Table of Contents
Advertisement
Available languages
Available languages
čin je zagotovljeno okolju prijazno in z viri
varčno recikliranje.
Odvisno od prenosa Direktive v nacio-
nalno pravo so vam na voljo naslednje
možnosti:
• odpadno opremo lahko oddate na pro-
dajnem mestu,
• ali na uradnem zbirališču,
• ali jo pošljete nazaj proizvajalcu/osebi,
ki jo je dala na trg.
To ne velja za pribor in pripomočke za
odpadno opremo, če nimajo električnih
sestavnih delov.
Nadomestni deli/pribor
Nadomestne dele in pribor dobite na www.grizzlytools.shop
Če imate težave s postopkom naročanja, uporabite kontaktni obrazec. Pri dodatnih vpra-
šanjih se obrnite na servisno službo (glejte stran 439).
Pol. Naziv ........................................................................... Št. izdelka
11
Omejevalni kabel, 200 m ............................................................92000035
12
Pritrdilni žeblji ............................................................................91106075
13
Kavlji, 350 kosov .......................................................................92000034
14
Napajalnik (EU) .........................................................................80001359
Napajalnik (UK) .........................................................................80001358
17
Polnilna postaja ..........................................................................80001357
20
Noži (Proizvajalčeva oznaka: 183-8B10101) +
34
Vijak noža .................................................................................92000001
Odstranite akumulatorje v skladu z lokal-
nimi predpisi. Okvarjene ali iztrošene aku-
mulatorje je treba v skladu z Direktivo
2006/66/EG reciklirati. Oddajte aku-
mulatorje na zbirnem mestu za odpadne
baterije za okoljsko primerno predelavo. V
zvezi s tem povprašajte svoje lokalno pod-
jetje za odstranjevanje odpadkov ali našo
servisno službo.
Akumulatorje odstranite izpraznjene. Pri-
poročamo, da pole prelepite z lepilnim
trakom za zaščito pred kratkim stikom.
Akumulatorja ne odpirajte.
SI
437
Advertisement
Chapters
Table of Contents
Need help?
Do you have a question about the PMRDA 20-Li A1 and is the answer not in the manual?
Questions and answers
Üdvözlöm Power locked 371 mi a teendö ? Köszönöm4
If the Parkside PMRDA 20-Li A1 power is locked, open the cover and unlock the display using the 4-digit PIN code (default is “1111”).
This answer is automatically generated
Good afternoon I hope you doing good, i have Robot Parkside but i forgot the pasward if you can help me how to reset the password
To reset the password (PIN) for the Parkside Robot PMRDA 20-Li A1, follow these steps:
1. Open the cover if necessary.
2. Unlock the display using the 4-digit PIN (default is "1111").
3. Press the OK button to enter the main menu.
4. Use the arrow buttons to select "Settings" and confirm with OK.
5. Select "Change PIN" and confirm with OK.
6. Enter the old 4-digit PIN. If incorrect, use the back button to retry.
If you forgot the old PIN, the manual does not provide a reset method. You may need to check the manufacturer's support.
This answer is automatically generated
Il tosaerba si blocca come se fosse incastrato
The Parkside PMRDA 20-Li A1 lawn mower may get stuck as if it is jammed due to a blocked cutting motor. This can be caused by foreign objects or faults in the blades. To resolve this issue, check for any obstructions or damage to the blades and remove any debris. If the problem persists, refer to the error troubleshooting section or contact the manufacturer.
This answer is automatically generated
Its showing "loop signal lost" and i have check the cable but its ok
"Loop signal lost" for the Parkside PMRDA 20-Li A1 means the mower is not receiving a signal from the boundary wire. This can happen if the wire is not installed correctly or is damaged.
To fix it:
1. Check the correct installation of the boundary wire.
2. Repair or reinstall the wire if needed.
3. Place the mower inside the boundary area.
4. Restart the mower.
This answer is automatically generated
Why is battery not charging?
The Parkside PMRDA 20-Li A1 battery may not be charging due to the following reasons:
1. Low battery voltage: The battery may not meet the required minimum charge level (70% for automatic mowing, 30% for spot mode).
2. Poor contact between the charging station and the mower: Check for correct contact and restart the device in the charging station.
3. Charging current too low: Check the power supply.
4. No signal from the boundary line: Ensure the boundary line is correctly installed.
5. Mechanical or electrical damage: Do not open the battery or charger; seek professional service.
6. Wet or dirty charger: Keep the charger clean and dry; do not use it outdoors.
This answer is automatically generated
HII cannot restart my mower after the winter break . The battery is charged to 100% but thee lcd screen is unresponsive
The LCD screen of the Parkside PMRDA 20-Li A1 mower may be unresponsive after winter despite a fully charged battery because the display may be locked. Unlocking the display using the 4-digit PIN (factory setting "1111") may be required to access functions and read information.
This answer is automatically generated
Kde najdu tlačítko reset na robotické sekačce smart
The reset function for the Parkside PMRDA 20-Li A1 robotic lawn mower is accessed through the menu, not a physical reset button. To reset to factory settings:
1. Open the cover.
2. Unlock the display using the 4-digit PIN (default is "1111").
3. Press the OK button to enter the main menu.
4. Use the arrow buttons to select "Settings".
5. Select "Factory Settings".
6. Confirm with OK.
The mower will then reset to factory settings.
This answer is automatically generated
I have a narrow path (minimum 20cm) with walls between areas of my lawn will this present a problem?
How to change the PIN?