Sealey ES450.V2 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear safety
instructions footwear
1. SAFETY
WARNING! Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to
‰
when using this equipment.
Before using the stand ensure it is in good working order.
9
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Keep the stand clean for best and safest performance.
9
Locate the stand in a suitable work area, keep area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
9
Use on a firm, level surface capable of sustaining the stand and the load.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Ensure all non-essential persons keep a safe distance whilst the stand is in use.
9
Lock mounting plate in position with locking pin before fixing a load and ensure the load is centred and securely mounted on the
9
mounting plate.
When an engine is mounted, take the weight of the engine on the handle before removing the locking pin.
9
Ensure the stand and load are stable.
9
To move a loaded stand, steady the load and push from behind the main post of the stand so that the castor wheels are ahead of the load.
9
DO NOT pull the unit backwards, or push from the side, as this may cause the stand to tip.
8
Ensure surface over which the stand is to travel is strong enough to take the stand and load and that it is not cracked, uneven or obstructed.
9
DO NOT use unit if damaged.
8
DO NOT allow untrained persons to use the stand.
8
DO NOT exceed the rated capacity of 450kg.
8
▲ DANGER! DO NOT work under an engine mounted on the stand.
DO NOT use the stand for purposes other than those for which it is designed.
8
When not in use store stand in a safe, dry, childproof area.
9
2. INTRODUCTION
These stands accept a wide variety of engines and transmissions. The heads swivel 360° for accessibility to all parts of the engine. Fully
adjustable mounting arms. Swivel castors provide excellent manoeuvrability. Additionally Model No. ES900F features folding legs for easier
storage and transport.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . ES450.V2
Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450kg
Width: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 950mm
Depth: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 790mm
Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 930mm
Nett Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.9kg
4. ASSEMBLY
NOTE: All the following numbers refer to (figs.1, 2 & 3) overleaf.
4.1. Remove mounting plate (5) from main post (1).
4.2. Loosely attach main post (1) to side leg (3) with bolts (24), washers (12 & 25) and nuts (15).
4.3. Slide main beam (20) into base of main post (1) and loosely secure with bolt (4).
NOTE: Main beam (20) must be assembled with bracket (A) as shown.
4.4. Fit castor leg (21) to main beam (20) with bolts (24), washers (12 & 25) and nuts (15).
NOTE: Castor leg (21) must be fitted with castor mounting holes facing downward.
4.5. Tighten all nuts/bolts.
4.6. Fit castors (14) to castor leg (21) with nuts (10) and washers (11 & 17).
4.7. Slide wheels (Fig.2.23) onto pins on wheel leg (3) and retain with washers (17) and locking clip (19).
NOTE: Wheel hubs are not symmetrical - fit with longer hub inward.
4.8. Refit mounting plate (5) to main post (1) and locate with locking pin (6).
4.9. Attach the four mounting arms (Fig.3.7) to mounting plate (5) with bolts (8), washers (9 & 11) and nuts (10).
4.10. Insert handle (26, NOT SHOWN) through hole in stem of mounting plate (5).
© Jack Sealey Limited
ENGINE STAND 450KG
MODEL NO:
Wear protective Wear protective
gloves clothing
Original Language Version
ES450.V2
ES450.V2 | Issue 2 (H,F) 29/10/18