Figures - ABB HT600348 Operation Manual

Operation Manual / 4 Product description / A130-H.. - A140-H

Figures

Figures
Fig. 1: Layout and function of the turbocharger ...... 4
Fig. 2: Compressor wheel cooling ................................ 5
Fig. 3: Warning plate locations .................................... 6
Fig. 4: Locations of the rating plates .......................... 7
Fig. 5: Transportation of the turbocharger .............. 8
Fig. 6: Removing the turbocharger............................. 9
Fig. 7: Loosening the clamping nut............................ 11
Fig. 8: Putting down the turbocharger ..................... 12
Fig. 9: Inserting gaskets into the bracket ................ 13
Fig. 10: Fitting threaded rods onto the bracket ..... 14
Fig. 11: Requirements for threaded rods .................. 14
Fig. 12: Placing the turbocharger on the bracket.... 15
Fig. 13: Preparing the clamping nut for the tighten-
ing procedure ................................................................ 17
Fig. 14: Tightening pressure screws.......................... 18
Fig. 15: Connecting the compressor cooling air in-
take .................................................................................. 19
Fig. 16: Attaching the support .................................... 19
Fig. 17: Oil orifice ........................................................... 21
Fig. 18: Layout and overview of speed measurement
system ............................................................................ 28
Fig. 19: Replacing the speed sensor ......................... 30
Fig. 20: Noise insulation, bellows............................... 32
Fig. 21: Replacing the protective grid....................... 35
Fig. 22: Cleaning the filter silencer............................ 42
Fig. 23: Compressor-end, non-rotating parts......... 44
Fig. 24: Turbine end, non-rotating parts ................. 45
Fig. 25: Soaking the turbine end................................ 48
Fig. 26: Swivel lifting eyes........................................... 60
Fig. 27: Starpoint ring nut VRM.................................. 60
Fig. 28: Weights of assemblies ................................... 61
Fig. 29: Removing the air inlets ................................. 62
Fig. 30: Removing the gas outlet casing ................. 63
Fig. 31: Dismantling the gas outlet flange............... 64
© Copyright 2020 ABB. All rights reserved.
Fig. 32: Removing the gas outlet flange.................... 65
Fig. 33: Removing the compressor casing................ 66
Fig. 34: Dismantling the wall insert............................ 67
Fig. 35: Press off the casing ........................................ 68
Fig. 36: Oil orifice ........................................................... 69
Fig. 37: Removing cartridge group 1 .......................... 69
Fig. 38: Removing cartridge group 2 ......................... 70
Fig. 39: Removing the nozzle ring................................ 71
Fig. 40: Installing the cartridge group on the service
support ............................................................................ 72
Fig. 41: Measuring clearance A and B......................... 73
Fig. 42: Nozzle ring compression PD ......................... 74
Fig. 43: Installing the nozzle ring ................................ 75
Fig. 44: Measuring the end position of the nozzle
ring ................................................................................... 76
Fig. 45: Lifting the cartridge group and rotating it
by 90° ............................................................................... 76
Fig. 46: Installing the cartridge group....................... 77
Fig. 47: Fitting the wall insert and the diffuser ....... 78
Fig. 48: Installing the compressor casing................. 79
Fig. 49: Measuring clearances N and R...................... 80
Fig. 50: Installing the air inlets.................................... 81
Fig. 51: Installing the gas outlet flange ..................... 82
Fig. 52: Installing the gas outlet casing .................... 82
Fig. 53: Tightening torques ........................................ 83
Fig. 54: Overview of part numbers............................. 90
HZTL4030_EN Revision F February 2020