For U.S.A. only: • To locate the closest authorized dealer in your area, please call 1-800-449-8989. Operating Instructions With Installation Manual (for qualified service personnel) Electronic Board Model No. The unit in this picture is UB-2815C. UB-2815C UB-2315C...
Page 2
Thank you for purchasing the Panasonic Electronic Board. For optimum performance and safety, please read these instructions carefully. • Markers (Black, Red, Blue) ..1 each • Eraser ..... . 1 •...
Page 3
Federal Communications Commission Requirements Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
For Your Safety For Your Safety To prevent severe injury and loss of life, read this section carefully before using the unit to ensure proper and safe operation of your unit. CLASS 1 LED PRODUCT The following graphic symbols are used in this Operating Instructions manual.
Stop operation immediately if your unit emits smoke, excessive heat, abnormal smell or unusual noise. These conditions can cause fire or electric shock. Immediately turn the unit off and unplug the power cord, and contact your dealer for service. When disconnecting the unit, grasp the plug instead of the cord.
Page 8
For Your Safety CAUTION Power When the unit is not used over an extended period of time, switch it Off and unplug it. If an unused unit is left connected to a power source for a long period, degraded insulation may cause electric shock, current leakage or fire.
A replacement fuse cover can be purchased from your local Panasonic Dealer. If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and disposed of safely.
• Use a shielded USB cable that is certified as logo by USB-IF. • Do not connect two or more Panasonic electronic boards to a computer. It may cause the computer operation to become unstable. Approx. 20 mm ( Approx.
Page 11
Battery If battery is used improperly, battery may leak, causing corrosion to the unit, or it may burst. To prevent this, always follow the precautions given below. • Always insert battery with its polarity properly oriented. • If the battery has run out, remove it immediately and dispose of it according to local regulations. Leaving drained battery may result in leakage.
Caster Control Panel Power Cord Battery Holder AC Inlet * This is a diagram of the UB-2815C. UB-2315C is equipped with one board stopper and one board stopper lever. Board Stopper Board Stopper Lever Caster with Lock Fall-prevention Extension Leg...
Control Panel Display Name When in standby mode, the display shows the current status of the unit as follows: • The time is shown on the top left corner of the display. • The scanning mode is shown on the icons on the left side of the display. •...
PDF/TIFF format • Images output to a USB flash memory device or an SD memory card are saved as follows: [Folder] For UB-2815C: “UB-2815C” For UB-2315C: “UB-2315C” [File name] MMDDHHxx.pdf (in the case of PDF file) Sequential number (00-99) Hour...
Storing images on a USB flash memory device Set the power switch to on ( I ). • The scanner will move to the home position and stop. Connect the USB flash memory device to “USB Connector-A for USB Flash Memory Device”.
SD memory card specifications using the appropriate formatting software. You can also download the formatting software for the SD memory card from the following site: http://panasonic.co.jp/pavc/global/cs/sd/ download/sd_formatter.html Press the Mode Key mode. to select the scanning Press the Start/Stop Key.
Printing with an external printer Set the power switch to on ( I ). • The scanner will move to the home position and stop. Turn the external printer on and load the paper. Connect the external printer to “USB Connector-A for Printer”...
Note • Be careful not to strike people or objects when rotating the whiteboard. • The UB-2315C is equipped with one board stopper and one board stopper lever. Move the scanner to the left side. Unlock the whiteboard by pushing the board stopper levers down.
Setting the Unit The following settings can be made using the control panel. Setting for scanning time display It is possible to select whether the time that an image is scanned is displayed on the image. Panaboard [On] Press the Set-up Key •...
Press the Set-up Key • The set-up screen is displayed. For UB-2815C, press the Set-up Key ( 3 times. For UB-2315C, press the Set-up Key ( twice. • Time set-up is selected. Press the Multi-Copy Key ( • The time set-up screen is displayed.
Press the Set-up Key • The set-up screen is displayed. For UB-2815C, press the Set-up Key ( 4 times. For UB-2315C, press the Set-up Key ( 3 times. • The Test Print feature is selected. Press the Multi-Copy Key ( •...
(refer to “Installing Drivers / Panaboard Software”). • If you connect the unit to a USB hub, it is not guaranteed to work. • Do not connect two or more Panasonic electronic boards to a computer. It may cause the computer operation to become unstable.
CD-ROM from “My Computer”. When “Welcome” window appears, click [Next]. Click [Panaboard Setup]. • To install Panasonic-DMS, click [Panasonic- DMS] (see page 25). • To read the operating instructions in the provided CD-ROM, the Adobe Reader or Acrobat Reader must be installed in your computer.
Page 24
Computer Interfacing When the following window appears after files are copied, power the unit on, and connect the USB cable to your computer. Follow the on-screen instructions if the wizard windows appear. • If the wizard window is displayed to connect to the Windows Update in Windows XP SP2, select [No].
AGREEMENT” carefully, choose “I accept the terms of the license agreement.”, and click [Next]. Follow the on-screen instructions when messages appear. When the setup process is completed, restart Windows. • About Panasonic-DMS, refer to the Document Management System operating instructions in the CD-ROM.
Follows the instructions on the screen. After uninstalling, restart your computer. Removing the Panasonic- DMS Software If you need to remove Panasonic-DMS, perform the following steps. Power on your computer and start Windows. • Log on as an administrator for Windows 2000 or Windows XP.
Scanning with the Panasonic- By using Panasonic-DMS, it is possible to scan handwritten text/diagrams or attached documents. Click [Start] and select Programs– Panasonic–Panasonic Document Management System–Document Manager. (For Windows XP, All Programs is displayed instead of Programs.) Click the File menu, then click Select Source...
Computer Interfacing Panaboard Operation Panel Mode Button Configuration Button Name Mode Button Start Button Configuration Button Help Button Close Button Help Button Description Click to select the scanning mode. Color-Fine: For scanning in high-resolution color. Recommended for scanning color documents. Color-Standard: For scanning in normal-resolution color.
Daily Care and Maintenance Always turn off the power switch and unplug the power plug when cleaning outside and inside the unit. Cleaning the Whiteboard and the Unit Gently wipe the whiteboard and unit with a water- dampened cloth that has been thoroughly wrung. Note •...
Daily Care and Maintenance Cleaning the White Balance Area If white lines appear or the image is completely blank, clean the white balance area. Panaboard Move the scanner to the center of the white- board. Gently wipe both sides of the white balance area with a water-dampened cloth that has been thoroughly wrung.
Replacing the Battery for the unit clock When the clock battery has been drained, the time set- up screen is displayed each time the unit’s power is turned on. Replace the battery as follows and set the current time (see page 20). Loosen the screw attached to the lower side of the Control Panel 1, then remove the battery holder 2.
For information regarding available USB flash memory devices, SD memory cards, and printers, refer to the following site: http://panasonic.co.jp/pcc/products/en/eboard/ ub-2815c_info.htm The USB flash memory device or printer is connected via a USB hub. Do not connect via a USB hub.
Page 33
Issue Printed images are thin or blank. When the scanned image is printed, colors are shifted or blurred. When the unit’s power is turned on, the time set-up screen is displayed. The computer does not recognize this unit. The USB driver does not work properly.
U307014 images on the USB flash memory U307160 device are set to “read only”: U407035 for UB-2815C: “UB-2815C” for UB-2315C: “UB-2315C” The following folders for storing U306014 images on the SD memory card are U306160 set to “read only”: U406035 for UB-2815C: “UB-2815C”...
Page 35
Check Scanner attachment. Transfer the image files in the following folder on the USB flash memory device or SD memory card to another location. for UB-2815C: “UB-2815C” for UB-2315C: “UB-2315C” Troubleshooting Remedy Page – – – –...
Dry erase felt-tipped markers (black, red and blue) 7 mm ( ") or less Color-Fine / Color-Standard / B/W-Normal / B/W-Dark Standard-size / Full-size UB-2315C 1,858 mm × 1,534 mm × 1,207 mm " × 5' " × 3' 11 (6' 1 "...
Page 37
Full Speed USB 2.0 FAT (FAT16) format (Maximum capacity: 2 GB) Refer to the Internet home page* Color scanning: PDF/JPEG B/W scanning: PDF/TIFF Specifications UB-2315C [A4] Color-Fine: 2.4 x 2.4 dot/mm (62 x 62 dpi) Color-Standard: 2.4 x 1.2 dot/mm...
B/W scanning: PDF/TIFF KX-B031 (set of 10 black markers), KX-B032 (set of 10 red markers), KX-B033 (set of 10 blue markers) KX-B042 (set of 6 erasers) KX-B035 (contains one black, one red, and one blue markers and one eraser) UB-2315C...
For Your Safety To prevent severe injury and loss of life, read this section carefully before using the unit to ensure proper and safe operation of your unit. The following graphic symbols are used in this Installation Manual. WARNING CAUTION This symbol is used to alert operators to a specific operating procedure that must...
Assembling the unit ■ Accessories for assembling The package includes the parts for setting up the unit shown below. Make sure that all of these parts are included in the package before proceeding. Part Name Power cord Connector cover Screw Washer Hexagonal wrench Illustration...
Scanner Shipping box * This is a diagram of the UB-2815C. UB-2315C is equipped with one board stopper and one board stopper lever. Caution • The shipping box, cushioning material, and other packing material will be necessary for repackaging this unit.
Page 43
Remove the accessory box, two stands and four cushions (upper). Note • Be careful not to damage the whiteboard. Remove the two transportation plates. Remove the two screws using the hexagonal wrench, and remove the transportation plate. In the same way, remove the other side transportation plate.
Page 44
Attach the stands to the unit. Each stand has four holes (A, B, C, D). 1) Attach the stand to the unit with the locking caster up. 2) When attaching the unit to the stand at normal height (1,858 mm [6' 1 screws with washers using the hexagonal wrench through holes A and C.
Attach the scanner to the unit. 1) Take the scanner out. 2) Align the shaft of the scanner with the slot of the slider and push the shaft in the direction of the arrow 1 shown in the figure allowing the narrow part of the shaft to fit in the slot.
Electronic Board Operations Check After assembling the unit, perform the procedures presented in the following table to make sure it functions properly. Step Turn the power switch on. Set the time. (Refer to “Setting the current time” on page 20.) Connect a USB flash memory device or SD memory card.
Cushions Electronic board Scanner Shipping box * This is a diagram of the UB-2815C. UB-2315C is equipped with one board stopper and one board stopper lever. Joints Joints [Contents of Accessory box] • Markers (Black, Red, Blue) ....1 each •...