Advertisement
6.3.2
one complete turn of the handle is equal to approx 2mm as
indicated on the scale next to the feed port.
It is better to use a cutting depth of between 0.5 and 1.5 mm
(1/64"~1/16") for best results. trying to remove excessive amounts
on a single pass will result in motor overload and dull the blades.
6.3.3
Introduce the workpiece from the feed (left-hand) side. Gently
guide the workpiece through the sM1314. Do not force the
workpiece but allow the machine to do the work.
NOtE: When thicknessing it is recommended to keep the feed table clean
and free of sap. Apply a small amount of penetration spray and wipe
over with a cloth.
WARNiNG! Do not remove chips or dust from the table while the
machine is running, always disconnect from the mains supply
before attempting any kind of maintenance. Do not attempt to
thickness short pieces of wood.
7. MAiNtENANcE
WARNiNG! Prior to doing any maintenance work, always disconnect
from the mains. Any protective guards which have been removed
must be mounted again after the maintenance work.
7.1
BELt tENsiON
7.1.1
After the first 5 hours of operation check the belt tension.
7.1.2
remove the front outer plastic cover by removing three Allen bolts.
7.1.3
check tension by pushing against the belt. the play should be
about 15-20mm.
7.1.4
If loose, slacken the four motor mount bolts and adjust the height
of the motor until the correct belt tension is achieved (fig.10).
tighten the motor bolts and re-check the belt tension.
replace belt cover.
WARNiNG! never run the sM1314 without the covers fitted.
7.2
GENERAL MAiNtENANcE
7.2.1
regularly clean thicknessing table and oil threaded spindles for the
height adjustment of the thicknessing table.
7.2.2
regularly clean the sM1314 drive gear, using a brush or
compressed air to remove dust. Lubricate all bearing points, gears,
chain wheels and chains with a few drops of engine oil. Keep flat
bell and wheel free of grease (fig.11 & 12).
7.2.3
the table surface should always be kept free of resin.
7.2.4
In order to prevent the motor from overheating, regularly check that
no dust has accumulated on the ventilation apertures of the motor.
After a prolonged period of operation, users are recommended to
have the machine checked by an authorised service agent.
7.3
tOOL cARE
the cutter head, clamping devices, blade supports and blades used
on the machine must be kept free from resin build up as a clean tool
improves the cutting quality. this can be done by soaking the blade
supports and blades for 24 hours in paraffin, white spirit or
commercially available resin remover.
7.4
REPLAciNG BLADEs
WARNiNG! Disconnect from power before servicing!
7.4.1
unplug the planer from power source.
7.4.2
Loosen the four blade lock screws. (fig.13)
7.4.3
Lift blade and blade clamp from cutterhead.
NOtE: Do not lose the two small blade support springs mounted in the
cutter block under the blade.
7.4.4
clean any sawdust and resin build up from cutterhead and blade
clamp.
7.4.5
Place blade clamp against the replacement blade and replace in
cutterhead.
7.4.6
secure blade and blade clamp using four blade lock screws. Do
not over-tighten.
NOtE: check blade height and alignment.
7.4.7
to check blade alignment, set the table to the (0) position. use a
straight edge i.e metal ruler or set square and position it across
the two tables. the blade should make friction contact with the
ruler, check at either end of the blade and in the middle to ensure
the blade is level. Loosen the blade lock screws and adjust height
accordingly using the blade adjustment grub screws (fig.14).
7.4.8
repeat the procedure to replace the other blades.
7.4.9
Make sure all the blade lock screws are tight, do not overtighten, if
any of the threads are stripped replace immediately.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMPORtANt: no liability is accepted for incorrect use of this product.
WARRANtY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
iNFORMAtiON: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Fig.13
sole Uk Distributor, sealey Group,
Kempson Way, suffolk Business Park,
Bury st. Edmunds, suffolk,
IP32 7Ar
Original Language Version
Fig.9
Fig.10
Fig.11
Fig.12
01284 757500
01284 703534
A
Fig.14
www.sealey.co.uk
Web
sales@sealey.co.uk
email
sM1314
Issue: 2 - 15/10/09
Advertisement
