Related Manuals for IXXAT USB-to-CAN II
Summary of Contents for IXXAT USB-to-CAN II
- Page 1 Manual USB-to-CAN II Intelligent PC/CAN Interface The expert for industrial and automotive communication...
- Page 2 Internet: www.ixxat.com e-Mail: info@ixxat.de e-Mail: sales@ixxat.com Support In case of unsolvable problems with this product or other IXXAT products please contact IXXAT in written form by: Fax: +49 (0)7 51 / 5 61 46-29 e-Mail: support@ixxat.de For customers from the USA/Canada Fax: +1-603-471-0880 e-Mail: techsupport@ixxat.com...
-
Page 3: Table Of Contents
4.2 Accessories ................ 14 4.2.1 CAN bus termination resistor ........... 14 4.2.2 Cable adapter RJ45 to Sub-D9M ..........15 4.3 Notes on EMC ..............15 Declaration of conformity ............16 FCC Compliance ............... 17 Copyright IXXAT Automation GmbH USB-to-CAN II - Manual, V1.5... -
Page 5: Introduction
This manual is intended to familiarize you with your interface, also referred to in the following as USB-to-CAN II. Please read this manual before beginning with the installation. 1.2 Features •... -
Page 6: Support
1.3 Support For more information on our products, FAQ lists and installation tips, please refer to the support section of our website (http://www.ixxat.de), which also contains information on current product versions and available updates. If you have any further questions after studying the information on our website and the manuals, please contact our support department. -
Page 7: Installation
For installation of the CAN driver VCI under Windows, please refer to the VCI installation manual. 2.2 Hardware installation The USB-to-CAN II can be plugged in and unplugged during operation of the PC (hot-plug compatible). It is recommended to install the VCI software before plug- ging in for the first time. -
Page 8: Can Bus Connector For Can 2
3.1.3 CAN bus connector for CAN 2 The USB-to-CAN II has a bus interface according to ISO 11898-2, optionally with LIN interface (only variant automotive). The signals of the bus interface are connected to the 8-pin RJ45 connector (see table 3-2). -
Page 9: Cable Adapter Rj45 To Sub-D9M
3.1.4 Cable adapter RJ45 to Sub-D9M The connection of the cable adapter could be seen in table 3-3. The cable could be ordered at IXXAT with the ordering number 1.04.0074.01000. Picture 3-1: Cable adapter RJ45 to Sub-D9M Pin No. -
Page 10: Displays
Connections and displays 3.2 Displays The USB-to-CAN II has 3 LEDs in the variant industrial and 5 LEDs in the variant automotive. The LEDs show the communication status of the according interface. Picture 3-2: Connectors and LEDs of the variant industrial Picture 3-3 Connectors and LEDs of the variant automotive 3.2.1 USB LED... -
Page 11: Can Leds (Can1 And Can2)
CAN messag- es is still possible Bus Off • The CAN controller is in the „Bus Off“ state. No more CAN communication possible Table 3-5: States of the CAN LEDs Copyright IXXAT Automation GmbH USB-to-CAN II - Manual, V1.5... -
Page 12: Can1 Ls Led (Only Variant Automotive)
IXXAT (ordering number 1.04.0075.03000). 3.4 LIN (only variant automotive) The USB-to-CAN II can be configured as LIN Master according to LIN specification V1.3. A voltage of 12 V DC (voltage range 8-18V DC) has to connected to the CAN socket X6. -
Page 13: Appendix
400 mA Power consumption (standby): typically 4 mA maximum 21 mA Housing material: ABS plastics Dimensions (L x B x H) in mm: 98 x 55 x 20 Weight: approx. 200 g Copyright IXXAT Automation GmbH USB-to-CAN II - Manual, V1.5... -
Page 14: Accessories
CSA/UL 60950-00 Class 3862 10, 3862 90 4.2 Accessories 4.2.1 CAN bus termination resistor IXXAT offers a bus termination resistor as a feed through connector (ordering number 1.04.0075.03000). Picture 4-1: Connections of the CAN bus termination resistor Picture 4-2: CAN bus termination resistor Copyright IXXAT Automation GmbH USB-to-CAN II - Handbook, V1.5... -
Page 15: Cable Adapter Rj45 To Sub-D9M
Picture 4-3: Cable adapter RJ45 to Sub-D9M 4.3 Notes on EMC The PC/CAN-Interface USB-to-CAN II may only be used with a PC that has a CE- symbol. The CAN-bus connected to the interface must have a shielded lead. The shield braiding must be connected with low impedance to the connector hous- ing. -
Page 16: Declaration Of Conformity
Appendix Declaration of conformity IXXAT Automation declares that the product: USB-to-CAN II with the article number: 1.01.0062.11110 1.01.0062.11220 1.01.0066.11220 do comply with the EC directives 2004/108/EC. Applied harmonized standards in particular: EN 55022:2006 + A1:2007 EN 55024:1998 + A1:2001 + A2:2003 22.08.2011, Dipl.-Ing. -
Page 17: Fcc Compliance
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Copyright IXXAT Automation GmbH USB-to-CAN II - Manual, V1.5...
Need help?
Do you have a question about the USB-to-CAN II and is the answer not in the manual?
Questions and answers