1. Manuals
  2. Brands
  3. Escea Manuals
  4. Indoor Fireplace
  5. DS Series
  6. Installation instructions manual

Escea DS Series Installation Instructions Manual

Double sided conversion kit
Hide thumbs Also See for DS Series:
Table of Contents

Advertisement

Quick Links

Download this manual

Accessory Installation Instruction

DS Series Double Sided Conversion Kit

1. On the front of the fire, remove the glass retaining bracket (shown below in grey) by unscrewing the 1/4 turn fasteners
located at the top of the glass. The DS1150, DS1400, and DS1650 will have 4 fasteners (shown below); the DS1900 will
have 6 1/4 turn fasteners. Remove the glass.
2. Remove the bottom trim (shaded in grey below). If necessary, insert a large slotted screwdriver into the lance forms and
twist.
3. Remove the infill screws: the DS1150 and DS1400 have four (shown below); the DS1650 and the DS1900 have eight.
Lift one end of the infill up into the top corner of the firebox and then out towards you, taking care not to scratch the
firebox paint and reflective panels. Remove the outer burners by sliding them away from the centre of the fireplace,
followed by the centre burner, which slides out to the left.
4. On the inside of the firebox, slightly loosen (do not remove) the firebox liner bracket (shaded in the diagram below) by
loosening—not removing—the screws (circled in the diagram below). The DS1150 and DS1400 have 3 screws (shown
below); the DS1650 will have 4 screws and the DS1900 will have 6 screws.
630391_7

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DS Series and is the answer not in the manual?

Questions and answers

Related Manuals for Escea DS Series

Summary of Contents for Escea DS Series

  • Page 1 Accessory Installation Instruction DS Series Double Sided Conversion Kit 1. On the front of the fire, remove the glass retaining bracket (shown below in grey) by unscrewing the 1/4 turn fasteners located at the top of the glass. The DS1150, DS1400, and DS1650 will have 4 fasteners (shown below); the DS1900 will have 6 1/4 turn fasteners.
  • Page 2 Accessory Installation Instruction DS Series Double Sided Conversion Kit 5. Carefully swing the lower edge of each firebox liner towards you and pull down to release each panel (shaded in the diagram below). It may be necessary to slide the firebox liner to the side prior to swinging it out. Remove the firebox liner bracket (loosened in step 4) and then replace the screws (loosened in step 4).
  • Page 3 Accessory Installation Instruction DS Series Double Sided Conversion Kit Remove the screws from the back panel (circled below) and remove the back panel of the appliance. Once the back panel is removed, reattach the four screws from the gib board fixing bracket.
  • Page 4 Accessory Installation Instruction DS Series Double Sided Conversion Kit Bend tab Bend tab Push tab in down at new down to to the next perforated horizontal perforated mark and position section secure Open Close Remove the screw Replace P lease Take...
  • Page 5 Accessory Installation Instruction DS Series Double Sided Conversion Kit 9. Remove the bottom air deflector (shown shaded below). Inserted a large slotted screwdriver into the slot and twist it to release the air deflector. 10. Unscrew the 1/4 turn fasteners. The DS1150, DS1400, and DS1650 will have 4 fasteners (circled below); the DS1900 will have 6 1/4 turn fasteners.
  • Page 6 Accessory Installation Instruction DS Series Double Sided Conversion Kit 12. Reinstall the burners and the infill by reversing the steps followed in step 3. Next, fit the two side trims. These are fixed top and bottom with the low profile black self tapper screws (see below).

This manual is also suitable for:

Ds1150Ds1400Ds1650Ds1900

Table of Contents