Specialized SPEEDZONE II - Bike Computer Manual

INSTALLATION

• Remove the components from the side of the handlebar intended for the installation of the display mount.
• Fig. 1: Install the display mount and rotate into position A .
• Tighten until the mount does not slip easily B . Do not overtighten. Recommended torque is 4.4 in-lbf / 0.5 N.
• To install the display, position sideways C then rotate 90° D .
  

BATTERY REPLACEMENT

• Fig 2: Use a very small flat head screwdriver to lift up the edge of the battery cap, then gently lift the battery out of the cap.
  
  
• Fig 3: Replace the display unit battery with a new CR 2032 coin cell battery, place the new battery into the cap with the text facing inside the cap E . Make sure the seal is not damaged and press the cap back in, making sure the tab of the lid is first aligned with the recess on the display F .
  
  
• When the battery is replaced, all information stored on the display (odometer, timer) is erased. If desired, take note of the information before replacing the battery.
• Fig 3: The sensor uses a 23A battery G . To access the battery, rotate the cap using a coin or flat head screwdriver.

DISPLAY FEATURES

MAIN SCREENS

8. Battery icon turns on (coin cell battery low).
9. No Signal or key for 30 min.
10. Clear function data (hold left button for 2 seconds).
11. Show odometer data (hold right button for 2 seconds).

Wake from shipping mode: After removing the display from the packaging, press and hold the left and right buttons for two (2) seconds to wake up the display for the first time.

LEGEND

	Change mode / value	Press left button quickly
	Change mode / value	Press right button quickly
	Reset function data	Press left button for two (2) seconds
	Show odometer	Press right button for two (2) seconds
	Odometer Setup	Press right button for four (4) seconds
	System Setup	Press left and right buttons for four (4) seconds
	Change setup screen	Press left and right buttons quickly
	Quick-scroll down (setup modes)	Press left button for more than 1 second
	Quick-scroll up (setup modes)	Press right button for more than 1 second

SPEED SENSOR INSTALLATION

12. Adjust the magnet position so the magnet is aligned with the line on the bottom of the edge of the sensor.
    Position with 1/32 - 1/8 in (1-3mm) of separation. DO NOT overtighten the magnet.
13. The sensor should be mounted with the battery door cap toward the ground, with no more than 24" (in) /600mm distance between the sensor and the handlebar.
    

DEFAULT PAGE SETTINGS/NAVIGATION

• There are 4 preset pages, each of which displays a different combination of information.
• The pages can be navigated using the left / right buttons.

14. To clear the Distance, Average speed, Timer and Max speed data, press the left button for two (2) seconds.

SYSTEM SETUP

• Choose the desired time O (12 or 24 hour), hour P and minute Q .
• Set the units R (km/h or mph).
• Set the wheel S and tire T size (preset or custom).
• If your wheel/tire size is not listed or you want to guarantee the closest accuracy, measure your wheel circumference U (one full rotation of a wheel, using the valve stem V as a marker).
  

GENERAL INFO

CLEANING / CARE:

• Do not expose the display to intense heat or sunlight for a prolonged period of time. This can damage the display and/or battery.
• Only use a damp or dry soft cloth to clean the display. Do not use harsh cleaning products.
• Do not disassemble or drop the display.
• Make sure the display and mount are firmly installed on the handlebar before riding.

SYSTEM SETUP (custom tire size)

• When selecting the custom (CUST) W option from the wheel diameter options, Data Field 2 will flash. Enter the tire circumference size in millimeters. To scroll quickly, press and hold the left button to scroll down or the right button to scroll up.
  

ISED Canada Statement: This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-3(B)/NMB-3(B).
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 millimeters between the radiator and your body.

FUNCTION OPTIONS / SPECIFICATIONS

ODOMETER SETUP

• After replacing the battery, the odometer can be set manually X , separately from the system setup.
• Press the right button for four (4) seconds, set the first digit, then press the left and right buttons together to move to the next digit and set it. Repeat for all four digits until the odometer is set.
  

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Specialized SPEEDZONE II - Bike Computer Manual