AirTies Air 4920 Quick Installation Guide

PACKAGE CONTENT

AirTies Air 4920 Expansion Unit

Power Adapter

Ethernet Cable
*Cable colour may vary.

PORTS AND BUTTONS

LED LIGHT BEHAVIOUR

LED Indicators	Conditions	LED Colour	LED Behaviour	Timing
	Power OFF	OFF/Dark
	Power ON	White	Solid (No blinking)
	Device is not ready	White	Blinking
	WLAN is active and the Access Point has an active strong MESH connection on the Access Point	Green	Blinking	50ms OFF 5000ms ON
	WLAN is active and all MESH links on the Access Point are weak	Red	Solid (No blinking)
	Access Point is inactive or searching for radar activity	OFF/Dark
	WPS is in progress	Green	Blinking in sync
	WPS is successful	Green	Solid (No blinking)
	Unconfigured device	Green	Blinking in sync	4000ms OFF 4000ms ON
	WLAN active, device configured, no MESH link on the Access Point	Green	Solid (No blinking)
	There is a configured MESH connection on the Access Point, however connection is inactive (Can't connect)	Red	Blinking	1000ms OFF 1000ms ON
	WPS is not successful	Red

ADDING THE EXPANSION UNIT TO AN EXISTING MESH

Please remove protective plastic cover from the product before installation.

1. Open the AirTies Wi-Fi application on your mobile device.
   

2. Select My Network from the menu.
   

3. Click on + AirTies Unit.
   

4. Follow the instructions on your mobile application to complete your setup. This process should only take a couple of minutes.

ALTERNATIVE: USING THE EXPANSION UNIT AS A STAND-ALONE ACCESS POINT

1. Connect the AirTies Expansion Unit to your existing network using an Ethernet cable.
   
2. Connect the supplied Power Adapter to the AirTies Expansion Unit and then into a power socket. Turn the unit on.
   

• To configure your AirTies Expansion Unit, open an Internet browser (Safari, Chrome, Firefox, Internet Explorer, etc.) on your device (PC, Laptop, Smartphone, Tablet, etc.). Enter "http://air4920.local" in the address bar. The device (PC, Laptop, Smartphone, Tablet, etc.) will present the AirTies Expansion Unit setup page.
• On the AirTies Expansion Unit's setup page, insert the Wi-Fi Name (SSID) and Password, of your choice, and click "Save". The pre-configured (factory) Wi-Fi Name (SSID) and Password can be found on the bottom of the unit.
• You can now connect to the Wi-Fi using the Wi-Fi Name (SSID) and Password configured.

RETURNING UNITS TO FACTORY SETTINGS

To return the unit to factory settings, power on the unit, wait for the Power LED to be lit solid white and press down on the reset button (in a small opening on the back) for 10 – 12 seconds. A metal paperclip is a good choice to do this. When the reset process is successfully triggered, the LEDs in the front will temporarily "blink" and the unit will reboot (in about 2 minutes) to factory settings.

Note: When returning meshed units to Factory Default state, all Access Points need to be reset within 2 minutes of resetting the first unit. If not, settings from the units that have not yet been factory reset will again overwrite the factory settings of the first unit.

PRODUCT SUPPORT

Website

www.nology.co.za/airties

Troubleshooting and Frequently Asked Questions

www.nology.co.za/airties/troubleshooting

If you need assistance with any part of the setup, please do not hesitate to contact Nology Support on 010 980 0001 or alternatively you can send an email to airties.support@nology.co.za. Our Office Hours are from 08:00 to 17:00 Monday to Thursday and from 08:00 to 16:00 on Fridays.

This product makes use of software developed by the open source community. Any such software is licensed under the specific license terms applicable to that particular software (like GPL, LGPL, etc.). Detailed information on the applicable licenses and license terms can be found on the device's user interface.

By using this product, you acknowledge that you have reviewed such license terms and that you agree to be bound by them. Where such terms entitle you to the source code of said software, that source code will be made available at cost upon request from AirTies.

To obtain a copy of said source code, please send your request in writing via email to osrb@airties.com or via snail mail to:

AirTies Wireless Communications
Mithat Uluünlü Sokak No.23 Esentepe,
P.K. 34394 Şişli / Istanbul-Turkey

AirTies will mail you a CD with the requested source code at the cost of CD preparation, shipping and handling. For details please contact osrb@airties.com.

EU Declaration of Conformity

Product: 1600 Mbps Video Grade Wireless Booster; 1600 Mbps Smart Mesh Access Point
Model: Air 4920
Manufacturer: AirTies Wireless Networks
Address: Mithat Uluünlü Sok. No: 23 Esentepe Şişli, İstanbul/Turkey

We declare under our sole responsibility that this product complies with the relevant requirements of the following European Directives:

Signed for and on behalf of: AirTies Wireless Networks

8^th of February 2017, Istanbul (Head Off ice)
(Date and Place Of issue)

Metin İsmail Taşkın
CTO (Chief Technology Officer)
(Name, Job, Function&Signature)

The full text of the EU declaration of conformity is available at the following internet address:
http://www.airties.com/declarations-of-conformity.html