Pelican 7060 LED - Flashlight Manual

Before disassembling any part of the 7060 LED flashlight, ensure that the flashlight has not been operating for five (5) minutes. During operation, the LED module can become extremely hot and may cause injury if touched.

Flashlight Operation

The 7060 LED is a high performance flashlight for use by professionals. This flashlight comes equipped with a high output LED pre-focused lamp that emits a strong tight beam of white light. There is no need to focus the 7060 LED.

DO NOT SHINE THIS FLASHLIGHT DIRECTLY INTO ANY PERSON'S EYES: THIS MAY RESULT IN INJURY.

Your 7060 LED battery pack comes to you partially charged and needs to be fully charged prior to use.

Momentary –
Partially depress either switch for momentary operation.

Constant On –
Fully depress either switch (click), to lock in the selected mode.

Mode Selection –
Partially depress either switch within.5 second increments to select one of the four available modes. The sequence is High / Strobe / Medium / Low. Fully depress the switch to lock in a selected mode.

Light Off –
Fully depress either switch (click), to turn off the light from any selected mode.

Attach the Power Cord to the Charger Base

1. Plug the right angle connector from the transformer into the back of the charger base.
2. Push the cord into the channel to allow for flush surface mounting. into the back of the charger base.
3. Attach the power cord to the electrical supply.

NOTE: The charger LED will illuminate red when power is supplied.

Charging

To charge the 7060 LED:
CHARGER
The charger is capable of charging the battery pack in under 5 hours. The LED Charge Lights will indicate where the battery is in the charge cycle as follows:

Solid Red = 7060 Not Connected

Flashing Red Light = 7060 Charging

Solid Green Light = 7060 Fully Charged

There is no need to fully discharge the 7060 LED before charging the battery. Charging can occur whenever required and the 7060 LED can be left indefinitely in the charger housing without fear of over-charging.

To Charge:

1. Turn off the flashlight.
2. Attach (snap into place) the flashlight to the charger base ensuring that the charger base contacts line up with the flashlight contacts. The solid red LED will begin flashing ensuring that the charger base contacts line up with the to confirm connection and the start of the charging process.
3. The flashing red LED will change to sold green once a flashlight contacts. The solid red LED will begin flashing to confirm connection and the start of the charging process. complete charge has been achieved.

NOTE: There is no need to fully discharge the 7060 flashlight prior to charging. The flashlight can be left indefinitely in the charger without fear of over-charging.

Battery Replacement

After approximately 500 full charge/discharge cycles, the LI-ION battery stick will no longer hold a charge and must be replaced. The battery stick is available wherever Pelican flashlights are sold or directly from Pelican Products Customer Service.

To replace the battery stick:

1. Unscrew the tail switch located at the rear of the 7060 LED.
2. Remove the battery stick.
3. Insert the new battery stick following the direction on the battery decal.
4. Replace the tail switch & tighten it all the way down.

NOTE: Please act responsibly when disposing of the LI-ION Battery Stick. This part is recyclable and should not be disposed of in the municipal waste system. Please check with your local waste disposal authority for information.

Battery Care

• Do not over discharge your flashlight in an attempt to reduce a "memory" condition. This practice is unnecessary as modern LI-ION batteries, when used in flashlights such as the 7060 LED are highly unlikely to develop this condition. In addition, deep discharging of the batteries may cause the batteries to vent potentially dangerous gases and electrolytes.

O-ring Maintenance

Check closely for cuts, scratches, or otherwise damaged O-ring or mating lens lip surface. Remove any dirt or foreign matter from O-ring sealing surfaces. Keep threads, O-ring groove and insidelip of lens lubricated with silicone grease. See Warranty information for replacement of O-ring.

Charger Mounting

The 7060 LED Charger Base can be permanently mounted in most positions (except upside-down) in vehicles. Two mounting holes are provided to enable attachment using #10 screws.

The right angle plug must be connected before the charger can be mounted (see above).

Vehicle Installation

The 7060 LED charger can be permanently installed in most vehicles and this operation should be performed by a professional auto technician. The charger should not be installed upside-down since certain conditions may cause the 7060 LED to be ejected from the charger. When installing the charger, ensure that the Direct Wiring Rig is connected to an ignition key-switched line. The high amperage draw of this charger may drain the vehicle's battery if connected directly to the battery.

REPLACEMENT PARTS

CAT. # DESCRIPTION

6057F 110V TRANSFORMER FOR CHARGER

6061F DIRECT WIRING RIG FOR CHARGER

7070 DESK/DASH SMART CHARGER BASE UNIT

8056F 12V PLUG-IN CHARGER CORD FOR CHARGER

7069 REPLACEMENT LI-ION BATTERY PACK

7052 YW TRAFFIC WAND (Yellow)

7052 OR TRAFFIC WAND (Orange)

PELICAN LIMITED LIFETIME GUARANTEE OF EXCELLENCE

Pelican Products, Inc. guarantees its lights for a lifetime against breakage or defects in workmanship. This guarantee does not cover the lamp or batteries.

To make a warranty claim, the purchaser must contact Pelican Products, Inc. at 23215 Early Avenue, Torrance, CA 90505 or csrwarranty@pelican.com, or by calling 1-800-473-5422, extension 5. Any warranty claims shall be made by the purchaser as soon as practicable. The purchaser must obtain a return authorization number from Pelican Customer Service prior to returning any product, and is responsible for paying for all warranty freight costs. If Pelican determines that any returned product is not defective, within the terms of this warranty, the purchaser shall pay Pelican all costs of handling, return freight and repairs at Pelican's prevailing rates.

In Australia: To make a warranty claim, the purchaser must contact Pelican Products Australia, Suite 2.33, West Wing, Platinum Bldg., Erina NSW 2250, Tel: +612 4367 7022.

Lifetime Guarantee does not cover Roto Molded cases, AALG products or fabric portion of backpacks. Refer to www.pelican.com/warranty for full details.

PELICAN PRODUCTS, INC.
23215 Early Avenue • Torrance, California 90505 USA Tel 310.326.4700 • FAX 310.326.3311 www.pelican.com

PELICAN PRODUCTS ULC
10221-184th Street • Edmonton, Alberta T5S 2J4 Canada Tel 780.481.6076 • FAX 780.481.9586 www.pelican.ca

All trademarks are registered and/or unregistered trademarks of Pelican Products, Inc., its subsidiaries and/or affiliates.