Table of Contents
Advertisement
Passenger Mode
Passenger Mode is designed to add an additional level of protection
when a passenger is on the bike. Passenger Mode will limit the top
speed of your Lectric XP to 10mph. You and your passenger will need
to continue to practice caution on the Lectric XP.
To engage Lectric "Passenger Mode":
1. Press and hold the (-) and
simultaneously for 5 seconds until the screen flashes PAS and
speedometer.
2. Check setting has been activated by riding without passenger and
speed has been limited to 10mph.
To disengage:
1. Turn your Lectric XP OFF and then ON. Or change your P08
setting to 32 or 100 and Passenger Mode will deactivate.
Walk Mode
Electric bicycles are heavier than bicycles. To make walking the
bicycle easier, your Lectric XP is equipped with Walk Mode, which can
be toggled on or off in the settings menu. Walk Mode may be subject
to local regulations. Check your local regulations to determine if
allowed.
To activate:
Hold down the minus (-) button on the display control pad and the
motor will engage at a speed similar to a slow walk.
NOTE: When Walk Mode is active, "Walking" will appear on the display.
ALWAYS keep wheels in contact with the ground when using
Walk Mode.
To deactivate:
Pull either brake lever to disengage Walk Mode OR press and hold the
minus (-) button on the display control pad.
L E CT R I C E B I K E S.C O M | 602.715.0907
buttons on the control pad
35
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the XP 3.0 and is the answer not in the manual?
Questions and answers
How do you turn on the standard headlight and brake light for night riding?
To turn on the standard headlight and brake light on the Lectric XP 3.0 for night riding, first, make sure the bike is powered on by pressing the power button. Once the display is on, hold the "+" button on the handlebar control until the light symbol appears on the display. This indicates that the lights are on. The headlight will provide a forward beam, and the brake light will activate when braking.
This answer is automatically generated
@Jan Hangen Do the keys need to be engaged for the battery to work
how to charge battery
To charge the Lectric eBikes XP 3.0 battery:
1. Plug the charger cable into the battery pack's charging port.
2. Plug the charger power cable into a wall socket using the supplied AC power cord.
3. Ensure the battery is within the permitted charging temperature range.
4. Do not leave the battery unattended while charging.
5. Do not charge the battery for more than 12 hours.
6. When the charger light turns green, disconnect the charger from the battery and then from the wall socket.
7. If the battery was charged while in the bike frame, insert the rubber plug into the charging port to prevent dirt or water from entering.
This answer is automatically generated
Having trouble reconnecting the stem clamp
To reconnect the stem clamp on a Lectric eBikes XP 3.0:
1. Pull the handlebar stem to its upright position.
2. Push the latch in firmly until it locks in position.
3. Pull on the latch to confirm it is locked and the handlebars cannot fold.
This answer is automatically generated
I need a exploded view of the rear breaking system
How to turn on head light
To turn on the headlight on a Lectric eBikes XP 3.0, hold the plus (+) button on the display control pad for about 3 seconds until the light icon appears on the display.
This answer is automatically generated
Didn't receive a manual with my 3.0 long range bike.
You can obtain the owner's manual for the Lectric XP 3.0 eBike online.
This answer is automatically generated
@Larry J Harrison 410 Jackson St. Muscatine, Iowa 52761
@Mr. Anderson
I cannot find the voice associated the video?
How I turn on the voice with the video.
size of rear axle on XP 3.0
ALINE THE FRONT WEAL WITH HANDLE BAR?
To align the front wheel with the handlebars on a Lectric eBikes XP 3.0, follow these steps:
1. Gather the necessary tools: a 5mm Allen socket, a 5mm Allen wrench, and a torque wrench.
2. Locate the two pinch bolts at the bottom of the stem.
3. Use the 5mm Allen wrench to evenly loosen both pinch bolts until the stem is loose enough to adjust.
4. Grip the handlebars and make small adjustments left and right until the display is lined up with the front tire and headlight.
5. Use the front fork to ensure proper alignment between the stem and handlebars.
6. Once aligned, use the 5mm Allen wrench to tighten the pinch bolts.
7. Torque the bolts down to 20 Nm using the torque wrench and 5mm Allen socket.
After completing these steps, the handlebars should be properly aligned, and the eBike is ready to ride.
This answer is automatically generated