rather than turn. -
Page 22: Using The Smart Speed Tm Control System
Driving Backward Disengage the blade-control switch. Adjust the lever to the desired position. Move the levers to the center, unlocked position. To go backward, slowly pull the motion-control The following are only recommendations for use. levers rearward (Figure 22). Adjustments vary by grass type, moisture content, and the height of the grass. -
Page 23: Using The Side Discharge
Using the Side Discharge Adjusting the Height of Cut Note: The mower has a hinged grass deflector that The transport position is the highest disperses clippings to the side and down toward the height-of-cut position or cutting height at 114 mm turf. -
Page 24: Adjusting The Anti-Scalp Rollers
Adjusting the Anti-Scalp Machines with 127 cm (50-inch) or 137 cm (54-inch) Mower Decks Rollers Whenever you change the height of cut, adjust the height of the anti-scalp rollers. Machines with 107 cm (42-inch) Note: Adjust the anti-scalp rollers so that the rollers Mower Decks do not touch the ground in normal, flat mowing areas. -
Page 25: Operating Tips
Cutting more than that is not recommended unless damaged or worn, replace it immediately with a grass is sparse, or it is late fall when grass grows genuine Toro replacement blade. Refer to Servicing more slowly. the Cutting Blades (page 42). -
Page 26: After Operation
Pushing the Machine by After Operation Hand After Operation Safety This machine has an electric-brake mechanism, and to push the machine, the key must be in the position. The battery needs to be charged and General Safety functioning to disengage the electric brake. •... -
Page 27: Transporting The Machine
Transporting the Machine Use a heavy-duty trailer or truck to transport the machine. Use a full-width ramp. Ensure that the trailer or truck has all the necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you or bystanders avoid injury. - Page 28 If you are using a trailer, connect it to the towing vehicle and connect the safety chains. If applicable, connect the trailer brakes and lights. Lower the ramp, ensuring that the angle between the ramp and the ground does not exceed 15 degrees (Figure 28).
-
Page 29: Maintenance
Disconnect the cable from the negative terminal of the battery before repairing the machine. • To ensure optimum performance, use only genuine Toro replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be dangerous, and such use could void the product warranty. -
Page 30: Recommended Maintenance Schedule(S)
Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Check the safety-interlock system. • Check the engine-oil level. Before each use or daily • Inspect the blades. • Inspect the grass deflector for damage. • Clean grass and debris from the cutting unit, muffler, drives, grass catcher, and engine. -
Page 31: Lubrication
Lubrication Greasing the Bearings Service Interval: Every 25 hours—Grease the caster wheel bearings (more often in sandy soil conditions). Grease Type: No. 2 lithium grease Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the P position. -
Page 32: Engine Maintenance
Engine Maintenance Separate the foam and paper elements (Figure 34). Engine Safety • Keep your hands, feet, face, other body parts, and clothing away from the muffler and other hot surfaces. Allow engine components to cool before performing maintenance. • Do not change the engine governor speed or overspeed the engine. -
Page 33: Servicing The Engine Oil
Servicing the Paper Air-Cleaner Checking the Engine-Oil Level Element Service Interval: Before each use or daily Service Interval: Every 100 hours or yearly, Note: Check the oil when the engine is cold. whichever comes first—Replace the Important: If you overfill or underfill the engine paper air-cleaner element (more crankcase with oil and run the engine, you may often in dirty or dusty conditions). - Page 34 Changing the Engine Oil and Oil Filter Service Interval: Every 100 hours or yearly, whichever comes first—Change the engine oil and oil filter (more often in dirty or dusty conditions). Park the machine on a level surface to ensure that the oil drains completely. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the P...
-
Page 35: Servicing The Spark Plug
Servicing the Spark Plug Service Interval: Every 100 hours or yearly, whichever comes first—Check the spark plug(s). Every 200 hours/Every 2 years (whichever comes first)—Replace the spark plug(s). Ensure that the air gap between the center and side electrodes is correct before installing the spark plug. Use a spark plug wrench for removing and installing the spark plug and a gapping tool or feeler gauge to check and adjust the air gap. -
Page 36: Cleaning The Blower Housing
Fuel System Maintenance DANGER In certain conditions, fuel is extremely flammable and highly explosive. A fire or g206628 explosion from fuel can burn you and others Figure 41 and can damage property. Refer to Fuel Safety (page 14) for a complete list of fuel related precautions. -
Page 37: Electrical System Maintenance
Electrical System Maintenance Electrical System Safety g365941 • Disconnect the cable from the negative terminal of the battery before repairing the machine. • Charge the battery in an open, well-ventilated area, away from sparks and flames. Unplug the charger before connecting or disconnecting the battery. - Page 38 Charging the Battery WARNING Incorrectly removing the cables from Service Interval: Before storage—Charge the battery and disconnect the battery cables. battery could damage the machine and cables, causing sparks. Sparks can Remove the battery from the chassis; refer to cause the battery gasses to explode, Removing the Battery (page 37).
-
Page 39: Servicing The Fuses
Servicing the Fuses Drive System Maintenance The electrical system is protected by fuses. It requires no maintenance; however, if a fuse blows, check the component/circuit for a malfunction or short. Checking the Tire Pressure Fuse type: • Main—F1 (25 A, blade-type) Service Interval: Every 25 hours—Check tire pressure. -
Page 40: Releasing The Electric Brake
Releasing the Electric Rotate the bolt to decrease the speed for that particular wheel. Brake Note: Rotate the bolt a small amount to make minor adjustments. You can manually release the electric brake by rotating the link arms forward. Once the electric brake is energized, the brake resets. -
Page 41: Belt Maintenance
2. Nut and frayed edges, burn marks, and cracks on the belt. Replace the mower belt if any of these conditions are Using a spring-removal tool (Toro Part No. evident. 92-5771), remove the idler spring from the deck Park the machine on a level surface, disengage... -
Page 42: Mower Maintenance
(Figure 52 Figure 53). the blade-control switch, and move the Using a spring-removal tool (Toro Part No. motion-control levers outward to the P 92-5771), install the idler spring over the deck position. hook and place tension on the idler pulley and... - Page 43 g006530 Figure 54 1. Cutting edge 3. Wear/slot forming g014973 Figure 56 2. Curved area 4. Crack 1. Blade (in position for measuring) 2. Level surface Checking for Bent Blades 3. Measured distance between blade and the surface (A) Note: The machine must be on a level surface for Rotate the same blade 180 degrees so that the following procedure.
- Page 44 g014973 Figure 58 g027833 1. Opposite blade edge (in position for measuring) Figure 59 2. Level surface 1. Sail area of the blade 3. Curved washer 3. Second measured distance between blade and surface (B) 2. Blade 4. Blade bolt If the difference between A and B is greater than 3 mm (1/8 inch), replace the blade with Sharpening the Blades...
-
Page 45: Leveling The Mower Deck
Installing the Blades Install the blade onto the spindle shaft (Figure 59). Important: The curved part of the blade must be pointing upward toward the inside of the mower to ensure proper cutting. Install the curved washer (cupped side toward the blade) and the blade bolt (Figure 59). - Page 46 Leveling from Side to Side Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the Move to the left side of the machine. operating position. Set the anti-scalp rollers to the top holes or Set the height of cut to 76 mm (3 inches).
- Page 47 g294195 Figure 69 Install the washer and hairpin cotter (Figure 69). g298028 Repeat steps through for the other side of Figure 67 the machine. Mower Decks with 3 Blades Check the side-to-side level again; repeat this 1. Wood block—6.6 cm 2.
-
Page 48: Removing The Mower Deck
To lower the front of the mower deck, loosen the adjustment nut. After adjustment, check the front-to-rear slope again, continue adjusting the nut until the front blade tip is 1.6 to 7.9 mm (1/16 to 5/16 inch) lower than the rear blade tip; refer to Checking the Front-to-Rear Blade Slope (page 45). -
Page 49: Replacing The Grass Deflector
Attach the front support rod to the mower deck Slide the rod through the second grass-deflector with the clevis pin and hairpin cotter (Figure 71). pivot (Figure 73). Install the mower belt onto the engine pulley; Insert the rod at the front of the grass deflector refer to Replacing the Mower Belt (page 41). -
Page 50: Cleaning
Cleaning Disengage the blade-control switch, shut off the engine, remove the key, and wait for all moving parts to stop. Washing the Underside of Turn the water off and remove the coupling from the washout fitting. the Mower Deck Note: If the mower is not clean after 1 washing, Service Interval: After each use—Clean the soak it and let it stand for 30 minutes. -
Page 51: Storage
Storage Note: Run the machine with the blade-control switch (PTO) engaged and the engine at high idle for 2 to 5 minutes after washing. Storage Safety Check the condition of the blades; refer to Servicing the Cutting Blades (page 42). •... -
Page 52: Storing The Battery
Storing the Battery Fully charge the battery. Let the battery rest for 24 hours, then check the battery voltage. Note: If the battery voltage is below 12.6 V, repeat steps and 2. Disconnect the cables from the battery. Check the voltage periodically to ensure that the voltage is 12.4 V or higher. -
Page 53: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The fuel tank is showing signs of collapsing 1. The air-cleaner paper element clogged. 1. Clean the paper element. or the machine is frequently showing signs of running out of fuel. The engine overheats. 1. - Page 54 Problem Possible Cause Corrective Action The machine does not drive. 1. The bypass valves are open. 1. Close the tow valves. 2. The traction belts are worn, loose, or 2. Contact an Authorized Service Dealer. broken. 3. The traction belts are off the pulleys. 3.
-
Page 55: Schematics
Schematics g307974 Electrical Diagram 139-2356 (Rev. A) - Page 56 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.