Advertisement
Ensure the nozzle is aimed correctly at the working surface before switching the machine on.
Before activating the trigger, GRIP the gun firmly to counteract the recoil from the high pressure water jet.
4
WARNING! Avoid sudden bursts of water as such will cause water pressure to drop and put extreme pressure on hoses and connectors.
4
If, during operation, power failure occurs turn the electricity and water off for safety reasons, (See Note ‘c’ at end of Section 4).
p
WARNING! The high pressure jet will cause loose particles to be propelled at high speed, which may cause serious injury.
4
WARNING! DO NOT use the machine without a water supply. Dry running can seriously damage the unit.
p
WARNING! DO NOT leave motor running for more than 1-2 minutes without operating trigger, as temperature/pressure
p
increase may damage sealing system.
p
DO NOT obstruct ventilation grills during operation.
DO NOT stand the washer on its end during use. The washer must only be used when sat horizontally.
8
DO NOT use the washer with flammable or toxic liquids or any other product. Only use recommended detergent. Non-recommended
8
detergents may corrode the machine cover and accessories.
8
DO NOT jam the trigger in the operating position.
DO NOT adjust any internal control valves, as they have been set at the factory.
8
DO NOT leave the washer running unattended.
8
DO NOT connect other appliances to the machine inlet or outlet.
8
DO NOT use in damp or wet weather conditions.
8
DO NOT move the unit by pulling the hoses or electrical cables. Use handle.
8
DO NOT touch plug with wet hands, to avoid the risk of electrocution keep all connections dry and off the ground.
8
DO NOT direct jet against yourself, other persons or animals, electrical equipment or the machine itself.
8
DO NOT use washer if you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT allow children or untrained persons to operate the washer.
8
WARNING! Discharge residual pressure before disconnecting the washer hose. Pressure left in unit may cause injury.
8
After use disconnect washer from electrical mains and water supply and store in a safe, dry, childproof area.
p
4
2.
SPECIFICATION & CONTENT
2.1. SPECIFICATION
Lance . . . . . . .Rotating Nozzle & Direct Jet
Maximum Pressure . . . . . . . . . . . .1520psi
Effective Cleaning Power . . . . . . . .2150psi
Water Flow . . . . . . . . . . . . . . . . . . .430l/h
Motor Power . . . . . . . . . . . . . . . . . .1750W
2.2.
CONTENTS
Unpack the product and check contents against the
are damaged or missing contact your supplier immediately.
DESCRIPTION OF ITEMS
1
Water outlet
2
Water inlet with filter
3
High pressure lance
4
Rotary lance
5
Gun with safety catch
6
Instruction manual
7
Power cord with plug
8
High pressure hose
9
Nozzle cleaning tool
10
Motor ON/OFF switch
11
Detergent bottle with flow control
3.
SET UP
WARNING! Ensure pressure washer is switched off and unplugged from the mains electrical power supply before proceeding.
3.1.
Insert the high pressure hose into the gun handle and push firmly home. Lock the hose by inserting clip (fig 2. A). If clip does not grip,
p
tap it gently home. Slide the anti-kink sleeve up to meet the gun handle.
3.2.
To connect either lance (fig 1 items 3 & 4) to the gun (5) push the lance into the end of the gun and twist to lock as in fig 3.
3.3.
Connect the other end of high pressure hose to the water outlet on the washer (fig 4).
3.4.
Connect the mains water supply hose (not supplied) to the water inlet on the pressure washer (fig 5). DO NOT turn the water on at this
stage. The supply hose must be reinforced, and have an internal diameter of 1/2”. The water supply must be at least equal to the
washer capacity. The water temperature must NOT exceed 140
WARNING! REMINDER: The pressure washer must only be used with clean water. Non-filtered water or corrosive chemicals must not
be used as they will damage the washer.
p
3.5.
Check the washer power ON/OFF switch and ensure it is in the ‘OFF’ position.
3.6.
Having carefully followed the safety instructions in Section 1, plug the washer into the mains power supply. The washer is now ready
for use as described in Section 4.
fig 2.
Input Voltage. . . . . . . . . . . . . . . . . . . 230V
Motor rpm . . . . . . . . . . . . . . . . . . . . . 2800
Max. Inlet Temp . . . . . . . . . . . . . . . . . 50
Hose Length . . . . . . . . . . . . . . . . . . . 6.0m
Weight . . . . . . . . . . . . . . . . . . . . . . . 11kg
list
below. Also check that the machine has an identification plate or label. If label or parts
fig 1.
F (50
C). The water supply pressure must NOT exceed 145psi (10 bar).
O
O
fig 3.
By rotating the stream of water at
high speed, it is possible to increase
the effective cleaning pressure of
C
washer. We quote the pressure the
O
water leaves the pump at as ‘Manifold
power of washer as the ‘Effective
fig 5.
fig 4.
Pressure’ and express cleaning
Cleaning Power’.
PC2150 - 0023 - (3) - 060899
Advertisement
