Related Manuals for Sanyo SA-93A
Summary of Contents for Sanyo SA-93A
- Page 1 TECHNICAL & SERVICE MANUAL SA–93A FILE NO. WINDOW TYPE AIR CONDITIONER Model No. Product Code No. Destination SA-93A 1 851 006 94 Australia SA– 93A 700509 REFERENCE NO.
- Page 2 IMPORTANT! When Installing Place of Installation Please Read Before Starting • If possible, install the unit in a shady location. If the site This air conditioner meets strict safety and operating is exposed to the sun, you should provide a sun screen standards.
- Page 3 This manual is designed to help service personnel to understand basic functions, operation and possible troubles and their remedies on SANYO window type air conditioners. You can use this manual both as a reference to find specific information about the capacity, construction of the unit, and as a source of information to help you set up and maintain the air conditioner.
-
Page 4: Table Of Contents
Table of Contents Page 1. OPERATING RANGE ..........................1 2. SPECIFICATIONS 2-1. Unit Specifications .......................... 2 2-2. Major Component Specifications ....................3 2-3. Other Component Specifications....................4 3. DIMENSIONAL DATA..........................5 4. REFRIGERANT FLOW DIAGRAM ......................6 5. PERFORMANCE DATA 5-1. -
Page 5: Operating Range
1. OPERATING RANGE Temperature Indoor Air Intake Temp. Outdoor Air Intake Temp. Maximum 32°C D.B. / 23°C W.B. 43°C D.B. Cooling Minimum 19°C D.B. / 14°C W.B. 19°C D.B. -
Page 6: Specifications
2. SPECIFICATIONS 2-1. Unit Specifications Model SA–93A Power Source 240V Single phase 50Hz Voltage rating 240 V Performance Cooling Capacity 2.55 BTU/h 8,700 Air circulation (High) Moisture removal (High) Liters/h Electrical Rating Cooling Available voltage range 216 ~ 264 Running amperes Power input 1,070 Power factor... -
Page 7: Major Component Specifications
2-2. Major Component Specifications Model SA–93A Controller PCB Part No. — Controls — Control circuit fuse — Remote Control Unit — Compressor Type Rotary (Hermetic) Compressor model 2P17C225AND Source 240V Single phase 50Hz Nominal output Compressor oil ... Amount ATMOS M60 or SUNISO 4GDID ... 350 Ω... -
Page 8: Other Component Specifications
2-3. Other Component Specification Model SA–93A Auto Deflector Motor MA062299 Rating AC 200/240V, 50/60Hz, 20mA, 4W, 5.0/6.0 rpm Coil resistance kΩ (at 20°C) 9.92... -
Page 9: Dimensional Data
3. DIMENSIONAL DATA Model SA–93A Slits for ventilation Side view (L) Front view Side view (R) Power code Power code outlet outlet Unit : mm NOTE Dimension with " " mark indicates the maximum allowable wall thickness required for ventilating the unit. -
Page 10: Refrigerant Flow Diagram
4. REFRIGERANT FLOW DIAGRAM Model SA – 93A Compressor Accumulator Capillary tube... -
Page 11: Performance Data
5. PERFORMANCE DATA 5-1. Cooling Capacity Model SA–93A 240V Single Phase 50Hz RATING CAPACITY 2.55 kW AIR FLOW RATE 360 m EVAPORATOR CONDENSER ENT. TEMP. °C OUTDOOR AMBIENT TEMP. °C W.B. D.B. 2.57 2.46 2.35 2.23 2.10 1.93 0.73 0.79 0.84 0.91 1.02... -
Page 12: Electrical Data
6. ELECTRICAL DATA 6-1. Electrical Characteristics Model SA–93A Fan Motor Compressor Complete Unit Performance at 240V Single phase 50Hz Rating Conditions Running Amps. 0.45 Power Input 0.110 0.96 1.07 Full Load Conditions Running Amps. 0.45 Power Input 0.110 1.26 1.37 Rating Conditions : Indoor Air Temperature 27°C D.B. -
Page 13: Electric Wiring Diagram
6-2. Electrical Wiring Diagrams Model SA–93A To avoid electrical shock hazard, be sure to disconnect power before checking, servicing WARNING and/or cleaning any electrical parts. DATA SUBJECT TO CHANGE WITHOUT NOTICE. -
Page 14: Troubleshooting
7. TROUBLESHOOTING 7-1. Check before and after troubleshooting WARNING Hazardous voltage can cause ELECTRIC SHOCK or DEATH. Disconnect power or turn off circuit breaker before you start checking or servicing. 7-1-1. Check power supply. Check that voltage is in specified range (±10% of the rating). Check that power is being supplied. -
Page 15: Air Conditioner Does Not Operate
7-2. Air conditioner does not operate. 7-2-1. Circuit breaker trips (or fuse blows). A. When the circuit breaker is set to ON, it is tripped soon. (Resetting is not possible.) There is a possibility of ground fault. Check insulation resistance. If resistance value is 2MΩ... - Page 16 B. Circuit breaker trips in several minutes after turning the air conditioner on. There is a possibility of short circuit. • Check capacity of circuit breaker. Replace with suitable one (larger capacity). Capacity of circuit breaker is suitable. Measure resistance of fan motor •...
-
Page 17: Some Part Of Air Conditioner Does Not Operate
7-3. Some part of air conditioner does not operate. 7-3-1. Only fan does not run. • Check fan casing Remove foreign foreign matter on Fan cannot matter or repair. inside. be turned. • Check fan rotation. Turn fan gently once or twice by hand. - Page 18 7-3-3. Only compressor does not run. A. Check setting temperature. Is room temperature too low ? Try to lower setting temperature by thermostat knob COOLER. B. Check compressor and electrical parts. • Check compressor motor Overload relay is working. capacitor. •...
-
Page 19: Air Conditioner Operates, But Abnormalities Are Observed
7-4. Air conditioner operates, but abnormalities are observed. 7-4-1. Poor cooling Temperature difference is small. • Measure temperature of suction and Possibility of Charge refrigerant discharge air of air conditioner. gas shortage. gas (R22). Temperature difference between suction and discharge air is large enough (approx. -
Page 20: Checking Electrical Components
8. CHECKING ELECTRICAL COMPONENTS 8-1. Measurement of Insulation Power plug Resistance The insulation is in good condition if the resistance Ground exceeds 2MΩ. Probe 8-1-1. Power Cord and Unit Fig. 1 Insulation tester Clamp the grounding prong of the power plug with a lead NOTE clip of the insulation resistance tester and measure the The shape of the power plug may differ from that of... -
Page 21: Checking Motor Capacitor
8-2. Checking Motor Capacitor Remove the lead wires from the capacitor terminals, and then place a probe on the capacitor terminals as shown in Fig. 4. Observe the deflection of the pointer, setting the Multimeter resistance measuring range of the multimeter to the maximum value. -
Page 22: Disassembly Procedures
9. DISASSEMBLY PROCEDURES Model SA – 93A NOTE These illustrations are based on typical view of a standard model. Consequently, the shape may differ from that of the air conditioner which you are servicing. 9-1. Removing Front Grille Fig. 1 (1) Open the air intake. -
Page 23: Removing Cabinet
9-2. Removing Cabinet (1) Remove screws A and B. (Fig. 5) (2) Remove the front grille. Refer to "9-1. Removing Front Grille" (3) Remove the stopper screw attached to the base pan Screw B of the unit (Fig. 6) (4) While holding top of the cabinet with one hand, Screw A grasp the handle with another hand and pull the unit toward you. -
Page 24: Removing Evaporator
9-4. Removing Evaporator (1) Remove the top plate. (Fig. 11) (2) Remove screws holding evaporator. (Fig. 11) (3) Grasp lower portion of the evaporator with both hands and tilt it slightly and lift it carefully from the drain pan so as not to distort the copper tube. -
Page 25: Removing Condenser
9-6. Removing Condenser (1) Remove the top plate. (Fig. 11) (2) Remove screws holding condenser. (Fig. 13) (3) Grasp lower portion of the condenser with both hands and tilt it slightly and lift it carefully from the base pan so as not to distort the copper tube. Fig. -
Page 26: Appendix
APPENDIX Model SA – 93A Unit Display and Control Panel VENTILATOR lever Close Open WAIT 3 MINUTES BEFORE RESTARTING THERMOSTAT knob OPERATION SELECTOR switch High Fan AUTO DEFLECTOR Low Fan switch Low Cool High Cool... - Page 27 SANYO Electric Co.,Ltd. Osaka, Japan 700509 01/2002 Printed in Japan...