Sealey SA314.V4 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction protection
manual
1. SAFETY
WARNING! Ensure health & safety, local authority, and general workshop practice regulations are adhered to when using this
‰
equipment.
Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the riveter.
9
WARNING! Disconnect the riveter from the air supply before changing accessories, servicing or performing any maintenance.
‰
Maintain the riveter in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
9
Keep the riveter clean for best and safest performance.
9
WARNING! Always wear approved eye (or face) and hand protection when operating the riveter.
‰
Maintain correct balance and footing. DO NOT over reach, ensure the floor is not slippery, wear non slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/ or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear or working parts.
9
Keep the riveter away from your body and at a safe distance from others.
9
Keep children and unauthorised persons away from the working area.
9
Secure non stable work piece with a clamp, vice or other adequate holding device.
9
Ensure that spent rivet stems are disposed of correctly and DO NOT cause a hazard.
9
WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 90psi.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use, and ensure that all connections are
9
secure.
DO NOT use the riveter for a task it is not designed to perform.
8
DO NOT operate the riveter if any parts are damaged or missing as this may cause failure and/or personal injury.
8
Ensure the safety cap is correctly fitted.
9
DO NOT carry the by the hose, or yank the hose from the air supply.
8
DO NOT get the riveter wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT allow untrained persons to operate the riveter.
8
DO NOT operate the riveter when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT direct air from the air hose at yourself or others.
8
When not in use disconnect from the air supply and store in a safe, dry, child proof location.
9
Avoid unintentional starting.
9
2. INTRODUCTION
i
Suitable for aluminium, steel and stainless steel up to 3/16". Supplied with four riveting nozzles and two spanners. Trigger operated riveter with
hardened jaw assembly and rivet shaft safety cap. Will handle heavy assembly work.
3. SPECIFICATION
Model no: .................................................................... SA314
Nozzle sizes:
.............................. 3/32" (2.4mm), 1/8" 3.2mm, 5/32" (4mm),
.................................................. 3/16" (4.8mm), 1/4" (6.4mm)
Air consumption: ....................................................... 3.46cfm
Operating pressure: ...................................................... 90psi
Air inlet size:..............................................................1/4"BSP
Weight: .......................................................................... 1.6kg
Blind rivet type: .................... aluminium, steel, stainless steel
Noise power/pressure: ......................................... 81/70dB(A)
Vibration: .................................................................. 10.9m/s²
Uncertainty: .............................................................. 4.36m/s²
© Jack Sealey Limited
All manuals and user guides at all-guides.com
AIR RIVETER 1/4" STEEL ALUMINIUM, ALLOY
& STAINLESS STEEL RIVETS
MODEL NO:
Wear ear Wear protective
protection gloves
Original Language Version
SA314.V4
SA314.V4 Issue: 2(H,F) 01/06/18