Bushnell GOLF Tour V6, Tour V6 Shift - Laser Rangefinder Manual

INTRODUCTION

You are joining 98.6% of Tour players that trust their games to Bushnell Golf. The Tour V6 Series is packed with new and upgraded features. We have completely upgraded our electronic components, making the Tour V6 the most accurate, consistent, and fastest Tour Series Laser ever. Along with all the upgraded electronics, your Tour V6 features PinSeeker with Visual JOLT, BITE magnetic cart mount, and upgraded weatherproofing to IPX6.

AS WITH ANY LASER DEVICE, IT IS NOT RECOMMENDED TO DIRECTLY VIEW THE EMISSIONS FOR LONG PERIODS WITH MAGNIFIED LENSES.

PARTS GUIDE

1. Slope Switch (Shift model only)
2. Mode Button
3. Power/Fire Button
4. Eyepiece Diopter Dial
5. Battery Compartment 5
6. BITE Magnet (see inset photo)

DISPLAY INDICATORS

The Tour V6 display incorporates the following indicators:

1. Aiming Circle (surrounding crosshairs indicate laser transmission)
2. Distance Units (Yards/Meters)
3. Battery Level 2
4. "Play As" Distance, based on Slope (Shift model only)
5. Slope (% grade) (Shift model only) 3
6. Line of Sight Distance
7. Visual JOLT Indicator Ring

ACTIVATING/REPLACING THE BATTERY

Please remove the battery door by lifting the battery door tab and rotating counterclockwise until it is loose. Then, activate the installed CR2 3-volt lithium battery by removing the battery door as described above. Next, remove the plastic protective disc from the top of the battery, and replace the door.
Replacing a low battery: Insert a new CR2 3-volt lithium battery into the compartment negative (flat) end first (positive end facing out towards the battery cover), then replace the battery door.

BATTERY LEVEL INDICATOR

The Battery Indicator (3) shows the remaining power level:

• Full charge
• Approx. 2/3 battery life remaining
• Approx. 1/3 battery Life remaining
• Battery Indicator Blinks - Battery needs replacing, and the unit will not be operable.

THIS PRODUCT USES A LITHIUM BASED BATTERY. LITHIUM BATTERIES CAN OVERHEAT AND CAUSE DAMAGE IF PHYSICALLY ABUSED. DO NOT USE BATTERIES THAT ARE DAMAGED OR SHOW SIGNS OF PHYSICAL WEAR.

BASIC OPERATION

While looking through the Tour V6, depress the Power/Fire button once to activate the display. If the display icons and numbers are blurry, rotate the eyepiece in either direction until they are in focus (see "Adjusting the Eyepiece" below).

1. Place the aiming circle (center of the display) over a target at least 5 yards away. Press and hold the Power/Fire button until the "line of sight" distance displays near the bottom of the display (see "Display Indicators" below). Crosshairs surrounding the aiming circle indicate that the laser is transmitted.
2. After a range is acquired and displayed, you can release the Power/Fire button. The crosshairs surrounding the aiming circle will disappear once the Power/Fire button is released (i.e., the laser is no longer transmitting).
3. Once activated, the display will remain visible and display the last distance measurement for 10 seconds. Press the Power/Fire button again to range to a new target. The maximum time the laser is transmitted (active) is 5 seconds. To re-fire, press the button down again.

ADJUSTING THE EYEPIECE

The Tour V6 is equipped with an adjustable Fast Focus eyepiece (+/- 3.5 diopter adjustment) that allows you to focus the displayed data and icons relative to the viewed image from the monocular optics. Rotate the eyepiece until the display is in focus.

ACTIVE LASER

Crosshairs surrounding the aiming circle indicate that the laser is transmitted. Once a range is acquired, you can release the Power/Fire button. The crosshairs surrounding the circle will disappear once the Power/Fire button is released (i.e., the laser is not transmitting).

SLOPE SWITCH TECHNOLOGY (TOUR V6 SHIFT ONLY)

Slope-Switch Technology lets the golfer easily turn Bushnell's patented Slope function on and off. The switch allows the golfer to conveniently utilize Slope to get compensated distances around the course when they want it and have a USGA conforming device that is legal for tournament play when they need it. Slope mode is enabled by sliding the Slope Switch on the side of the Tour V6 Shift (model# 202321) to the left so the orange Slope indicator is visible (see photo, right) and Bushnell's patented Slope Technology is displayed. The Slope +/- mode will automatically compute an angle compensated range based on distance and Slope determined by the laser rangefinder and built-in inclinometer. This data is combined with internal algorithmic formulas dealing with average club use and ball trajectories. The angle compensated range provides direction on how to play the shot (i.e., add distance if an incline, subtract distance if a decline). Slide the Slope Switch right, and the Tour V6 now conforms to USGA Rule 14-3, with the Slope compensated ranging feature removed.

HOW TO USE SLOPE +/-™ (TOUR V6 SHIFT ONLY)

Move the Slope switch to the "Slope On" position. A second row of information appears in the display, confirming that you are now in slope mode. Next, press the Power/Fire button to obtain the distance to the flag or other objects. Once the range is displayed, release the Power/Fire button. Once the Power/Fire button is released, the grade percentage and compensated range will be displayed beneath the standard distance in the second row of numbers. For example, if the true distance is 160 yards, but with a slope of +6 percent, the Slope compensated ("play-as") range is 168 yards. The display would show this (right):

THE ADVANTAGE OF SLOPE +/-™ (TOUR V6 SHIFT ONLY)

The distance to the black flag in the drawing (see below) is 160 yards. It is also 160 yards to the red flag, although it is on a slope with a 6% grade (uphill incline). However, if a golfer were to play this hole as 160 yards, the ball (X) would fall short of the hole/flag if slope was not taken into account. Therefore, due to the slope, it should be played as a 168 yard shot. This distance displays the "play as" distance below the line of sight distance.

SETTING DISTANCE UNITS (Y OR M) & JOLT PREVIEW

To set the distance between Yards or Meters, press Fire/Power to turn the unit on, then press and hold the Mode button until the display blinks. Press the Mode to switch from Y (yards) or M (meters). Press Fire/Power button to set the distance units.
This action initiates JOLT (vibration and visual ring in display), allowing you to preview/demo the effect of JOLT Technology without requiring you to fire the laser at a target.

USING PINSEEKER™ WITH VISUAL JOLT®

Bushnell's exclusive Pinseeker™ feature allows reliable flag targeting without inadvertently getting distances to large background targets (i.e., trees, club houses, etc.) with stronger signal strength. When ranging your target, if the laser beam recognizes more than one object (i.e., the flag and a group of trees behind it), only the distance to the closest object (the flag) will be displayed. The JOLT Technology provides two short bursts of vibration to confirm that the distance displayed is to the flag, and the red ring (Visual JOLT Indicator) around the outer edge of the display is activated, confirming the laser has ranged the correct target via Pinseeker. Occasionally, the laser will only see one object in its path. In this instance, JOLT will not signal.
Tip: While pressing the Power/Fire button, you can move the device slowly from object to object and intentionally force the laser to hit multiple objects to ensure that you are only displaying the closest of the objects recognized by the laser. Once the device has shut off, the unit will always default to the last mode used.

BITE MAGNETIC MOUNT

The Tour V6 features a powerful BITE magnet incorporated into the right side of its housing, which allows the device to be securely attached to a golf cart bar or frame. Be sure to attach the rangefinder to the cart frame with the eyepiece at the one o'clock position. This positioning will ensure the magnet is properly aligned and engaged with the cart bar.

THE BITE FEATURE INCLUDED WITH THE DEVICE CONTAINS A NEODYMIUM MAGNET. MAGNETS COULD AFFECT THE FUNCTIONING OF PACEMAKERS AND IMPLANTED HEART DEFIBRILLATORS. IF YOU USE THESE DEVICES, KEEP A SUFFICIENT DISTANCE FROM THE MAGNET. ALSO, WARN OTHERS WHO WEAR THESE DEVICES FROM GETTING TOO CLOSE TO MAGNETS.

• A magnet may permanently lose part of its adhesive force if exposed to temperatures above 175º F (80º C).
• Magnets produce a far-reaching, strong magnetic field. They could damage TVs, laptops, computer hard drives, credit and ATM cards, data storage media, mechanical watches, hearing aids, and speakers. Keep the unit away from devices and objects that strong magnetic fields could damage.
• Magnets have strong magnetic fields which can pinch skin and fingers. So use caution when attaching the unit to a metal bar.

CLEANING AND GENERAL CARE

Your Bushnell Tour V6 laser rangefinder lenses are fully multi-coated for the highest light transmission. However, as with multi-coated optics, take special care to clean the lenses. Follow these tips for proper lens cleaning:

• Blow away any dust or debris on the lens (or use a soft lens brush).
• To remove dirt or fingerprints, clean with the supplied microfiber cloth rubbing in a circular motion. Using a coarse cloth or unnecessary rubbing may scratch the lens surface and cause permanent damage. The included washable microfiber cleaning cloth is ideal for cleaning your optics. First, breathe lightly on the lens to provide slight moisture, then gently rub the lens with the microfiber cloth.
• For a more thorough cleaning, photographic lens tissue and photographic-type lens cleaning fluid or isopropyl alcohol may be used. Always apply the fluid to the cleaning cloth – never directly on the lens.
• The rangefinder is water resistant but should not be exposed to heavy rain or other direct streams of water and will not withstand submersion in water or other liquids.

Use caution to avoid direct sunlight into the eyepiece to prevent damage to the display/internal components. When using the BITE magnet to attach the device to a cart bar or frame, tilt the device so the eyepiece aims towards the ground, not pointed upwards towards the sun. When you are not using the device, please store it in the case for additional protection.

TROUBLESHOOTING

NEVER DISASSEMBLE YOUR LASER RANGEFINDER. IRREPARABLE DAMAGE CAN RESULT FROM UNAUTHORIZED SERVICE ATTEMPTS, VOIDING THE WARRANTY.

If the unit does not turn on or the display does not illuminate:

• Depress Power/Fire button.
• Check and, if necessary, replace the battery. If the unit does not respond to button presses, replace the battery with a good quality CR2 3-volt Lithium battery.

If the unit powers down (the display goes blank when attempting to power the laser):

• The battery is either weak or low quality. Replace the battery with a new 3-volt lithium battery (CR2).

If target range cannot be obtained

• Ensure the display is illuminated.
• Make sure that the Power/Fire button is being depressed.
• Ensure that nothing, such as your hand or finger, is blocking the objective lenses (lenses closest to the target) that emit and receive the laser pulses.
• Make sure the unit holds steady while depressing the Power/Fire button.
  NOTE: The last range reading does not need to be cleared before ranging another target. Aim at the new target using the display reticle, depress the Power/Fire button, and hold until the new range reading is displayed.

TECHNICAL SPECIFICATIONS

AS WITH ANY LASER DEVICE, IT IS NOT RECCOMENDED TO DIRECTLY VIEW THE EMISSIONS FOR LONG PERIODS OF TIME WITH A MAGNIFIED LENS.

FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device does not contain any user-serviceable parts. Repairs should only be made by an Authorized Bushnell Repair center. Unauthorized repairs or modifications could result in permanent damage to the equipment, and will void warranty and your authority to operate the device under Part 15 regulations. Specifications and design are subject to change without any notice or obligation on the part of the manufacturer.

FDA SAFETY
Complies with 21CFR1040.10 and 1040.11 except for conformance with IEC60825-1 Ed.3., as described in Laser Notice 56, dated May 8, 2019.

There are no user controls, adjustments or procedures. Performance of procedures other than those specified herein may result in access to invisible laser light.
This product contains no user serviceable controls.
This product must not be opened or modified by the consumer.
This product must be returned to the manufacturer for service.

Device specifications and design are subject to change without notice or obligation on the part of the manufacturer.

CAN ICES-3B/NMB-3B

Industry Canada Statement
This device complies with ISED's licence-exempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement
This device complies with the Industry Canada portable RF exposure limit set forth for an uncontrolled environment and is safe for the intended operation as described in this manual. Further RF exposure reduction can be achieved if the product can be kept as far as possible from the user's body or if the device is set to a lower output power if such function is available.

Disposal of Electric and Electronic Equipment

(Applicable in the EU and other European countries with separate collection systems)
This equipment contains electric and/or electronic parts and must therefore not be disposed of as normal household waste. Instead, it should be disposed at the respective collection points for recycling provided by the communities. For you, this is free of charge. If the equipment contains exchangeable (rechargeable) batteries, these too must be removed before and, if necessary, in turn be disposed of according to the relevant regulations (see also the respective comments in this unit's instructions). Further information about the subject is available at your community administration, your local waste collection company, or in the store where you purchased this equipment. This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

©2023 Bushnell Outdoor Products
Bushnell, ™, ®, denote trademarks of Bushnell Outdoor Products
www.bushnell.com
9200 Cody, Overland Park, KS 66214 Made in China
http://bushnellgolf.com/patents

Scan the code to download the Bushnell Golf Mobile app and register your Tour V6 Laser Rangefinder.
Android and Google Play are registered trademarks of Google Inc. in the United States and other countries. iPhone and Apple Store are trademarks of Apple Inc., registered in the U.S. and other countries. Other names may be trademarks of their respective owners.