Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Huawei SUN2000-2KTL-L0
Summary of Contents for Huawei SUN2000-2KTL-L0
- Page 1 SUN2000-(2KTL-5KTL)-L0 Quick Guide Issue: 01 Part Number: 31509986 Date: 2018-09-05 HUAWEI TECHNOLOGIES CO., LTD.
-
Page 2: Packing List
4. Before installing the device, check that the package contents are intact and complete against the packing list. If any damage is found or any component is missing, contact your dealer. 5. Huawei shall not be liable for any device damage caused by the violation of instructions in this document. -
Page 3: Installing The Device
Overview (2) Front panel (1) LED (3) Mounting bracket (4) Mounting plate (5) Heat sink (6) Ventilation valve (7) DC switch (DC SWITCH) (8) DC input terminals (9) DC input terminals (PV1+/PV1–) (PV2+/PV2–) (10) COM port (COM) (11) USB-4G port cover (USB-4G) (12) AC output port (AC) (13) Antenna port (ANT) (14) Ground point... -
Page 4: Installing The Mounting Bracket
Dimensions If multiple inverters need to be installed, see SUN2000-(2KTL-5KTL)-L0 User Manual for the installation dimensions. Installing the Mounting Bracket Wall-mounted Installation DANGER Avoid drilling holes in the utility pipes and/or cables attached to the back of the wall. -
Page 5: Installing The Sun2000
Support-mounted Installation Prepare M8 stainless bolt assemblies (including flat washers, spring washers, and M8 bolts) with appropriate lengths as well as matched flat washers and nuts based on the support specifications. You are advised to apply anti-rust paint on the hole positions for protection. Installing the SUN2000 ... -
Page 6: Optional) Installing The 4G Module
(Optional) Installing the 4G Module The USB-4G port is available only for a 4G module, rather than a USB data cable. Install the SIM card in the direction shown by the silk screen and arrow on the slot. Press the SIM card until it snaps into place and locked, which means that the SIM card is ... -
Page 7: Optional) Installing The Wifi Antenna
(Optional) Installing the WiFi Antenna The 4G module and WiFi antenna cannot be used at the same time. Antenna port (ANT) Ensure that the WiFi antenna is installed securely. Connecting Cables Preparing Cables Prepare cables based on site requirements. Conductor Cross- Outer No. -
Page 8: Installing The Pe Cable
Installing the PE Cable DANGER Do not connect the neutral wire to the enclosure as a PE cable. Otherwise, electric shocks will be caused. Ground point Recommended: Apply silica gel or paint around a ground terminal after connecting the ground cable. - Page 9 Two-Core Cable (L and N) Click 2. Connect the AC connector to the AC output port, and then Check the route of the AC output power cable. AC output port (AC)
-
Page 10: Installing The Dc Input Power Cable
Plug insert To remove the AC connector, follow the steps of its installation in reverse order. Then remove the plug insert as shown in the right figure. Installing the DC Input Power Cable 1. Ensure that the PV string is well insulated to ground. 2. - Page 11 using metal stamping forming contacts Positive connector Positive metal terminal Negative Click connector Negative metal terminal Pull the DC input power Ensure that the cable will cable back to ensure that not be extracted after it is connected securely. crimped. Ensure that the cables are Ensure that the locking correctly connected.
- Page 12 (Optional) Installing the RS485 Communications Cable When laying out communications cables, separate them from power cables to avoid strong signal interference sources. Ensure that the exposed core wire is totally inserted into the cable hole and connected securely. ...
-
Page 13: Verifying The Installation
Click Verifying the Installation Acceptance Criteria The SUN2000 is installed correctly and securely. The WiFi antenna or 4G module is installed correctly and securely. Cables are routed properly as required by the customer. Cable ties are secured evenly and no burr exists. The ground cable is connected correctly and securely. -
Page 14: Powering On The System
Powering On the System Before turning on the AC switch between the SUN2000 and the power grid, check whether the AC voltage is within the specified range. After turning on the AC switch, turn on the DC switch within 1 minute. Otherwise, the SUN2000 will start to export power to the power grid. - Page 15 Type Status (Blinking at Long Intervals: On for Meaning 1s and then Off for 1s; Blinking at Short Intervals: On for 0.2s and then Off for 0.2s) Running LED1 LED2 indication Steady green Steady green The SUN2000 is exporting power to the power grid. Blinking green at The DC is on and the AC is off.
-
Page 16: Customer Service Contact Information
Customer Service Contact Information Customer Service Contact Information Region Country Hotline Email France Germany Spain Europe Italy eu_inverter_support@huawei.com 0080033888888 United Kingdom Netherlands Others Australia au_inverter_support@huawei.com 1800046639 Turkey tr_inverter_support@huawei.com 0080021686868 Malaysia /1800220036 (+66) 26542662 apsupport@huawei.com Asia Pacific (Local Call) Thailand 1800290055 (Toll-free... - Page 17 Huawei Technologies Co., Ltd. Huawei Industrial Base, Bantian, Longgang Shenzhen 518129 People's Republic of China solar.huawei.com...