Muse M-189 P, M-189 PMR - Projection Clock Radio Manual

Muse M-189 P, M-189 PMR - Projection Clock Radio Manual

Advertisement

Muse M-189 P, M-189 PMR - Projection Clock Radio Manual

LOCATION AND DESCRIPTION OF CONTROLS

Overview - Part 1Overview - Part 2Overview - Part 3

  1. Clock LED display
  2. Power ON indicator
  3. Sleep indicator
  4. Nap indicator
  5. SNOOZE indicator
  6. Alarm 1 indicator (wake up to buzzer)
  7. Alarm 1 indicator (wake up to radio)
  8. Alarm 2 indicator (wake up to buzzer)
  9. Alarm 2 indicator (wake up to radio)
  10. Volume control
  11. Alarm 1 LED display
  12. Alarm 2 LED display
  13. Tuning / Set knob
  14. Time projector
  15. P.1 button (To preset channel 1 station)
  16. P.2 button (To preset channel 2 station)
  17. P.3 button (To preset channel 3 station)
  18. ROTATE: To rotate the projected time.
  19. Nap
    To fall asleep with the radio
  20. /SOURCE: To turn unit on/off; To select function mode: FM, AUX
  21. Setting the clock
  22. Alarm 1 button
  23. Alarm 2 button
  24. PROJECTION: Projector on/off
  25. DIMMER: Dimmer light intensity of the screen
    SNOOZE: Interval alarm repetition
  26. USB port for charging
  27. AUX IN jack (3.5mm)
  28. FM wire antenna
  29. AC power cord
  30. Battery compartment
  31. Speaker

Read the instructions carefully before operating the unit.

POWER SUPPLY

AC: 100-240V 50/60Hz

DC: 2x1.5V, battery type AAA/R03/UM4 (not provided) for back-up
For optimal performance, alkaline batteries are recommended.

These batteries must be replaced every six months.

  1. Insert the plug of power cord into a standard wall outlet.
  2. Install the batteries in their compartment. Use only the size and type of batteries specified. Respect the polarity indicated in the compartment. Improper polarity can cause damage to the device. In order to avoid leakage, remove the batteries when unit will not be used for a long period of time. Do not mix different types of batteries or old batteries with new ones.


Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

BACKUP SYSTEM

All settings are memorized, however, the clock time could occasionally need to be readjusted. In case of power failure, if backup batteries are not installed, the screen will flash to indicate this power failure and the necessity to redo your settings.

TURNING UNIT ON/OFF

In standby mode, press once to turn on the unit. The ON indicator will light up. Press and hold for 2 seconds to turn off the unit. The ON indicator will turn off.

SELECTING FUNCTION

When the unit is ON, press SOURCE button repeatedly to select the desired function in cycle: FM, AUX.

LISTENING TO THE RADIO

When the unit is ON, press SOURCE button repeatedly to select FM mode. The display will show current frequency for a few seconds and change to clock time.

  1. Use the TUNING control to select the desired station.
  2. Adjust the volume to desired level.
  3. To stop listening to the radio, press and hold for 2 seconds to turn off the unit.

To enhance radio reception ability:
FM: Extend the antenna.

Preset stations

This unit can store 3 FM stations.

Manual storage

  1. Use the TUNING control to select the desired station.
  2. Press and hold P.1 button until you hear a beep sound from the unit. "P 01" appears on display for a few seconds. The station is saved as preset channel 1.
  • Same procedure applies for P.2 and P.3 buttons to store other stations.

Listen to station presets

Short press P.1, P.2 or P.3 respectively to select your preset station.

Automatic Tuning

In FM mode, fast rotate TUNING knob clockwise or anti-clockwise. The radio will automatically search a station upward or downward and stop at a strong station.

SETTING THE TIME

  1. In standby mode, press and hold button to enter time setting mode and the hour digits flash.
  2. Rotate SET knob to adjust the hour value. Press to confirm and minute digits flash.
  3. Rotate SET knob to adjust the minute value and press again to confirm.

NOTE:
If during the adjustment time no key is activated in 5 seconds, the current display will be automatically stored.

SETTING THE ALARM AND THE ALARM MODE

  1. In standby mode, press ALM.1 button repeatedly to select the source of wake up: Buzzer or FM. The Alarm 1 LED display and the corresponding alarm indicator light up.
  2. Press and hold ALM.1 for a few seconds. The hour digits flash.
  3. Rotate SET knob to adjust the hour value. Press ALM.1 to confirm and minute digits flash.
  4. Rotate SET knob to adjust the minute value and press ALM.1 again to confirm.
  • Same procedure applies for Alarm 2 with ALM.2 button.

Note:

  • The corresponding alarm indicator blinks when the alarm function is activated.
  • The previous level of listening is stored, the volume of the alarm will be identical. If you wake up with the radio, do not forget to check the volume level.

STOPPING THE ALARM

  1. Alarm repetition
    Press SNOOZE. The alarm stops and will sound again 9 minutes later. The snooze indicator lights up during the snooze time.

  2. Alarm stop
    Press or ALM.1. The alarm will sound again the next day at the same time.

  3. Alarm Cancellation
    In standby mode, press ALM.1 repeatedly until the Alarm 1 LED display lights off.

  • Same procedure applies for Alarm 2 with ALM.2 button.

SLEEP FUNCTION

In sleep mode, the unit will turn off automatically after a specified time. You can select duration in minutes before the unit turns off automatically.

  1. When the unit is on, press to select 120-90-60-45-30-15 or 5 minutes of listening. The Indicator lights up. The unit will automatically turn off after the specified time.
  2. To cancel the sleep function, repeatedly press button until "OFF" is displayed.

Note:

  1. Sleep time can only be set when the unit is turned ON.
  2. Press button to check the remaining sleep time.

NAP FUNCTION

This function wakes you up after a short period of time. Only the buzzer may be selected.

  1. In standby mode, press to select 120-90-60-45-30-15 or 5 minutes for your nap. The indicator lights up.
  2. To stop the alarm, press or . .
  3. To cancel the function, press repeatedly until "OFF" is displayed.

CONNECTING AUXILIARY SOURCE

  1. Connect your auxiliary source (e.g. mp3 player) to the AUX IN jack on the back of unit (cable not included).
  2. When the unit is on, press SOURCE button on unit repeatedly to select AUX mode. The display will show "" for a few seconds and change to clock time.
  3. Start playback from your auxiliary source.
  4. Adjust the volume to desired level.
  5. To stop playback, disconnect your auxiliary source from the AUX IN jack.

DIMMER

Press DIMMER to select the brightness of the screen: high, low or off.

TIME PROJECTION

  1. Turn on or off the projector with the PROJECTION button.
  2. Project the time on a light / flat surface such as the ceiling.
  3. If necessary, you many rotate the image of the projected time 180º with the ROTATE button, so it display properly.

USB CHARGING

This unit is equipped with a built-in USB charging port (Output: DC 5V 1A ) for recharging your mobile device (e.g. Smartphone, tablet, etc. )

Simply plug the USB charging cable (not included) into the USB charging port and connect it to your mobile device.

TECHNICAL SPECIFICATIONS

POWER SUPPLY: AC 100-240V 50/60Hz, 12W consumption

DC 2x1.5V, battery type AAA/R03/UM-4 (not provided) for back-up

RADIO: FM 87.5-108MHz

Note:
Design and specification are subject to change without notice.

MORE INFORMATION


To reduce the risk of electric shock, do not open the device, there is no party inside for the user. Refer all servicing to qualified personnel.

shock hazard
The lightning with the arrow symbol in the triangle is a warning sign alerting the user to "dangerous voltage" inside the unit.

warning
The exclamation point in the triangle is a warning sign alerting the user of important instructions accompanying the product.

The Caution mark is located at the back of the device.

  • The use of apparatus in moderate climates.
  • The Marking plate is located at the bottom of the device.
  • Make sure to have a minimum distance of 5 cm around the unit for sufficient ventilation.
  • Ensure that the ventilation openings is not covered with items such as newspapers, tablecloths, curtains, etc.
  • Do not place naked flame sources, such as lighted candles on the apparatus.
  • Do not expose this appliance to dripping or splashing water.
  • Do not place objects filled with liquids, such as glass, vase on the device.
  • Do not throw batteries into fire! Respect the environment when disposing of used batteries.
  • Batteries should not be exposed to excessive heat such as sunshine, fire or other similar heat source.
  • The power plug is used as a disconnect device and must be easily accessible. To be completely disconnected from the power, the plug of the appliance should be disconnected completely. The socket must not be obstructed and should be easily accessible during intended use.
  • Under the influence of fast transient and / or electrostatic electric phenomenon, the product may malfunction and the user must perform a power reset of the device.


If in the future, you need to get rid of this product, please note that Waste electrical products should not be disposed of with household waste. Recycling facilities exist. Check with your municipality or ask your dealer for advice. (Directive for Waste Electrical and Electronic Equipment)

NEW ONE S.A.S 10, Rue de la Mission, 25480 Ecole Valentin, France

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Muse M-189 P, M-189 PMR - Projection Clock Radio Manual

Advertisement

Need help?

Need help?

Do you have a question about the M-189 P and is the answer not in the manual?

Questions and answers

Table of Contents