NETGEAR AC750 WiFi Range Extender EX2800 Quick Start Guide

Getting started

1. For initial setup, place your extender in the same room as your router.
   
   

   ---

   
   
   You can move your extender to a new location after the setup.
2. Plug the extender into an electrical outlet.
3. Wait for Power LED to light green.
4. If the Power LED does not light, press the Power button.
5. Connect your extender to your existing WiFi network using one of these methods:
   • Connect with WPS. Wi‑Fi Protected Setup (WPS) lets you join a secure WiFi network without typing the network name and password. Your router must support WPS to use this method. For more information, see Connect with WPS.
     WPS does not support WEP network security or a hidden WiFi network. If your router WiFi network uses WEP security or uses a hidden WiFi network, follow the instructions in Connect with the NETGEAR installation assistant.
   • Connect with the NETGEAR installation assistant. The Nighthawk app guides you through the installation. For more information, see Connect with the NETGEAR installation assistant.

Connect with WPS

1. Press the WPS button on the extender until the WPS LED blinks.
   
2. Within two minutes, press the WPS button on your router.
   
   When the extender connects to the router, the WPS LED on the extender lights solid green and the Router LED lights.
   Note: If the Router LED does not light, try again. If it still does not light, see the instructions in the Connect with the NETGEAR installation assistant section.
3. If your WiFi router supports the 5 GHz band, repeat Steps 1 and 2 to connect the extender to the 5 GHz band.
4. Move your extender to a new location.
   For more information, see Find a good spot for your extender.
5. Connect your WiFi‑enabled devices to the extended network.
   For more information, see Connect your device to the extended network.

Connect with the NETGEAR installation assistant

1. On a computer or mobile device, open the WiFi connection manager and find and connect to the extender network called NETGEAR_EXT.
   When you are connected to the extender, the Device LED lights.
2. Launch a web browser.
3. Visit www.mywifiext.net.
   The NETGEAR installation assistant displays.
4. Follow the prompts to connect your extender to your existing WiFi network.
5. After the setup is complete, move your extender to a new location.
   For more information, see Find a good spot for your extender.
6. Connect your WiFi‑enabled devices to the extended network using the WiFi credentials you specified during the setup.

Find a good spot for your extender

1. Unplug your extender and move it to a new location.
   We recommend that the new location be about halfway between your router and the area with a poor WiFi signal.
   The extender must be within the range of your router WiFi network.
2. Power on your extender.
3. Use the Router LED to find a spot where the extender‑to‑router connection is optimal.
   For more information about the Router LED, see LED descriptions on the other side of this quick start guide.

Connect your device to the extended network

If you used WPS to connect your extender to your router, the extender creates two new extender WiFi networks.

The extender's new WiFi network names are based on your existing WiFi network name, with _2GEXT and _5GEXT at the end of the name.

The following table list examples of what your extender's new WiFi network names might look like:

LED descriptions

Log in to the extender

After installation, you can log in to the extender to view or change the extender's settings.

1. Launch a web browser from a computer or mobile device that is connected to your extender network.
   When you are connected to the extender, the Device LED lights.
2. Log in to your extender:
   • If your extender and router use different WiFi network names (SSIDs), visit www.mywifiext.net.
   • If your extender and router use the same WiFi network name (SSID), enter http://<extender's IP address> (for example, http://192.168.1.3).
     To find your extender's IP address, do the following:
     1. Log in to your router.
     2. Find the page in your router web interface that lists the devices connected to your router.
     3. Find your extender in the list and note your extender's IP address.
     4. Enter your extender's IP address in the address field of your web browser.
        A login page displays.
3. Enter your admin email and password and click the LOG IN button.
   The Status page displays.

Support

Thank you for purchasing this NETGEAR product. You can visit www.netgear.com/support to register your product, get help, access the latest downloads and user manuals, and join our community. We recommend that you use only official NETGEAR support resources.

If this product is sold in Canada, you can access this document in Canadian French at https://downloadcenter.netgear.com/other/.

For regulatory compliance information including the EU Declaration of Conformity, visit https://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA

© NETGEAR, Inc., NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non‑NETGEAR trademarks are used for reference purposes only.

NETGEAR INTERNATIONAL LTD
Floor 1, Building 3,
University Technology Centre
Curraheen Road, Cork,
T12EF21, Ireland

August 2019