Wall Mounting - DeWalt DCW682 Instruction Manual

a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out the
lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.

Wall Mounting

Some D WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Introduction
Examine Figure A and your biscuit joiner for a few minutes
to become familiar with the various features and the names
used to describe them. The following sections will discuss
the various controls and you will need to know where
they are.
Paddle Switch (Fig. A)

CAUTION: Hold the auxiliary handle and body of the
tool firmly to maintain control of the tool at start up
and during use and until the blade stops rotating.
Make sure the blade has come to a complete stop
be fore laying the tool down.

CAUTION: Before connecting the tool to a power
source depress and release the paddle switch
to ensure that the switch is off. Depress and release the
paddle switch as described above after any interruption
in power supply to the tool.
nOTE: A biscuit joiner can be placed against the workpiece
before starting. It should be allowed to come up to speed
before plunging. Allow the tool to stop rotating before
putting it down.
1. To turn the tool on, push the lock‑off lever
back of the tool, then depress the paddle switch
tool will run while the switch is depressed.
2. Turn the tool off by releasing the paddle switch.
No‑Volt
The No‑volt function stops the biscuit joiner from restarting
without the switch being cycled if there is a break in the
power supply.
Blade Replacement (Fig. A, G)

WARNING: To reduce the risk of injury, turn unit
off and disconnect it from power source before
installing and removing accessories, before adjusting
or when making repairs. An accidental start‑up can
cause injury.

WARNING: Handle blades carefully. They are
extremely sharp.
nOTE: The DCW682 is shipped with a 4" (102 mm) diameter
blade installed. The blade used MUsT be 4" in diameter and
1/8" in thickness.
In time your saw blade will wear out and need replacement.
To remove the blade, follow the steps below.
1. Turn off and remove the battery.
2. Loosen the 4 torx head screws
the shoe, using the T20 torx screwdriver provided.
3. Rotate the shoe out of the way.
4. Use the spanner wrench provided to loosen
(counterclockwise) the blade nut. Depress the spindle
lock
10
while you unscrew the nut.
5. Remove the blade and have it sharpened or replace it
with a new one.
6. Reinstall the blade by reversing the steps above. Be sure
blade teeth point counterclockwise as shown in Figure G.
7. iMPORTAnT: Always check the fine depth adjustment
when sharpening or replacing the blade. Adjust if
necessary. (Refer to The Controls).
The Controls
The heart of your biscuit joiner is the base/fence assembly.
All of the controls that let you make a variety of precision cuts
are located on this assembly. Take a few minutes to become
familiar with the various controls.
ALWAYS TURN OFF THE BISCUIT JOINER AND REMOVE THE
BATTERY BEFORE MAKING ANY ADJUSTMENTS.
Adjustable Fence (Fig. H, I)
a. The adjustable fence
reference surface to determine the point at which
1 ) once
the slots for the biscuits will be cut. Its adjustable
height feature allows you to position biscuit slots
as close as 3/16" (4.76 mm) and as distant as 1‑3/8"
(35 mm) measured from the workpiece surface to the
14
on the top of the gear case to hold the spindle
6 provides a sturdy, precise
English
toward the
2
. The
1
from the bottom of
15