Sealey AP556CSHV Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instruction
manual
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this product.
‰
Always load evenly with the centre of gravity of the load as near centre as possible.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
Keep the product clean and tidy in accordance with good workshop practice.
9
Use the wheel locks to prevent from inadvertently moving.
9
Keep children and unauthorised persons away from the work area.
9
Lock drawers and doors before moving.
9
DO NOT overload.
8
DO NOT use the for any purpose other than that for which it is designed.
8
DO NOT open more than one drawer at a time - unit may become unstable if multiple loaded drawers are open.
8
DO NOT stand on the product, use it as a ladder or allow others to ride on the trolley.
8
DO NOT leave unattended, especially when loaded, unless the wheels are locked, chocked or otherwise secured.
8
DO NOT use on uneven ground and do not run over curbs or steps - use a ramp.
8
DO NOT use if any part is significantly damaged, paying particular attention to the wheels.
8
NOTE! Lubricate top and bottom channels of drawer slides at least twice a year,
NOTE! The assembly will require assistance.
2. INTRODUCTION
i
Constructed from heavy gauged steel with steel inner walls for extra strength and durability. Heavy-duty 45mm ball-bearing drawer slides
provide superior performance and carry heavier loads. Fitted with Ø125mm castors with black chrome hubcaps, two swivel locking castors and
two fixed. Rollcab design features two lockable side cabinets with pegboard and storage tray in each. Also supplied with 6mm EVA top mat
and 2mm EVA drawer liners in each drawer. In-built storage for a three drawer utility toolbox seat with 30mm cushion. The utility seat has two
locking castors and two swivel. Both have a rust and solvent resistant tough industrial powder coat paint finish. Supplied with two keys for main
rollcab and two keys for utility seat.
3. SPECIFICATION
i
Model No: .........................................................AP556CSHV
(W x D x H) Overall size: .........................679 x 461 x 986mm
Small Drawer (x2): ....................................556 x 392 x 68mm
Large Drawer (x1): ..................................556 x 392 x 147mm
Utility Seat Drawer (x3): ............................278 x 348 x 95mm
Side Cabinets (x2): ...................................86 x 430 x 350mm
4. CONTENTS
See table alongside
© Jack Sealey Limited
3 DRAWER ROLLCAB & UTILITY SEAT
AP556CSHV
MODEL NO:
Item Description
1 Bolt M4x30mm
2 Washer
3 Handle
4 Bolt M6x16mm (black)
5 Side handle
6 Bolt M8x20mm
7 5"x2" swivel castor w/brake
8 5"x2" fixed castor
9 Screw M6x12mm
10 Slider
11 Bolt M6x16mm
12 3"x1" swivel castor w/brake
13 3"x1" swivel castor
14 Bolt M8x35mm
15 Washer
16 Bearing
Original Language Version
Quantity Remark
6 For handle
6 For handle
3
6 4 for side handle &
2 for slider
1
16 For 5"x2" castor
2
2
4 For slider
2
16 For 3"x1" castor
2
2
4 For bearing
4 For bearing
4
AP556CSHV Issue 1 17/05/22