Page 2
Exif Ver. 2.3, MPF Baseline) Total number of dots: 2 359 296 dots Model No. WW328274 視野率 き製造されています。 DC 8.4 V 、 0.4 A compliant, RAW (Sony ARW 2.3 format) 100% 動画記録方式 ( MP4 方式) Frame coverage: 100% 動作温度 Movie (XAVC S format): MPEG-4 倍率...
Page 3
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO- CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM- NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT サービス,点検時には次のことにご注意ください。...
Page 4
1. SERVICE NOTE – ENGLISH – 1-1. PRECAUTION ON REPLACING THE SY-1039 BOARD 1-2. NOTES FOR REPLACING THE EVF DISPLAY DEVICE (LCD902) OR THE SY-1039 BOARD Destination Data Adjustment values of each EVF display device (LCD902) are stored on the SY board. Therefore, when the LCD902 or the SY board has been replaced, write adjustment values.
Page 5
– ENGLISH – – JAPANESE – 1-3. CHECKING THE Wi-Fi FUNCTION 1-1. SY-1039基板交換時の注意 Perform the following procedure to check the Wi-Fi function. 仕向けデータ 補修用基板と交換する時,補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。 Required equipment: Windows personal computer with Wi-Fi interface Adjust StationからAdjust Manualを起動させて 「DESTINATION DATA WRITE」 を実行させてください。 1. Turn on the power of the unit. USBシリアルNo.およびプロダクトIDについて...
Page 7
2. REPAIR PARTS LIST IDENTIFYING PARTS (ENGLISH) The components identified by mark 0 or dotted line with mark 0 are critical for safety. Follow the disassembly in the numerical order given. Replace only with part number specified. NOTE: Les composants identifiés par une marque 0 sont •...
Page 8
– ENGLISH – – JAPANESE – OPERATION NOTES 作業時の注意 Make sure that the conductive side of a flexible board does not have any stain or foreign materials. フレキシブル基板の導電面に汚れやごみなどがないことを確認してください。 Do not touch the conductive side of flexible boards with bare hands. フレキシブル基板の導電面を素手で触れないようにしてください。...
Page 9
2-1. EXPLODED VIEWS DISASSEMBLY 2-1-1. REAR SECTION-1 1. Remove in numerical order ( ) in the left figure. to #112 X 1 #2 X 4 Back View Back View #112 Open the Jack Lid (5-1) → #2 X 6 → Open the LCD (5-2) → #1 X 3 Right View Left View Bottom View...
Page 10
2-1-2. REAR SECTION-2 DISASSEMBLY 1. Remove in numerical order ( ) in the left figure. #2 X 1 → #12 X 1 → #2 X 3 Right View Back View Bottom View Main Board Section (See page 2-5) Disconnect the flexible board (5-1) → #12 X 1 → #2 X 1 Back View Bottom View Slide and Pull...
Page 11
2-1-3. MAIN BOARD SECTION DISASSEMBLY ns: not supplied 1. Remove in numerical order ( ) in the left figure. 2. The meaning of the symbol in left figure is as follows. Be careful when you remove it. ◇: Solder Remove the flexible board (2) → #2 X 2 #11 X 3 →...
Page 12
2-1-4. OVERALL SECTION DISASSEMBLY ns: not supplied 1. Remove in numerical order ( ) in the left figure. to When removing and re-assembling, pull this connector vertically from the board. #2 X 3 → #11 X 1 Back View Top View ANT901 (Claws) Battery Block Section...
Page 13
2-1-5. IMAGER BLOCK SECTION DISASSEMBLY ns: not supplied 1. Remove in numerical order ( ) in the left figure. Note 5: Do not reuse these Parts because their adhesive force de- #267 X 3 #238 X 3 #197 X 1 creases when they are removed once.
Page 14
2-1-6. IMAGER UNIT SECTION Screw ns: not supplied #238: M1.7 X 3.5 (Black) 4-287-436-01 (All mounted parts and IS-1012 complete board are not supplied, but they are included in Device Service (3200).) #238 #238 Ref. No. Part No. Description 4-484-406-01 IM PLATE (3000), GLASS RETAINER A-2058-109-A INDIVIDUAL, GLASS ASSY (3200)
Page 15
2-1-7. MOUNT SECTION Screw ns: not supplied #198: M1.7 X 4.0 #238: M1.7 X 3.5 (Silver) (Black) 4-186-545-01 4-287-436-01 (Note 2) Note Hold the MB N Contact Unit at MB N Contact Unitの両側の Note 1: Note 1: the center of both sides. 中央部を持ってください。...
Page 16
2-1-8. LCD SECTION Screw ns: not supplied #239: M1.4 X 1.4 #140: M1.7X 2.0 (Black) (Red) 4-287-435-11 2-635-562-01 (Note) Note #140 Note: Refer to “Assembly-7: Notes on Assembling the LCD Note: “Assembly-7: Notes on Assembling the LCD block”を参照し block”. てください。 LCD901 #239 #140...
Page 17
2-1-9. TOP SECTION DISASSEMBLY ns: not supplied 1. Remove in numerical order ( ) in the left figure. 2. The meaning of the symbol in left figure is as follows. Be careful when you remove it. ◇: Solder #2 X 3 #1 X 1 →...
Page 18
2-1-10. BATTERY BLOCK SECTION DISASSEMBLY ns: not supplied 1. The meaning of the symbol in left figure is as follows. Be careful when you remove it. ◇: Solder Screw #1: M1.7 X 2.5 (Black) 2-635-562-11 Ref. No. Part No. Description Ref.
Page 20
3. ASSEMBLY 3-1. ASSEMBLY Assembly-1: Screw tightening sequence when assembling the Assembly-3: Method of attachment of the Mask MB Sheet Assembly-5: Screw tightening sequence when assembling the 2 Install the RL-1018 flexible board to the control switch IM heatsink (3200) (456) MB N Plate (A (3200)) block (RL77900) as shown in the figure.
Page 21
Assembly-7: Notes on Assembling the LCD block Don't make slack LC-1014 flexible Black part of the board flexible board Edge of the hole 1.0mm within Edge of the LC flexible (776) cap 1.0mm within Black part of the flexible board ILCE-7S_L2...
Page 22
3-2. CLEANING PROCEDURE OF OLPF <Cleaning Procedure for the OLPF> 1. Clean up the tip of CCD cleaning jig. 2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight. <Preparation for Remedy> * Do not slide from right to left or up and down while dabbing. If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Page 24
2. REPAIR PARTS LIST AN-1001 AN-1003 BT-2008 CN-1025 DL-1001 2-2. ELECTRICAL PARTS LIST (ENGLISH) (JAPANESE) Ref. No. Part No. Description Ref. No. Part No. Description NOTE: 【使用上の注意】 A-1896-175-A AN-1001 BOARD, COMPLETE < IC > • -XX, -X mean standardized parts, so they may have some dif- • ...
Page 27
SY-1039 Ref. No. Part No. Description Ref. No. Part No. Description Ref. No. Part No. Description Ref. No. Part No. Description * FB1409 1-481-250-11 INDUCTOR, FERRITE BEAD (1005) * L2002 1-400-411-21 INDUCTOR 4.7uH * R0208 1-250-545-11 METAL CHIP 120K 1/16W R1609 (Not supplied) METAL CHIP...
Page 28
SY-1039 Ref. No. Part No. Description Ref. No. Part No. Description R6201 1-218-953-11 METAL CHIP 1/16W RB3101 1-234-387-21 RES, NETWORK 330 (1005X4) RB3201 1-234-387-21 RES, NETWORK 330 (1005X4) R6202 1-245-265-11 METAL CHIP 1/16W R6203 1-216-799-11 METAL CHIP 1/10W RB5501 1-234-372-11 RES, NETWORK 100 (1005X4) * R6503...
Page 29
4. BLOCK DIAGRAMS 4-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. LC-1014 LC-1013 BOARD IS-1012 BOARD IS-1014 SY-1039 BOARD (1/2) FLEXIBLE FLEXIBLE CN6102 CN2303 LCD901 BOARD...
Page 30
4-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. ES-1001 FLEXIBLE BOARD SY-1039 BOARD (2/2) AN-1001 BOARD CN6908 SE001 ANT101 J5501 CN101 SDA_EYE_SENS I2C_SDA I2C_SDA WIRELESS LAN WLAN_SDIO_D0 - D3...
Page 31
4-3. POWER BLOCK DIAGRAM (1/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. SY-1039 BOARD (1/3) UNREG D_1.8V, D_1.8V_WLAN D_3.15V, D_3.15V_MSS, A_3.15V_MSS, D_3.15V_MEDIA F0006 POWER (3/3) UNREG_ACC MS_3.15V Q6501 (PAGE 4-5) UNREG_IC_6501_IN...
Page 32
4-4. POWER BLOCK DIAGRAM (2/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. SY-1039 BOARD (2/3) IC0201 DC/DC CONVERTER CAM_5.5V, (2/35) IC6801 IS_5.5V, CAM_5.5V, EVER_3.15V UNREG_SUB AUDIO_5.5V AUDIO_5.5V LEVEL SHIFT VOUT POWER (3/3)
Page 33
4-5. POWER BLOCK DIAGRAM (3/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. SY-1039 BOARD (3/3) CN3211 LCD902 IC0402 Q0403, Q0404 EVF_10V 10V REG DC/DC CONVERTER (3/35) L0401 UNREG UNREG EVF_12V...
Page 34
5. FRAME SCHEMATIC DIAGRAMS LCD901 LC-1013 BOARD (LCD MODULE) ES-1001 FLEXIBLE BOARD DL-1001 FLEXIBLE BOARD 3.0 INCH CN103 COLOR LCD BACKLIGHT CN102 S002 CONTROL SWITCH DEVICE SERVICE (3200) BLOCK RL-1018 (EV77900) IS-1012 BOARD (SIDE A) FLEXIBLE BOARD SHUTTER AN-1003 UNIT IS-1012 BOARD FLEXIBLE (SIDE B)
Page 35
6. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS – ENGLISH – – JAPANESE – THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS 回路図,プリント図共通ノート (In addition to this, the necessary note is printed in each block) (他に必要なノートは各セクションに記載しています) For Schematic Diagrams 回路図ノート...
Page 41
ANT101 WIRELESS LAN ANTENNA SY-1039 (25/35) CN101 J5501 R0504 (PAGE 6-26) EVER_3.0V EVER_3.15V Through the COAXIAL CABLE C102 COM051 C101 1.8p Q0503 RW1A020ZPFU7 D_3.15V R0503 R101 220k Q0503, Q0505 B+ SWITCH Note: DD_ON3 ANT101 is not supplied, Q0505 but this is included in AN-1001 RN1104MFV(TL3S COMPLETE BOARD.
Page 61
EVER_3.15V CAM_SO_2 XCS_EXT_FL IC5802 TC7WH240FK R5802 3.3k CAM_SCK_2 CAM_SI_2 EXT_FLASH_F3 EXT_FLASH_F2 RB5801 100k C5802 0.1u Q5801 RN1902FE REG_GND IC5802, Q5801 EXTERNAL FLASH I/F Note: C5802 is not supplied, but this is included in SY-1039 COMPLETE BOARD (SERVICE). SY-1039 BOARD (26/35) EXTERNAL FLASH I/F XX MARK: NO MOUNT ILCE-7S_L3...
Page 62
LND001 LEDA XEYE_SENSE_OUT SY-1039 SDA_EYE_SENS (33/35) REG_GND CN6908 (PAGE 6-34) SCL_EYE_SENS R5902 SE001 FR_XRESET XDWN_RESET EYEPIECE SENSOR COM591 D5901 RB520SM-30T2R R001 CA_XRESET_OUT_MSS XMSS_RESET C001 R5901 C5903 0.01u REG_GND Note: SE001 is not supplied, but this is included in ES-1001 FLEXIBLE COMPLETE BOARD. Note: C5903 is not supplied, but this is included in SY-1039 COMPLETE BOARD (SERVICE).
Need help?
Do you have a question about the ILCE-7S and is the answer not in the manual?
Questions and answers