Related Manuals for QSC WL2102-w
Summary of Contents for QSC WL2102-w
- Page 1 WideLine-10 Loudspeaker User Manual WL2102-w – Birch plywood enclosure AF2102-LA – Large aluminum array frame TD-000227-00-D *TD-000227-00*...
-
Page 2: Important Safety Precautions And Explanation Of Symbols
IMPORTANT SAFETY PRECAUTIONS AND EXPLANATION OF SYMBOLS Install in accordance with instructions by QSC, LLC instructions and under the supervision of a licensed Professional Engineer. WARNING! Before placing, installing, rigging, or suspending any speaker product, inspect all hardware, suspension, cabinets, transducers, brackets and associated equipment for damage. - Page 3 WL2102-w enclosures are constructed of birch plywood and weigh 83 lb (37.7 kg). The hardware allows for simple vertical splay angle adjustment of 0, 2, 3, 4, 5, 6, 7, 8, 9, and 10° between enclosures.
- Page 4 TRI AMP/BI AMP Switch TRI AMP TRI AMP: Shading network is NOT applied (shading must be provided by upstream signal processing). Connect the full-range input signal to pins 1+ and 1-, connect the shaded (processed) signal to pins 2+ and 2-.
-
Page 5: Input Connections
Input Connections The input connectors are a pair of Neutrik NL8’s wired in parallel. Connections for bi-amp and tri-amp vary (Table 1). The pin designations for the NL8FC cable connector is shown for reference, bottom right. Note! In TRI AMP mode, the MF (UNSHADED) SELECT switch position determines the input connector wiring! Unexpected results may occur if switch positions and wiring are not strictly controlled. - Page 6 Component Weight 4:1 Design Factor 5:1 Design Factor 7:1 Design Factor 10:1 Design Factor WL2102-w 83 lb / 37.7 kg 2500 lb / 1130 kg 2000 lb / 909 kg 1400 lb / 649 kg 1000 lb / 455 kg AF2102-LA 37 lb / 16.8 kg...
- Page 7 Rigging WideLine-10 enclosures use a three-point suspension system. The system consists of front, left/right, captive articulated joints and a single rear link bar. Articulation is in 2° increments using the first location on the link bar. With the use of the second location, 1° degree increments can be obtained starting at 3°.
- Page 8 The AF2102-LA is used for suspending larger arrays. The AF2102-LA may be inverted and used for ground stacking. Use only the QSC supplied 5/16" diameter x 1.25" long ball-lock pins or equivalents from a reputable source on front receiver tubes.
- Page 9 AF2102-LA The link arm is located on the bottom side of the frame assembly. Use this link for attaching the rear of the first enclosure. The frame allows for up or down angle options for use with either stacking or suspending. The 4° “normal” locations on the link system will yield a net 0° vertical inclination. Use 4°...
- Page 10 Dimensions 25.0" (635 mm) 20.75" (527 mm) 10.75" 7.7" (273 mm) (196 mm) 10.1" (257 mm) 20.4" Side (518 mm) 27.5" 26.8" (699 mm) (681 mm) Front Rear...
-
Page 11: Specifications
Frame used for suspending or stacking applications. Frame weight 37 lb/16.8 kg. Software EASE Focus line array modeling software tool available; visit www.qsc.com or contact QSC’s Technical Services for DSP tunings Ball-lock Pins 7" Stainless steel lanyard 5/16" D x 0.75" W, t-handle: p-n HW-000106-00 (Rear link pin) WL2102-w 5"... -
Page 12: Mailing Address
© 2017 QSC, LLC. All rights reserved. QSC, the QSC logo and WideLine are registered trademarks of QSC, LLC in the U.S. Patent and Trademark office and other countries. Speakon and Neutrik are trademarks of Neutrik. All other trademarks are the property of their respective owners. US Pat. 7,177,437. Other patents may apply or be pending.
Need help?
Do you have a question about the WL2102-w and is the answer not in the manual?
Questions and answers