Intended Use - DeWalt DWH205DH-CA Instruction Manual

• Do not use without dustbox and/or filter in place.
• Do not use the appliance to pick up flammable or
combustible liquids, such as gasoline, or use in areas
where flammable or combustible liquids are present.
Do not pick up anything that is burning or smoking,
•
such as cigarettes, matches or hot ashes.
• To avoid spontaneous combustion, empty dust box
after each use.
• Do not leave dust extractor unattended when
battery is installed. Remove battery pack when not in
use and before servicing.
Do not put any objects into the openings. Do not use
•
with any opening blocked; keep free of dust, lint, hair and
anything else that may reduce air flow.

WARNING: Use of this tool can generate and/
or disburse dust, which may cause serious and
permanent respiratory or other injury. Although the
filter material removes 99.97% of airborne particles
0.3 microns or greater, the dust extration system
may not capture all of the dust created by the drilling
operation. Always use NIOSH/OSHA approved
respiratory protection appropriate for the dust
exposure. Direct particles away from face and body.

WARNING: Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19)
during use. Under some conditions and duration
of use, noise from this product may contribute to
hearing loss.

CAUTION: When not in use, place tool on its side
on a stable surface where it will not cause a
tripping or falling hazard. Some tools with large
battery packs will stand upright on the battery pack
but may be easily knocked over.
• Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be
caught in moving parts.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.

Intended Use

Your dust extraction system DWH205 has been designed
for the extraction of dust in professional hammerdrilling in
masonry or concrete, and with solid drill bits mounted to
the power tool. DO nOT use for drilling plastic, wood or
metal. DO nOT use with hollow bits or core bits.
This dust extraction system will fit the DCH263 D
Max. cordless SDS PLUS hammer.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
The dust extraction system is an attachment for use with
professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Max drilling depth
Max drill bit length
Max drilling diameter
Small diameter head
Standard diameter head
Stop bit head
Worklight (Fig. A)

CAUTION: Do not stare into worklight. Serious eye
injury could result.
There is a worklight
extractor. The worklight is activated when the trigger switch
is depressed, and will automatically turn off 20 seconds after
the trigger switch is released. If the trigger switch remains
depressed, the worklight will remain on.
nOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and before making any
adjustments or removing/installing attachments
or accessories. An accidental start-up can
cause injury.
Attaching and Removing the Dust
Extraction System
WALT 20V
To Attach the Dust Extraction System
e
(Fig. B–D)

WARNING: To reduce the risk of personal injury,
ALWAYS operate the tool with the side handle
properly installed and securely tightened. Failure
to do so may result in the side handle slipping during
SPECIFICATIONS
8" (203 mm) usable, 10" (254 mm) overall
10" (254 mm)
1" (25 mm)
The small diameter head can be used
with bit diameters 5/32" (4 mm) to 1/2"
(13 mm) and up to 10" (254 mm) overall
length (8" [203 mm] useable).
NOTE: This head is intended for use
only with small bits that meet the
above specifications.
The standard diameter head can be used
with bit diameters 1/2" (13 mm) to 1"
(25 mm) and up to 10" (254 mm) overall
length (8" [203 mm] useable).
NOTE: This head is intended for use
only with standard bits that meet the
above specifications.
The stop bit head can be used with
bit diameters up to a 1-1/2" (38 mm)
wide shoulder.
NOTE: This head is intended for use
only with stop bits that meet the
above specifications.
located on the top of the dust
9
English
3