Teka HI-735, HI-735 ME - Oven Quick Start Guide

Also See for HI-735:

Features list (5 pages)

Table of Contents

Contents

1 Overview
2 Control Panel
3 Use of the Oven
4 Tray Handle
5 Technical Information
6 Documents / Resources
- 6.1 Download manual

Teka HI-735, HI-735 ME - Oven Quick Start Guide

Overview

Overview
HI-735/HI-735 ME

Control Panel with anti finger-mark varnish
Oven Seal
Fold-down Grill element
Catalytic Side Panel (**)
Grid
Telescopic Guides (**)
Cake Tray (*)
Roasting Tray (*)
Door switch
Hinge
Door
Air Outlet
Fixing to Unit
Grill Screen
Smoke Outlet
Light
Catalytic Rear Panel
Tray Handle
Fan
Large Interior Glass Door

(*) Inside oven and trays with easy cleaning enamel.
(**) Depending on the model.

Control Panel

Control Panel - Model HI-735 Model HI-735

Control Panel - Model HI-735 ME Model HI-735 ME

Electronic timer.
Oven pilot light.
Function selector.
Heating indicator light. Indicates that heat is being passed to the food and it goes out when the set temperature is reached.
Temperature selector.
Hob pilot. It indicates that one of the hob burners is on.
Control knobs for the hob.

Switch off oven

Conventional
It is used for sponges and cakes where the heat received must be uniform to achieve a spongy texture.

Conventional with fan
Appropriate for roasts and cakes. The fan spreads the heat uniformly inside the oven.

Grill
For preparing dishes with superficial roasting. It allows the outer layer to be browned without affecting the inside of the food. Ideal for flat food, such as steaks, ribs, fish, toast.

MaxiGrill
Allows greater surfaces to be prepared, than with the grill, together with higher power reducing the time required for browning of the food.

MaxiGrill with fan
Allows uniform roasting at the same time as surface browning. Ideal for grills. Special for large volume pieces, such as poultry, game etc. It is recommended to put the item on a rack with a tray beneath to collect the stock and juices.

While using the Grill, MaxiGrill or MaxiGrill with fan, the door must be kept closed.

Turbo
The fan distributes the heat produced by an element located at the rear of the oven. Due to the uniform heat distribution, it allows roasting and baking to take place at two heights at the same time.
This cooking mode allows defrosting of food. To do this, set the temperature selector to position.

Lower element
Heats only from beneath. Suitable for heating dishes and raising pastry and similar.

Lower element with fan
It distributes the heat from the lower part of the oven and is ideal for cakes with jam or fruit filling, which only require heating from beneath. Pre-heating is always necessary.

Grill and Lower element
Special for roasts. It can be used for any piece, whatever its size.

Note
The pilot light remains on in any cooking function.

Use of the Oven

Setting the time on the clock

On connecting the oven, you will notice that 12:00 appears on the clock and that a light begins to flash above the symbol. Pressing the "+" and "-" buttons the correct time can be set on the clock, which is subsequently stored and the flashing light goes out.

Manual use

After setting the correct time, the oven is ready for use. Select a temperature and a cooking function.

To switch off the oven, set the controls to the position .

Functions of the Electronic Clock Programmer

Warning function:
This function generates a warning tone at a specified time.

Cooking time:
This function allows to programme the oven to cook for a specified time, after which it will switch itself off.

End of cooking time:
This function allows to establish the exact hour, after which the oven will switch itself off.

Duration and automatic stop:
This function is used to control the duration and the time at which the oven will turn itself off. This function allows the oven to start and stop automatically.

Clock light:
The clock light can be switched off when the oven is not in use.

Warning function

Press the MODE button until the signal above the symbol begins to flash.
Choose the time when you want the alarm to sound, pressing the "+" or "-" buttons.
Subsequently, the light will remain on indicating that the alarm is programmed.
At the end of the programmed time, an alarm will sound and the light will begin to flash.
Press any button to turn off the alarm and the screen shows the current time again.

Programming the cooking time

Press the MODE button until the indicator above the symbol begins to flash.
Select the length of time, pressing the "+" or "-" buttons.
Subsequently, the indicator that was flashing will light, indicating that the oven will switch itself off automatically.
The clock will then show the current time.
Select a temperature and cooking function.
When the set time has elapsed, the oven will disconnect, an alarm will sound and the indicator will begin to flash.
Press any button to switch off the alarm, reconnecting the oven.
Set the controls in the position to switch off the oven.

Programming the end of cooking time for the oven

Press the MODE button until the indicator above the symbol begins to flash.
Select the time that cooking is to finish, pressing the "+" or "-" buttons.
Subsequently, the indicator that was flashing is lit, indicating that the oven will switch itself off automatically.
The clock will then show the current time.
Select a temperature and a cooking function.
When the programmed time is reached, the oven will disconnect, an alarm will sound and the indicator will begin to flash.
Press any button to switch off the alarm and the oven will reconnect.
Set the controls to the position to switch off the oven.

This function may be used even though you are already cooking in your oven. To do so, follow the instructions given except Nº 5.

Programming the duration and automatic stop

Press the MODE button until the indicator above the symbol begins to flash.
Select the length of cooking time pressing the "+" or "-" buttons.
Subsequently, the indicator that was flashing will remain lit.
Press the mode button until the indicator above the symbol begins to flash.
Select the time that cooking should finish pressing the "+" or "-" buttons.
Subsequently, the indicator that was flashing will remain lit.
Select a function and cooking temperature.
The oven will remain disconnected with the indicators above the and symbols lit. Your oven is programmed.
When the time to begin cooking is reached, the oven will switch itself on and will continue cooking during the programmed time.
When the programmed finishing time is reached, the oven will disconnect, an alarm will sound and the light above the symbol will begin to flash.
Press any button to switch off the alarm and the oven will reconnect.
Set the controls to the position to switch of the oven.

Pressing the MODE button the display on the screen shows any function p rogrammed. It can be changed by pressing the "+" or "-" buttons. On selecting the desired function, the indicator above the corresponding signal will light.
In the event of a power cut, all the programming of the electronic clock will be erased. The correct time has to be reset and the watch reprogrammed.

Switching off the clock light

To switch off the clock light, press two buttons at the same time and, after several seconds the screen of your clock will go out. To re-light the clock, press any button and the current time will reappear.
This function can only be used when the clock shows the current time and there is no function programmed (No function symbol is lit).
Switching off the clock light

Tray Handle

The tray handle is used when you need to move the tray to check the cook. See figures. To handle the tray out the oven, you need to use gloves to protect yourselve.

Cake tray handle position. You must put the short hook over the tray.