Whirlpool BMZH 5900 IN Installing

10200198GB.fm Page 2 Wednesday, November 16, 2005 12:38 PM
INSTALLING THE BUILT-IN /
UNDERCOUNTER COLUMN OVEN
Recommendations
Important: Disconnect the oven from the
mains before carrying out any installation
work or servicing.
• Installation must be carried out by a qualified
technician in accordance with the manufacturer's
instructions and in compliance with local regulations.
• Unpack the oven and make sure that the
appliance has not been damaged during transport
and that the oven door closes properly. If you
are not sure contact the dealer or the
nearest service centre.
• After removing the oven from its packaging,
leave it on the polystyrene base to prevent it
from being damaged.
• When installing the oven it is advisable to wear
protective gloves.
• Do not lift the oven by the door handle. Get hold
of it using the side openings provided.
Preparing the housing unit
• Kitchen units in contact with the oven must be
heat resistant (80 °C min).
• Cut the kitchen unit to fit before installing the
appliance. Carefully remove any shavings or
sawdust that could prevent the appliance from
running properly.
• The dimensions of the oven and unit are shown
in figures 1-2-3.
• To allow for proper ventilation, an opening
should be left at the bottom of the kitchen unit.
Pay attention to the dimensions in the diagram.
When installation has been completed, the
bottom of the oven must be inaccessible.
• When installing, make sure that the sides of the oven
do not touch the adjacent kitchen units (fig. 4-5).
• When installing ovens under the worktop, leave
a minimum clearance of 5 mm between the
upper edge of the oven and the lower edge of the
worktop (fig. 6). In order for the appliance to
operate properly, this clearance must never
be obstructed.
• If the kitchen unit is not securely fixed to the wall,
it must be anchored with standard brackets (G)
(fig. 7) available on the market.
Electrical connection
Regulations require that the appliance be
earthed.
• Connection to the mains must be carried out by a
qualified electrician in accordance with the
manufacturer's instructions and in compliance
with local regulations.
2
All manuals and user guides at all-guides.com
• The installer is responsible for connecting
• The oven power cable must be long enough to
• Observance of safety directives requires that a
• Do not use multiple plug adapters or extension
• After the oven has been installed, the electrical
Connecting the oven to the power
supply
• Make sure that the voltage indicated on the rating
• If the oven does not have a power supply cable
1. Remove the two fastening screws of the
2. Remove the cover to gain access to the terminal
3. Connect the cable to the terminal box, tighten
4. Put the cover back on by inserting the two
Securing the oven
• Lift the oven getting hold of it by the openings on
• Center the oven in the housing unit before
• Make sure that the plastic spacers (if provided)
appliances correctly to the mains and for
observing the safety regulations.
connect the built-in appliance to the mains.
multi pole switch with a minimum contact gap of
3 mm be used for the installation.
leads.
components must be inaccessible.
plate is the same as the mains voltage. The rating
plate is on the front edge of the oven (visible
when the door is open).
proceed as follows:
terminal box cover located on the bottom part
of the oven's rear covering.
box and insert the power cable (see table)
through the opening located on the bottom of
the oven.
the screws as far as they will go and secure it to
the cable fastener.
blades in the slots and fasten it with the two
screws.
Power supply cable table
N° of conductors Type of cable
~
H05 RR-F 3 X 1.5 mm²
1N+
H05 RR-F 3 X 1.5 mm²
~
2+
(Switzerland only)
the sides and insert it into the housing unit, being
careful not to trap the power supply cable (fig. 8).
securing it.
are positioned correctly in the fastening holes.
Then anchor the oven to the housing unit with
the screws provided.