Sealey ES900F.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction
manual
1. SAFETY

WARNING! Ensure all health and safety, local authority, and general workshop practice regulations are strictly adhered to when using this
equipment.
Before using the stand ensure it is in sound condition and good working order.

Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.

Keep the stand clean for best and safest performance.

Locate the stand in an adequate working area for its function, keep area clean and tidy and free from unrelated materials and ensure

there is adequate lighting.
Use on a firm, level surface capable of sustaining the stand and the load.

Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery. Contain and/or tie back long hair.

Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

Ensure all non-essential persons keep a safe distance whilst the stand is in use.

Lock mounting plate in position before fixing a load and ensure the load is centred and securely mounted on the locking plate.

Ensure the stand and the load are stable.

To move a loaded stand, push it from the load side. DO NOT move the stand from the handle end and never pull the stand towards

yourself. Also ensure surface over which the stand is to travel is strong enough to take the stand and load and that it is not cracked,
uneven or obstructed.
Keep hands clear of moving parts when folding and unfolding the stand.

Wear appropriate protective clothing.

DO NOT operate unit if damaged.

DO NOT allow untrained persons to operate the stand.

DO NOT exceed the rated capacity of 900kg.

DO NOT use the stand when you are tired or under the influence of alcohol, drugs or intoxicating medication.


DANGER: DO NOT work under an engine mounted on the stand.
DO NOT use the stand for purposes other than for which it is designed.

WARNING! Failure to comply with these instructions may result in damage to the stand, load and/or personal injury.

When not in use store stand in a safe, dry, childproof area.

2. INTRODUCTION
These stands accept a wide variety of engines and transmissions. The heads swivel 360° for accessibility to all parts of the engine. Fully adjustable
mounting arms. Swivel castors provide excellent manoeuvrability. Additionally Model No. ES900F features folding legs for easier storage and
transport.
pec
3. SPECIFICATION
Model No: ....................................................................ES900F
Capacity: .........................................................................900kg
Size (W x D x H): ..................................... 1105 x 820 x 910mm
4. ASSEMBLY
Refer to fig.1 overleaf
Bolt the large castor wheels (9) to the rear-most mountings on the main frame and to the legs using M8x20 bolts (4), M8 washers (3),
4.1.
M8 lock washers (2) and M8 nuts (1). Bolt the small castor wheels (14) to the forward mountings on the main frame using
M8x14 bolts (10), M8 washers (3), M8 lock washers (2) and M8 nuts (1).
Assemble the legs to the frame using the Ø16x110 pins (11). Lay each leg into the open channel and insert the first pin into the hole
4.2.
nearest the rear of the frame. This will be the folding leg pivot. Retain the pin with a 'R' clip (15). Lock the leg in the down position by
inserting a second Ø16x110 pin (11) into the hole nearest the open end of the channel and retain with a 'R' clip (15).
Bolt the main upright to the cross member between the open channels using two M14x100mm bolts (8), M14 washers (7), M14 lock
4.3.
washers (6) and M14 nuts (5). DO NOT fully tighten the nuts at this stage.
Take the two support struts and loosely bolt them to the top of the main upright using a M14x100 bolt (8). Insert two M14 bolts (8)
4.4.
through the angled parts of the main base in the holes adjacent to the rear square section ensuring that the bolt heads are on the outside
of the frame. Slide the bottom of each support strut over the end of each bolt in turn and secure with the nuts and washers provided.
Fully tighten all the nuts and bolts holding the main upright and struts.
© Jack Sealey Limited
FOLDING ENGINE STAND 900kg
ES900F.V2
MODEL NO:
Wear safety footwear
Original Language Version
ES900F.V2 Issue: 2(H,F) - 28/03/18