Sealey SA317 Instructions

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear ear
instructions protection
1. saFety
WarninG! Ensure health & safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
‰
familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the riveter.
9
WarninG! disconnect the riveter from the air supply before changing accessories, servicing or performing any maintenance.
‰
maintain the riveter in good condition (use an authorised service agent).
9
replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
9
Keep the riveter clean for best and safest performance.
9
WarninG! Always wear approved eye (or face) and hand protection when operating the riveter.
‰
maintain correct balance and footing. dO nOt over reach, ensure the floor is not slippery, wear non slip shoes.
9
remove ill fitting clothing. remove ties, watches, rings, and other loose jewellery and contain or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear or working parts.
9
Keep the riveter away from your body and at a safe distance from others.
9
Keep children and unauthorised persons away from the working area.
9
secure non stable work piece with a clamp, vice or other adequate holding device.
9
WarninG! ensure correct air pressure is maintained and not exceeded. recommended pressure 100psi.
‰
Keep air hose away from heat, oil and sharp edges. check air hose for wear before each use, and ensure that all connections are secure.
9
dO nOt use the riveter for a task it is not designed to perform.
8
dO nOt operate the riveter if any parts are damaged or missing as this may cause failure and/or personal injury.
8
dO nOt carry the riveter by the hose, or yank the hose from the air supply.
8
dO nOt get the riveter wet or use in damp/wet locations or areas where there is condensation.
8
dO nOt allow untrained persons to operate the riveter.
8
dO nOt operate the riveter when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
dO nOt direct air from the air hose at yourself or others.
8
When not in use disconnect from the air supply and store in a safe, dry, child proof location.
9
Avoid unintentional starting.
9
2. intrOductiOn
Heavy duty, suitable for all types of nut rivets. supplied with seven mandrels, two spanners and oil syringe. trigger operated with automatic wind
release for fast application. Will handle heavy assembly work.
3. speciFicatiOn
model no: .................................................................... sA317
mandrel size: ........................m3, m4, m5, m6, m8, m10, m12
Air consumption: ......................................................... 4.5cfm
operating pressure: .................................................... 100psi
Air inlet size:..............................................................1/4"BsP
Weight: .......................................................................... 2.6kg
stroke range: .............................................................. 1-8mm
noise power/pressure: ................................ 89dB(A)/78dB(A)
4. air supply
WarninG! ensure the air supply is clean and does not exceed 100psi while operating the riveter. too high an air pressure and unclean
‰
air will cause excessive wear, and may be dangerous, causing damage and/or personal injury.
4.1. ensure the riveter air valve (or trigger) is not depressed before connecting to the air supply.
4.2. You will require an air pressure between 70-100psi.
4.3. drain the compressor daily. Water in the air line will damage the riveter and invalidate your warranty.
4.4. clean air inlet filter weekly. recommended hook-up procedure is shown in fig.1.
4.5. line pressure should be increased to compensate for unusually long air hoses (over 8 metres).
4.6. the minimum hose diameter should be 1/4" i.d., fittings must have the same inside dimensions.
4.7. Keep hose away from heat, oil and sharp edges. check hoses for wear, and make certain that all connections are secure.
© Jack sealey limited
instructions for
air/hydraulic nut riveter heavy-duty
vacuum system
model no:
Wear eye Wear
protection protective
gloves
Original Language Version
sa317
sA317 | issue 1 05/12/16