Colour Television 21P2 Service Manual Model CE21P2-C (W.Europe) Service Ref. No. CE21P2-C-02 PRODUCT CODE: 111336306 ORIGINAL VERSION: Chassis No. EB4-A Give complete "SERVICE REF. NO." for parts order or servicing, it is shown on the rating sheet on the cabinet back of the TV set.
SAFETY PRECAUTION 1: An isolation transformer should be connected in the 3: When replacing a chassis in the cabinet, always be power line between the receiver and the AC line certain that all the protective devices are installed when a service is performed on the primary of the properly, such as, control knobs, adjustment covers converter transformer of the set.
CIRCUIT DESCRIPTION 1. POWER SUPPLY control) The chroma signal is divided into R-Y and B-Y The power supply circuit of the EB4-A chassis is chroma signals, demodulated in IC201, and output from composed of a rectifier smoothing circuit, an oscillation pin30 (R-Y) and pin31 (B-Y).
Page 5
6. HORIZONTAL OUTPUT Pin33: Green output for OSD A horizontal oscillation signal is output from pin37 of Pin34: Red output for OSD IC201 and switches the drive transistor Q431. This Pin35: Blanking output for OSD switching signal is current amplified by the drive Pin36: H-sync.
SERVICE CONTROL ADJUSTMENT B1 POWER SUPPLY ADJ. AFT ADJ. TU-AGC ADJ. MAIN BOARD SW1901 SW1902 SW1904 SW1903 Prog.+ Prog.- Vol.- Vol.+ IC801 IC201 IF/Video/Croma/Def. Scart 2 Scart 1 R224 H-WIDTH ADJ. HIGH VOLTAGE ADJ. FOCUS ADJ. V-CENTRE ADJ. V-SIZE ADJ. H-CENTRE ADJ.
Page 7
B1 POWER SUPPLY ADJUSTMENT HIGH VOLTAGE & WIDTH ADJUSTMENT 1. Set VR641 to be mechanically centre before [HIGH VOLTAGE ADJUSTMENT] pressing the mains ON/OFF switch. 1. Tune the receiver to the circular pattern. 2. Tune the receiver to a PAL circular pattern. 2.
CIRCUIT ALIGNMENT 10kΩ 0.002µF 75Ω 1kΩ VIF alignment Output probe Input probe SETTING Adjustment Waveform DC 15.5V C644 + By using T141, adjust "P" to AGC voltage (4.3-4.5V) IC201-pin48 be maximum amplitude. Output probe IC201-pin45 (Side b) Input probe IC201-pin7 Marker frequency 38.9MHz Sweep ATT...
INITIALISATION (Important Notice) When you replace a memory IC (IC802), it is 2. Select the desired service item by using the Function necessary to initialise the IC as following step. button on the remote control handset. 3. Change the data by using the Level + or - button A.
CHASSIS ELECTRICAL PARTS LIST Product safety should be considered when a component replacement is made in any area of a receiver. Components indicated by a mark in this parts list and the circuit diagram show components whose value have special significance to product safety. It is particularly recommended that only parts specified on the following parts list be used for components replacement pointed out by the mark.
Page 18
Part No. Description Description Ref. No. Ref. No. Part No. 421 003 3902 SAW F TSF5315U 409 120 7607 IC MN4052B X151 610 015 2854 TRAP,CERAMIC 5.5MHZ 409 051 2801 IC TC4052BP X152 610 015 3011 TRAP,CERAMIC 6.5MHZ 409 059 2209 IC UPD4052BC X201 645 025 2631...
Page 19
All information in this manual is correct at the start of C701 403 073 2910 CERAMIC 390P K production. Sanyo reserves the right to modify C711 403 073 2910 CERAMIC 390P K components and procedures in order to comply with...
Page 20
Sanyo Industries (UK) Ltd Printed in UK...
Page 21
Some voltages may vary with sulla massa del chassis, i valori di voltag- ficato altrimenti. lare importanza per il sicuro funziona- 21P2/CE21P2-C cance to product safety. It is particu- signal strength. Number: gio presi usando un segnale di barre col- mento del TV.