Page 1
SUN2000 (8KTL-28KTL) User Manual Issue Date 2019-06-30 HUAWEI TECHNOLOGIES CO., LTD.
Page 2
Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS"...
Page 5
Technical Specifications. Issue 04 (2013-11-25) Added description about the SUN2000-23KTL. Issue 03 (2013-10-11) Added descriptions about the SUN2000-28KTL. Issue 02 (2013-06-08) This issue is the second official release. Issue 01 (2013-04-26) This issue is the first official release. Issue 12 (2019-06-30)
Installation Ensure that DC and AC power supplies are disconnected before operations. Read this document before installation. Huawei shall not be liable for any consequence caused by violation of the regulations specified in this document. Shield the PV modules with opaque cloth before connecting cables to the SUN2000.
Page 12
A model in the range from SUN2000-8KTL to SUN2000-23KTL can connect to the low-voltage power grid directly without connecting to a transformer. Power Grid Modes for the SUN2000 All SUN2000 models except the SUN2000-28KTL support the power grid modes TN-S, TN-C, TN-C-S, and TT, as shown in Figure 2-3.
N cable and a PE cable, 400 V), a transformer is required to convert the 480 V voltage to the 400 V voltage. Figure 2-3 Power grid modes supported by all SUN2000 models except the SUN2000-28KTL Figure 2-4 Power grid mode supported by the SUN2000-28KTL 2.2 Appearance...
Page 19
The power flow from the SUN2000 to the power grid and the voltage and current of each output. − All models except the SUN2000-28KTL display the effective phase voltage and current of the SUN2000 three-phase output. − The SUN2000-28KTL displays the effective line voltage and current.
Page 22
SUN2000 (8KTL-28KTL) User Manual 2 Overview Figure 2-12 Circuit diagram for the SUN2000-28KTL Each component of the SUN2000 works as follows: The input current check circuit determines the operating status of each PV string and generates an alarm prompting for repair if a PV string is not working properly.
Page 51
Strip the insulation layer of each core wire by 12 mm. Figure 5-6 Stripped length The preceding figure shows the stripped length only for all SUN2000 models except the SUN2000-28KTL. For the SUN2000-28KTL, align the neutral cable with the protective jacket and cut off the neutral cable. Issue 12 (2019-06-30)
Page 53
Connect N to hole number 4. For the SUN2000-28KTL, do not connect the neutral wire to hole number 4. Figure 5-10 Connecting an AC output cable to the coupler Step 5 Check that all core wires are properly connected, as shown in Figure 5-11.
Page 57
PV strings. Therefore, two to four DC inputs should be evenly distributed on two terminal groups. The SUN2000-15KTL to SUN2000-28KTL provide three MPPT routes to track the maximum power point for PV strings. Therefore, two to six DC inputs should be evenly distributed on three terminal groups.
Page 71
Advanced User, and choose Settings > Wizard to set the grid code. The SUN2000-28KTL applies only to the medium-voltage grid connection scenarios, and supports only the Chinese, German, and customized medium-voltage grid codes.
NOTE As the SUN2000-28KTL has three-phase, three-wire outputs, the output voltage and current are the line voltage and line current. The preceding screen is displayed on all models except the SUN2000-28KTL.
Page 137
IEC low-voltage power grid (60 Hz) Custom (50Hz) Reserved Custom (60Hz) Reserved Medium-voltage power grid codes apply to SUN2000 models including the SUN2000-28KTL. Table B-2 describes the countries to which medium-voltage power grid codes apply. Table B-2 Medium-voltage power grid codes Power Grid Code...